Nilfisk-ALTO 3.4 user manual T P r e s e t 2 W + 2 M a, Dump Out Preset, Incoming Dump

Page 14

P r e s e t N a m i n

M 2 W + 2 M A X

5.1.3Dump Out PRESET

Use this menu page to download a PRESET via the serial ports.

It is also used to immediately "copy" the settings of the various PRESETS of a MAXIDRIVE3.4 to another MAXIDRIVE3.4.

Du m 2

U

O u t P r e s e t

2 x 2 W + 2 M A X

To download a PRESET:

Use DIAL to reach the required PRESET. Press ENTER.

Note: The menu page remains unchanged to allow other PRESETS to be dumped.

All the Preset s data (name, configuration, parameter values, etc.) are immediately transmitted to the units connected to the serial ports (other MAXIDRIVE3.4, computers, etc.).

Note: In order for the transfer to have effect, the receiving units must be able to identify and accept Incoming Dump operations.

When two or more MAXIDRIVE3.4 are connected, the PRESET sent by the transmitting MAXIDRIVE3.4 (TX) overwrites (and therefore cancels) the existing PRESET in the same memory position of the receiving MAXI- DRIVE3.4 (RX).

MAXIDRIVE3.4 #1

Incoming Dump

SEND

..

Preset #2

Preset #3

Preset #4

Preset #5

Preset #6

Preset #7

Preset #8

Preset #9

..

DUMP

PORT

SERIAL

MAXIDRIVE3.4 #2

Incoming Dump

ACCEPT

..

#2 MySetup

#3 MySetup5

#4 LiveSet

Preset #5

#6 Monitor

#7 Monitor2

#8 Monitor3

#9 Side

..

DUMP

PORT

SERIAL

MAXIDRIVE3.4 #3

Incoming Dump

IGNORE

..

#2 SideField

#3 Concert1

#4 Concert2

#5 Concert3

#6 Concert4

#7 Remote1

#8 Remote2

#9 Remote2

..

5.1.4 Incoming Dump

Used to accept or ignore the Dump of a PRESET sent from another MAXIDRIVE3.4 or from a computer via serial.

Ports settings can be:

13

Image 14
Contents MAXIDRIVE3.4 Power Supply Safety Related SymbolsImportant Safety Instructions External ConnectionPreface Table of Contents Introduction Rear Panel Outputs Configuration of the systemGetting Started InputsA d P r e s e t 2 x 3 W 3 5 B 2 4 2 x 3 W Adjusting the input signal3 B 2 4 S 5 2 x 2 W + 2 M a P u t I nA G a I N First SetupSystem configuration 3 B 2 4 S 5 2 x 2 W + 2 M a D B A & B G a I NName of the Preset 3 B 2 4 S 5 2 x 2 W + 2 M a Number Of Presets 3 B 2 4 S 5 2 x 2 W + 2 M aType of Preset 3 B 2 4 S 5 2 x 2 W + 2 M a ExamplePreset Menu Preset Modifications 1 3 B 2 4 S 5 2 x 2 W + 2 M aMenu MAP Configuration Description System Protection 3 B 2 4 S 5 2 x 2 W + 2 M aC a R D O r e P r e s e t O p e r a H a l l Store & Naming PresetO r e P r e s e t 2 x 2 W + 2 M a E s e t N a m i n W + 2 M aIncoming Dump Dump Out PresetT P r e s e t 2 W + 2 M a C o m i n g D u m p N o r e C e p t Delay Menu M S P u t D e l a yL a Y T p u tInput Gain 2 u SEdit menu P u t I ND B Input EQGain Centre Frequency / Cutoff FrequencyBandwidth 0 0 H z V e rR u 4 6 H z PhaseF B e s 2 Crossover frequencyEditing values are between +6dB ~ -30dB, with 0.5dB steps Output EQOutput Gain Output PolV e r s e L a R I T YR m a Utility Menu Ganging SubmenuInput Ganging N g i n gP u t G a n g i n g M P e r a t u r e U n i t T p u t G a n g i n gM . T h r e s h . U n i t Units SubmenuT p u t M e t e r s E M u t e S t M u t e T u pP u t S e l e c t G i t a l A l o g D C o n t r a s t M p e r a t u r eK e U p R m a l T e Lock SubmenuTotal Partial C k2 2 W + 2 M a 3 B 2 4 S 5 S s w o r d A 1 3 B 2 4 S 5 2 2 W + 2 M aL O C K S s w o r d R DR m a t C a r d R m a t t i n g R m a t D o n e COMM. Setup SubmenuR m a t R d M m . S e t u pInputs a & B ConnectionsInputs a & B, Digital IN, RS485 RS232 Factory Preset ConfigurationOutputs 1 ~ 6, RS485 OUT Special attentions for RS232 interfaceSignal Power OrganizationA135 B246 3-WAY Stereo 2X2W Audio Mixer Signal PowerMAXIDRIVE3.4 Signal Power Audio Mixer High Left High RightA1324 S56 4-WAY4 Mono + 2 Mono AUX 4W+2MAX Communications PC & one or more MAXIDRIVE3.4 connection To / from RS232Technical Specifications Terms and Conditions Warranty Registration CardReturn Notice Seikaku Technical Group Limited