Nilfisk-ALTO 3.4 user manual I N, D B, P u t, Input EQ, Type of filter

Page 18

I n p u t

G a i n

Allows to adjust the amplification of the signal fed in through Inputs A and B.

Editing values are in the range +6dB ~ -30dB, with 0.5dB steps.

I N A

G A I N

- 2 . 5 d B

Note: Setting the input signal of a digital unit is particularly important, much more than on an analog unit, as any saturation of the A/D converter due to an excessively high input signal causes a typical particularly distinct noise. To achieve a good signal/noise ratio, i.e. an up-front distortion free signal, feed a signal in on the MAXI- DRIVE3.4's input and watch the INPUT LEVEL A-BLED ladders. Keep the signal quite high, but make certain the red CLIP LED doesn't light on continually.

5.3.2Input EQ

Input equalizer with 5 parametric filters.

Allows to alter the overall tone of the signal connected to the respective input.

Also called Master EQ, the equalization of the input signal effects all the outputs connected to the input and the input SUM.

This component's characteristic quality and programmability (identical to the output Equalizer) enable it to be Used so effectively and flexibly as to make the use of graphic equalizers often unnecessary.

I n p u t

E Q

IN A

ADC

Each equalizer has 5 pages (one for each filter), showing the name of the input it affects and the number of the filter.



		I	N	A				E	Q	1			P	e	a	k
			2	k	0	0		1	.	0				-	5	.	0

The following editable parameters are available for each filter:

a. Type of filter

Allows to choose among Peaking, Low or High Shelving with a slope of 6 or 12 dB per octave and Notch filter.



		I	N	A				E	Q	1			P	e	a	k
			2	k	0	0		1	.	0				-	5	.	0

Peaking

Low Shelving

High Shelving

Notch

17

Image 18

Contents MAXIDRIVE3.4 Power Supply Safety Related SymbolsImportant Safety Instructions External ConnectionPreface Table of Contents Introduction Rear Panel Outputs Configuration of the systemGetting Started InputsA d P r e s e t 2 x 3 W 3 5 B 2 4 2 x 3 W Adjusting the input signal3 B 2 4 S 5 2 x 2 W + 2 M a P u t I nA G a I N First SetupSystem configuration 3 B 2 4 S 5 2 x 2 W + 2 M a D B A & B G a I NName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M aType of Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExamplePreset Menu Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M aMenu MAP Configuration Description System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D O r e P r e s e t O p e r a H a l l Store & Naming PresetO r e P r e s e t 2 x 2 W + 2 M a E s e t N a m i n W + 2 M aDump Out Preset T P r e s e t 2 W + 2 M aIncoming Dump C o m i n g D u m p N o r e C e p t Delay Menu M S P u t D e l a yL a Y T p u t2 u S Edit menuInput Gain P u t I ND B Input EQCentre Frequency / Cutoff Frequency BandwidthGain V e r R u0 0 H z 4 6 H z PhaseF B e s 2 Crossover frequencyEditing values are between +6dB ~ -30dB, with 0.5dB steps Output EQOutput Gain Output PolL a R I T Y R m aV e r s e Utility Menu Ganging SubmenuN g i n g P u t G a n g i n gInput Ganging M P e r a t u r e U n i t T p u t G a n g i n gM . T h r e s h . U n i t Units SubmenuT u p P u t S e l e c t G i t a l A l o gT p u t M e t e r s E M u t e S t M u t e D C o n t r a s t M p e r a t u r eK e U p R m a l T e Lock SubmenuC k 2 2 W + 2 M a 3 B 2 4 S 5Total Partial S s w o r d A 1 3 B 2 4 S 5 2 2 W + 2 M aL O C K S s w o r d R DR m a t C a r d R m a t t i n g R m a t D o n e COMM. Setup SubmenuR m a t R d M m . S e t u pConnections Inputs a & B, Digital IN, RS485Inputs a & B RS232 Factory Preset ConfigurationOutputs 1 ~ 6, RS485 OUT Special attentions for RS232 interfaceSignal Power OrganizationAudio Mixer Signal Power MAXIDRIVE3.4A135 B246 3-WAY Stereo 2X2W Signal Power Audio Mixer High Left High RightA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232Technical Specifications Warranty Registration Card Return NoticeTerms and Conditions Seikaku Technical Group Limited