Nilfisk-ALTO 3.4 user manual Factory Preset Configuration, Outputs 1 ~ 6, RS485 OUT, RS232

Page 33

Outputs 1 ~ 6, RS485 OUT

2	HOT (+)

3

BALANCED XLR-F

	1				GROUND
		COLD (	)

RS232

PIN 5

PIN 3 PIN 2

RS232 (9Pin-F)

(TXD) PIN2 PIN 3(RXD)

(RXD) PIN3 PIN 2(TXD)

(GND) PIN5 PIN 5(GND)

9 PIN

9 PIN

The wire must be changed between 2,3 pin.

Special attentions for RS232 interface:

1.Be careful not to use the pin-to-pin cable in the system, it may damage the communication part of this unit.

2.Be sure to use the female connector on both sides of the cable.

3.The length of this cable must not exceed 30 meters, or there would be some unexpected communication errors.

4.If you want to use a long distance remote control, it would be better to use shielding wire for this cable.

7.APPLICATION

The following diagrams show the MAXIDRIVE3.4's various system configurations, as if to say, the various input and output hardware combinations.

7.1.Factory Preset Configuration

#	Name	Configuration	Configuration
01	DEFAULT	A135 B246	Default preset - routing = 3-WAY STEREO
02	2X2W+MAX	A13 B24 S56	2-WAY STEREO + 2 MONO FULL-RANGE OUT
03	2X3W	A135 B246	3-WAY STEREO
04	2X3W+MSB+MAX	A13 B24 S56	3-WAY STEREO with MONO SUB + 1 MONO FULL-RANGE OUT
05	4W+2MAX	A1324 S56	4-WAY MONO + 2 MONO FULL-RANGE OUT
06	4W+BSB+2MAX	A123 B4 S56	4-WAY MONO with B-SUB + 2 MONO FULL-RANGE OUT
07	5W+MAX	A12345 S6	5-WAY MONO + 1 MONO FULL-RANGE OUT
08	5W+BSB+MAX	A1234 B5 S6	5-WAY MONO with B-SUB + 1 MONO FULL-RANGE OUT
09	6W	A123456	6-WAY MONO
10	6W+BSB	A12345 B6	6-WAY MONO with B-SUB

32

Image 33

Contents MAXIDRIVE3.4 Important Safety Instructions Safety Related SymbolsPower Supply External ConnectionPreface Table of Contents Introduction Rear Panel Getting Started Configuration of the systemOutputs Inputs3 B 2 4 S 5 2 x 2 W + 2 M a 3 5 B 2 4 2 x 3 W Adjusting the input signalA d P r e s e t 2 x 3 W P u t I nSystem configuration 3 B 2 4 S 5 2 x 2 W + 2 M a First SetupA G a I N D B A & B G a I NType of Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M aName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExampleMenu MAP Configuration Description Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M aPreset Menu System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D O r e P r e s e t 2 x 2 W + 2 M a Store & Naming PresetO r e P r e s e t O p e r a H a l l E s e t N a m i n W + 2 M aDump Out Preset T P r e s e t 2 W + 2 M aIncoming Dump C o m i n g D u m p N o r e C e p t Delay Menu L a Y P u t D e l a yM S T p u t2 u S Edit menuInput Gain D B I NP u t Input EQCentre Frequency / Cutoff Frequency BandwidthGain V e r R u0 0 H z F B e s 2 Phase4 6 H z Crossover frequencyOutput Gain Output EQEditing values are between +6dB ~ -30dB, with 0.5dB steps Output PolL a R I T Y R m aV e r s e Ganging Submenu Utility MenuN g i n g P u t G a n g i n gInput Ganging M . T h r e s h . U n i t T p u t G a n g i n gM P e r a t u r e U n i t Units SubmenuT u p P u t S e l e c t G i t a l A l o gT p u t M e t e r s E M u t e S t M u t e K e U p R m a l T e M p e r a t u r eD C o n t r a s t Lock SubmenuC k 2 2 W + 2 M a 3 B 2 4 S 5Total Partial L O C K A 1 3 B 2 4 S 5 2 2 W + 2 M aS s w o r d S s w o r d R DR m a t R d COMM. Setup SubmenuR m a t C a r d R m a t t i n g R m a t D o n e M m . S e t u pConnections Inputs a & B, Digital IN, RS485Inputs a & B Outputs 1 ~ 6, RS485 OUT Factory Preset ConfigurationRS232 Special attentions for RS232 interfaceOrganization Signal PowerAudio Mixer Signal Power MAXIDRIVE3.4A135 B246 3-WAY Stereo 2X2W High Left High Right Signal Power Audio MixerA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX To / from RS232 Communications PC & one or more MAXIDRIVE3.4 connectionTechnical Specifications Warranty Registration Card Return NoticeTerms and Conditions Seikaku Technical Group Limited