Assembly Instructions | McCulloch 6096201212 instruction

3 - ASSEMBLY INSTRUCTIONS

3-1. INTRODUCTION

This unit is designed for occasional homeowner use and should not be used for commercial purposes or subjected to heavy continuous use.

Your new chain saw can be used for a variety of projects such as cutting firewood, making fence posts, felling small trees, limbing, pruning at ground level, and light carpentry. Cut only wood or wood products with your saw.

3-2. UNPACKING

1.Remove all items from carton.

2.Check all items for any shipping damage. If you find any damage or if any parts are missing, promptly inform dealer where you bought the pole saw.

3-3. ASSEMBLY REQUIREMENTS

Your new pole saw will require adjustment of chain and fill- ing the oil tank with lubricating oil before the unit is ready for operation. Do not start the saw motor until the unit is properly prepared.

Read all instructions carefully. Do not install any other size bar and chain than what is recommended for your model.

3-4. GUIDE BAR / SAW CHAIN REPLACEMENT INSTALLATION

WARNING

Whenever handling the saw chain, wear work gloves for protection against sharp cutting edges.

1.Remove bar nuts, push bar bolts in and slide sprock- et support down. (See Fig. 3-4A)

2.Remove old guide bar and chain.

3.Using a straight screwdriver, turn the chain adjust- ment screw counterclockwise as far as it will go, or until tang is to the end of its travel.

4.Loop saw chain over drive sprocket with the cutting edges of the chain pointing in the direction of rotation.

5.Place the slotted end of guide bar over the bar bolt so the tang fits into the lower hole in the guide guide bar.

6.Make sure the chain follows the slot in the guide bar. Slide the sprocket support up and push the bar bolts through the sprocket support.

7.Install the bar retaining nuts hand tight, (Proceed to saw chain tension Adjustment).

Guide Bar Bolts

Saw Chain

		Guide Bar
		Adjusting Hole
	Drive Sprocket	Guide Bar Nuts
	Tang	Adjusting Plate
	Tang	Adjusting Screw
		Adjusting Screw

Sprocket Support

3-4A

3-5. SAW CHAIN TENSION ADJUSTMENT

Proper tension of the saw chain is extremely important and must be checked before starting, as well as during, any cut- ting operation. Taking the time to make needed adjust- ments to the saw chain will result in improved cutting per- formance and prolonged chain life.

NOTE: A new chain and bar will need readjustment after as few as 5 cuts. This is normal during the break-in period, and the interval between future adjustments will lengthen quick- ly (Figure 3-5A).

CAUTION

If a chain is TOO LOOSE or TOO TIGHT, the bar chain and saw bearings will wear more rapidly. Study Figure 3-5A for information concerning correct cold tension (A), correct warm tension (B), and as a guide for when saw chain needs adjustment (C).

TO ADJUST SAW CHAIN TENSION:

1.Loosen the bar retaining nuts (D) so they are hand tight. (See Fig. 3-5B)

2.Holding the nose of the bar up, use the screwdriver or scrench if provided in your User’s Kit to turn the guide bar adjustment screw (E) (Fig. 3-5C) clockwise to tighten the chain. Turning the screw COUNTER- CLOCKWISE LOOSENS THE CHAIN on the guide bar.

3.After adjustment and while wearing heavy duty work gloves, move the saw chain back and forth on the guide bar to be sure the chain moves freely and is in proper mesh with sprocket. Do not move chain with bare hands.

NOTE: IF the chain is difficult to rotate or if it binds on the guide bar, too much tension has been applied and must be adjusted. To decrease tension, turn the adjustment screw counterclockwise slowly. Move the chain back and forth until it moves freely.

4.Holding the nose in upper position, securely tighten the bar retaining nuts (70 inch lbs.)

ABC

3-5A

3-5B

3-5C

3-6. ASSEMBLY OF POLE SAW

1.Make sure the unit is unplugged from power source.

2.Slip handle bracket (A) over chain saw handle from the right side (See Fig. 3-6A). NOTE: The trigger must be depressed before the bracket will go onto the han- dle. Push the lock-off button and depress the trigger. While holding the trigger in, place the trigger support portion of the bracket under the trigger and slide the bracket onto the chain saw handle. The bracket will keep the trigger in the “ON” position.

3.Align holes in pole bracket with holes in handle brack- et. Install Phillips head screws with lock washers through pole bracket from left side and thread into the weld nuts on the handle bracket. Tighten screws securely.

4.Plug the saw power cord into receptacle cord at end of inner pole.

B 3-6A

3-7. ADJUSTING POLE LENGTH

The pole saw has a telescoping pole assembly that will extend from 57 inches (fully retracted) to 96 inches (fully extended). A threaded compression coupling is used to hold the pole in position at any extended length.

1.To extend the pole, loosen coupling by turning cou- pling nut counterclockwise as shown in Fig. 3-7A. Pole will slide freely.

2.Pull inner pole section out to desired length of exten- sion. Note: Only extend pole to minimum length required to reach limb that is being cut.

3.To lock pole in position, tighten coupling by turning coupling nut clockwise (See Fig. 3-7A) until firmly hand tight. Make sure saw handle is aligned with pole handle before tightening coupling nut.

IMPORTANT: Do not use wrench or pliers to over- tighten coupling. Damage to coupling or pole may result.

UNLOCKLOCK

3-7A