Troy-Bilt 1925 Operation, Jump Start Procedure, Connecting Electrical Loads, Stopping the Engine

Page 9

Section 4: Operation

Jump Start Procedure

If the generator’s starting battery fails, use the following instructions to jump start your generator.You can jump start the generator using any 12 Volt automotive or utility style storage battery.

1.Unscrew the fuse holder and remove the generator’s 10 Amp in-line fuse (Figure 4).Verify the fuse is good or replace with a known good fuse. Reinstall fuse in the fuse holder.

Figure 4 — In-Line Fuse

2.Slide the red rubber boot off the generator’s battery terminal and push it onto the red wire, thus uncovering the POSITIVE battery terminal.

3.Using standard automotive jumper cables, connect the RED jumper cable clamp to the generator’s POSITIVE battery terminal (Figure 5).

Figure 5 — Jumper Cable Connections

Grounding

Fastener

4.Connect the other RED jumper cable clamp to the starting battery’s POSITIVE battery terminal.

5.Connect the BLACK jumper cable clamp to the starting battery’s NEGATIVE battery terminal.

6.Connect the other BLACK jumper cable clamp to the GROUNDING FASTENER on the generator, as shown in Figure 5.

7.Start the generator as described in “Starting the Engine” and remove jumper cables in reverse order of connections.

8.Slide the red rubber boot back onto the generator’s POSITIVE battery terminal.

If you have any questions, please call the Generator Helpline at 1-888-611-6708,M-F8-5 CT.

IMPORTANT: When jump starting, always wear proper eye protection and never lean over battery. Inspect both batteries before connecting booster cables. DO NOT jump start a damaged battery. Be sure vent caps are tight and level.

Connecting Electrical Loads

•Let engine stabilize and warm up for a few minutes after starting.

•Plug in and turn on the desired 120 and/or 240 Volt AC, single phase, 60 Hz electrical loads.

•DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.

•DO NOT connect 3–phase loads to the generator.

•DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD GENERATOR. See “Don’t Overload Generator” on page 13.

Stopping the Engine

1.Unplug all electrical loads from generator panel receptacles. NEVER start or stop engine with electrical devices plugged in and turned ON.

2.Let engine run at no-load for several minutes to stabilize internal temperatures of engine and generator.

3.Turn start switch to “Stop” position.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Questions? Preguntas? Helpline 1-888-611-6708 M-F8-5 CT Portable Generator / Generador Portátil Model / ModeloTable of Contents Safety RulesEquipment Description Generator produces powerful voltage Unintentional sparking can result in fire or electric shock Know Your Generator Features and Controls SectionAttach Negative Battery Cable AssemblyTo install Remove Generator From CartonBefore Starting the Engine AssemblyAttach Handle Add Engine Oil and FuelUsing the Generator Section OperationOperating Generator Connecting Electrical Loads Jump Start ProcedureOperation Stopping the EngineCharging a Battery How to Use the Battery ChargerTo recharge 12 Volt batteries, proceed as follows Permanent Cold Weather Shelter Cold Weather Generator Adapter Operation Cord SETVolt DC, 10 Amp Receptacle ReceptaclesVolt AC, 20 Amp, Duplex Receptacles 120/240 Volt AC, 30 Amp, Locking ReceptacleDont Overload Generator Power ManagementCapacity ExampleSection Maintenance General Maintenance RecommendationsEngine Maintenance Generator Maintenance MaintenanceBattery Maintenance Generator CleaningStorage StorageGenerator Storage Engine Storage Other Storage TipsTroubleshooting TroubleshootingProblem Cause Correction Schematic Section Wiring Diagram and SchematicWiring Diagram Wiring Diagram and SchematicExploded View Main Unit Section Exploded Views and Parts ListsParts List Main Unit Exploded Views and Parts ListsDescription Parts Not IllustratedAC Control Panel Exploded View & Parts List DC Control Panel Exploded View & Parts List Alternator Exploded View & Parts List Page Tabla DE Contenidos Reglas de SeguridadDescripción DEL Equipo Reglas DE SeguridadPeligro Sección 1 Reglas de SeguridadPrecaución Sección 1 Instrucciones de SeguridadCaracterísticas y Mandos Conozca SU GeneradorCulatazo el Principio Usó para comenzar motor Montaje MontajePara Retirar El Generador De La Caja Conecte el Cable Negativo de la BateríaAntes DE Darle Arranque AL Motor Sección 3 MontajeFije el Asa Agregar Aceite al Motor y CombustibleOperación USO DEL GeneradorOperando EL Generador Precaución Procedimiento de Arranque en Puente Sección 4 OperaciónConexion De Cargas Electricas Parado Del MotorCargador de Batería Carga de la BateriaFigura 24 Refugio Frío Permanente del Tiempo Operación Durante UN Clima FríoJuego DE Cables DEL Adaptador DEL Generador ReceptáculosTomacorrientes de 12 Voltios DC 120/240 Voltios AC, 30 Amp, Receptáculo de Seguridad Volt AC, 20 Amp, Receptáculos DoblesCapacidad No Sobrecargue EL GeneradorControl de la Energía EjemploRecomendaciones Generales DE Mantenimiento MantenimientoMantenimiento del Motor Cambio del AceiteMantenimiento del Generador Sección 5 MantenimientoMantenimiento de la Batería Para Limpiar el GeneradorAlmacenamiento AlmacenamientoAlmacenando el Generador Almacenando el MotorDiagnosticos de Averías Problemo Causa AccionDiagnositicos DE Averías Efectiva desde el 12 ro de Noviembre Equipo Para Uso Del Consumidor Para Uso ComercialAcerca de la seguridad de su equipo TROY-BILT Owner Warranty Policy Effective November 12 About your equipment warrantyEquipment Consumer Use Commercial Use

1925 specifications

The Troy-Bilt 1925 is a versatile and powerful lawn care machine, designed to handle a myriad of landscaping tasks with ease and efficiency. Renowned for its robust construction and user-friendly features, the Troy-Bilt 1925 is an ideal choice for both residential homeowners and professional landscapers alike.

One of its standout features is the powerful engine. The Troy-Bilt 1925 is equipped with a reliable 25 HP engine that delivers plenty of power to tackle even the toughest mowing conditions. Whether you're mowing dense grass, tackling overgrown weeds, or navigating steep terrain, this engine offers the necessary torque and performance to get the job done without stalling or straining.

The cutting deck is another impressive aspect of the Troy-Bilt 1925. With a generous cutting width of 54 inches, users can cover large areas efficiently, reducing the time spent mowing. The deck height is easily adjustable, allowing for customized cutting heights to suit different grass types and lengths. Users can achieve a perfectly manicured lawn with minimal effort.

In terms of technology, the Troy-Bilt 1925 features advanced cutting system technology that enhances the quality of cut and offers superior grass discharge. The integrated side discharge and mulch capabilities provide options for grass management, catering to different user preferences. Additionally, the large-capacity fuel tank ensures extended mowing sessions without frequent refueling interruptions.

Comfort and ease of use are paramount in the design of the Troy-Bilt 1925. The ergonomic seating and dashboard controls ensure that operators remain comfortable during longer mowing sessions. The intuitive control layout allows for easy maneuverability, while the responsive steering system enhances navigation around obstacles such as trees and flower beds.

Moreover, the Troy-Bilt 1925 is built to last, featuring a durable frame and high-quality components that withstand the rigors of consistent use. The stability and traction provided by its heavy-duty tires ensure safe operation on various terrains.

In conclusion, the Troy-Bilt 1925 is an excellent choice for anyone seeking a reliable, efficient, and powerful lawn care machine. With its combination of a strong engine, wide cutting deck, advanced technology, and user-centric design, it stands out as a leader in outdoor power equipment, capable of maintaining impressive lawns and landscapes with ease and precision.
Top Page Image Contents