Nilfisk-ALTO 3.4 M p e r a t u r e, K e U p R m a l T e, D C o n t r a s t, Lock Submenu

Page 28

c.Temperature

Used to key in the value of the environmental temperature of place of installation.

The system uses this value to automatically compensate for the differentials due to the difference speed of sound Transmission according to the air temperature.

This allows to set the delays during the sound-check and only have to reset them automatically when necessary (For example during a concert, in the event of big jumps in temperature, etc.).

The editing values are in the following ranges: +60 C ~ -30 C with 1 C steps

140.0 F ~ -22.0 F with 1.8 F steps

T e m p e r a t u r e

2 0 C

T e m p e r a t u r e

6 8 . 0 F

Note: the measurement units can be chosen between C (degrees Centigrade) and F (degrees Fahrenheit) by means of the Temperature Unit function (UTILITY menu - Units submenu).

d. Wake Up

Allows to choose the mode in which MUTE functions are restored when the MAXIDRIVE3.4 is switched on.

The options include:

Normal

Mute

when switched on, the system restores the last

when switched on, the system automatically

MUTE configuration before switching off

sets all the outputs in MUTE

W a k e U p

N o r m a l

W a k e U p

M u t e

e. LCD Contrast

Allows to adjust the Display contrast.

The values are in the following range: 0 (minimum contrast) ~ 32 (maximum contrast).

L C D C o n t r a s t

2 6

5.4.4LOCK SUBMENU

Used to enable or disable the protection of the system against accidental or unauthorized changes.

Lock

Lock

27

Image 28
Contents MAXIDRIVE3.4 Safety Related Symbols Important Safety InstructionsPower Supply External ConnectionPreface Table of Contents Introduction Rear Panel Configuration of the system Getting StartedOutputs Inputs3 5 B 2 4 2 x 3 W Adjusting the input signal 3 B 2 4 S 5 2 x 2 W + 2 M aA d P r e s e t 2 x 3 W P u t I nFirst Setup System configuration 3 B 2 4 S 5 2 x 2 W + 2 M aA G a I N D B A & B G a I NNumber Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M a Type of Preset 3 B 2 4 S 5 2 x 2 W + 2 M aName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExamplePreset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M a Menu MAP Configuration DescriptionPreset Menu System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D Store & Naming Preset O r e P r e s e t 2 x 2 W + 2 M aO r e P r e s e t O p e r a H a l l E s e t N a m i n W + 2 M aT P r e s e t 2 W + 2 M a Dump Out PresetIncoming Dump C o m i n g D u m p N o r e C e p t Delay Menu P u t D e l a y L a YM S T p u tEdit menu 2 u SInput Gain I N D BP u t Input EQBandwidth Centre Frequency / Cutoff FrequencyGain R u V e r0 0 H z Phase F B e s 24 6 H z Crossover frequencyOutput EQ Output GainEditing values are between +6dB ~ -30dB, with 0.5dB steps Output PolR m a L a R I T YV e r s e Utility Menu Ganging SubmenuP u t G a n g i n g N g i n gInput Ganging T p u t G a n g i n g M . T h r e s h . U n i tM P e r a t u r e U n i t Units SubmenuP u t S e l e c t G i t a l A l o g T u pT p u t M e t e r s E M u t e S t M u t e M p e r a t u r e K e U p R m a l T eD C o n t r a s t Lock Submenu2 2 W + 2 M a 3 B 2 4 S 5 C kTotal Partial A 1 3 B 2 4 S 5 2 2 W + 2 M a L O C KS s w o r d S s w o r d R DCOMM. Setup Submenu R m a t R dR m a t C a r d R m a t t i n g R m a t D o n e M m . S e t u pInputs a & B, Digital IN, RS485 ConnectionsInputs a & B Factory Preset Configuration Outputs 1 ~ 6, RS485 OUTRS232 Special attentions for RS232 interfaceSignal Power OrganizationMAXIDRIVE3.4 Audio Mixer Signal PowerA135 B246 3-WAY Stereo 2X2W Signal Power Audio Mixer High Left High RightA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232Technical Specifications Return Notice Warranty Registration CardTerms and Conditions Seikaku Technical Group Limited