Nilfisk-ALTO 3.4 user manual Output EQ, Output Gain, Output Pol

Page 22

5.3.4 Output EQ

Output equalizer with 5 parametric filters.

Also called Channel EQ, allows to alter the tone of each individual output.

The characteristics of quality and programmability are identical to those of the Input Equalizer and enable this unit to be used extremely effectively and flexibly.

O u t p u t

E Q

Each equalizer has 5 pages (one per filter), indicating the name of the output it effects and the number of the filter.



		O	P	1				E	Q	1			P	e	a	k
			2	k	0	0		1	.	0				+	1	.	5

Example: Output 1 - Filter 1

Since technical specifications and editing fields of the Output EQ are identical to those of the Input EQ, please refer to INPUT EQ section for descriptions.

5.3.5 Output Gain

Output level control

Allows to adjust the signal level of each individual output.

O u t p u t

G a

i n

Editing values are between +6dB ~ -30dB, with 0.5dB steps.

O P 1

G A I N

- 6 . 5 d B

Note: The level of each output is shown by the respective OUTPUT LEVEL LED ladder. To avoid distortion, don't let the red CLIP LED light up. As automatic protection, you can also enable the LIMITER (EDIT menu) on the outputs that require it. In this case, remember that enabling the LIMITER changes the display mode on the relative LED ladder: in fact, the level shown is no longer the absolute output level, but the level of the signal In relation to the LIMITER threshold.

5.3.6 Output Pol

Controls the output's polarity.

Allows to invert the phase of the signal of individual outputs.

O u t p u t

P o l

Editing values are:

21

Image 22

Contents MAXIDRIVE3.4 Power Supply Safety Related SymbolsImportant Safety Instructions External ConnectionPreface Table of Contents Introduction Rear Panel Outputs Configuration of the systemGetting Started InputsA d P r e s e t 2 x 3 W 3 5 B 2 4 2 x 3 W Adjusting the input signal3 B 2 4 S 5 2 x 2 W + 2 M a P u t I nA G a I N First SetupSystem configuration 3 B 2 4 S 5 2 x 2 W + 2 M a D B A & B G a I NName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M aType of Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExamplePreset Menu Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M aMenu MAP Configuration Description System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D O r e P r e s e t O p e r a H a l l Store & Naming PresetO r e P r e s e t 2 x 2 W + 2 M a E s e t N a m i n W + 2 M aT P r e s e t 2 W + 2 M a Dump Out PresetIncoming Dump C o m i n g D u m p N o r e C e p t Delay Menu M S P u t D e l a yL a Y T p u tEdit menu 2 u SInput Gain P u t I ND B Input EQBandwidth Centre Frequency / Cutoff FrequencyGain R u V e r0 0 H z 4 6 H z PhaseF B e s 2 Crossover frequencyEditing values are between +6dB ~ -30dB, with 0.5dB steps Output EQOutput Gain Output PolR m a L a R I T YV e r s e Utility Menu Ganging SubmenuP u t G a n g i n g N g i n gInput Ganging M P e r a t u r e U n i t T p u t G a n g i n gM . T h r e s h . U n i t Units SubmenuP u t S e l e c t G i t a l A l o g T u pT p u t M e t e r s E M u t e S t M u t e D C o n t r a s t M p e r a t u r eK e U p R m a l T e Lock Submenu2 2 W + 2 M a 3 B 2 4 S 5 C kTotal Partial S s w o r d A 1 3 B 2 4 S 5 2 2 W + 2 M aL O C K S s w o r d R DR m a t C a r d R m a t t i n g R m a t D o n e COMM. Setup SubmenuR m a t R d M m . S e t u pInputs a & B, Digital IN, RS485 ConnectionsInputs a & B RS232 Factory Preset ConfigurationOutputs 1 ~ 6, RS485 OUT Special attentions for RS232 interfaceSignal Power OrganizationMAXIDRIVE3.4 Audio Mixer Signal PowerA135 B246 3-WAY Stereo 2X2W Signal Power Audio Mixer High Left High RightA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232Technical Specifications Return Notice Warranty Registration CardTerms and Conditions Seikaku Technical Group Limited