Troy-Bilt 20240 manual Nozzle Maintenance, Ring Maintenance

Page 16

Section 5: Maintenance

1.Detach spray gun and nozzle extension from high pressure hose. Detach nozzle extension from spray gun and remove o-ring and screen from nozzle extension. Flush screen, spray gun, and nozzle extension with clean water to clear debris.

2.Place in-line filter screen into threaded end of nozzle extension. Direction does not matter. Push screen in with eraser end of pencil until it rests flat at bottom of opening.Take care not to bend the screen.

3.Place o-ring into recess. Push o-ring snugly against in-line filter screen.

4.Assemble nozzle extension to spray gun, as described earlier in manual.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure.The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc.To correct the problem, immediately clean the nozzle following these instructions:

1.Shut off engine and turn off water supply.

2.Remove nozzle from end of nozzle extension.

3.Remove in-line filter from other end of nozzle extension.

4.Use a small paper clip to free any foreign material clogging or restricting nozzle (Figure 22).

Figure 22 — Nozzle Maintenance

Use wire here

to remove

debris.

5.Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 23). Back flush between 30 to 60 seconds.

Figure 23 — Backflushing the Nozzle Extension

6.Reinstall nozzle and in-line filter into nozzle extension.

7.Reconnect nozzle extension to spray gun.

8.Reconnect water supply, turn on water, and start engine.

9.Test pressure washer by operating with each quick connect nozzles.

O–Ring Maintenance

Purchase an O–Ring/Maintenance Kit, part number 191922GS by contacting the nearest authorized service center. It is not included with the pressure washer.This kit includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service your unit’s o-rings.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

•NEVER repair leaking connections with sealant of any kind. Replace o-ring or seal.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Advertencia Manual No GS Revision 5 11/09/2005Safety Rules Table of ContentsEquipment Description When Adding Fuel Operate pressure washer only outdoorsUnintentional sparking can result in fire or electric shock High pressure spray may damage fragile items including glass Section Features and Controls Know Your Pressure WasherChoke Lever Prepares a cold engine for starting Oil Fill/Dipstick Check and fill with oil hereAssembly Assembly SectionPreparing Pressure Washer for USE Assembly Add Engine Oil and FuelSpray Gun Hook Place pressure washer on a level surfaceConnect Hose and Water Supply to Pump Checklist Before Starting EngineConnect high pressure Hose here HOW to USE Your Pressure Washer How to Start Your Pressure WasherSection Operation Pressure Washer LocationEngage trigger lock on spray gun when not in use How to Stop Your Pressure WasherOperation How to Use ProjectPro Nozzle System How to Use Accessory TrayFollow these instructions to change ProjectPro nozzles How to Use the Rotating and Utility Brushes How to Use the Turbo NozzleTo attach a brush to the gun Cleaning and Applying Detergent Cleaning Detergent Siphoning TubePressure Washer Rinsing Automatic Cool Down SystemMaintenance Section SpecificationsGeneral Maintenance Recommendations Pressure Washer MaintenanceNozzle Maintenance MaintenanceRing Maintenance Engine Maintenance Pump MaintenanceData Tag Changing Pump OilStorage Preparing the Unit for StorageStoring the Engine Protecting the PumpTroubleshooting TroubleshootingProblem Cause Correction Page TROY-BILT Owner Warranty Policy Effective November 1 About your equipment warrantyEquipment Consumer Use Commercial Use Portable Generator Years 2nd year parts onlyReglas de Seguridad Conserve Estas InstruccionesTabla DE Contenidos Descripción DEL EquipoSección 1 Reglas de Seguridad Cuando Añada CombustibleCuando Pruebe LA Bujía DEL Motor Precaución Características y Controles Conozca SU Maquina Lavadora DE PresionMontaje MontajePreparando EL Lavadora Alta Presión Para SU USO Agregar Aceite al Motor y Gasolina Sección 3 MontajeColoque la lavadora a presión sobre una superficie nivelada Conecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorDeposite la gasolina adecuada en el tanque del combustible Proporcione el suministro de agua adecuadoOperación Cómo Usar SU Máquina Lavadora a PresiónUbicación del Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónSección 4 Operación Cómo Detener su Máquina Lavadora a PresiónUtilización de la Bandeja de Accesorios Cómo Usar el Sistema de Boquillas ProjectProLa Presión Baja La Presión AltaCómo usar los Cepillos Giratorios y de Utilidad Cómo Usar la Boquilla a ChorroPara montar un cepillo en la pistola Limpieza y Aplicación del Detergente Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Sistema de Enfriamiento Automático Alivio TérmicoMantenimiento EspecificacionesRecomendaciones Generales Mantenimiento DE LA Maquina Lavadora a PresionSección 5 Mantenimiento Revise el Filtro en LíneaMantenimiento de la Boquilla Mantenimiento de los Anillos OMantenimiento DEL Motor Mantenimiento de la BombaEtiqueta de Datos Cambio del aceite de la bombaSección 6 Almacenamiento Preparando LA Unidad Para SU AlmacenamientoAlmacenando EL Motor Proteger la BombaDiagnosticos de Averías Reparacion DE AveriasEfectiva desde el 1 ro de Noviembre Equipo Para Uso Del Consumidor Para Uso ComercialGenerador Portátil Año

20240 specifications

The Troy-Bilt 20240 is a popular model among homeowners looking for a reliable and efficient snow thrower. Designed to tackle moderate to heavy snowfall, this snowblower boasts a range of features that enhance its performance and ease of use.

One of the standout characteristics of the Troy-Bilt 20240 is its 24-inch clearing width and 21-inch intake height, allowing it to effectively handle large amounts of snow. The powerful 243cc engine provides the necessary strength to clear driveways, sidewalks, and patios with minimal effort.

The snow thrower is equipped with a self-propelled system, enabling users to navigate through deep snow with ease. With six forward and two reverse speeds, operators can select the right speed for their working conditions, ensuring maximum efficiency and control. This versatility makes it suitable for various snow depths and terrains.

The 20240 features an adjustable chute that can rotate a full 180 degrees, allowing users to direct the snow where it is needed. This is particularly advantageous for clearing snow away from pathways or driveways without creating additional obstacles. The chute can be easily adjusted using a remote, adding to the user-friendly design of the machine.

Durability is a key aspect of the Troy-Bilt 20240. It incorporates a heavy-duty steel frame and reinforced poly skid shoes that resist wear and tear from rugged winter conditions. This robust construction ensures that the snow thrower can withstand the challenges posed by harsh weather and heavy snowfall.

Additionally, the snow blower's touch control system offers enhanced maneuverability, enabling operators to make quick adjustments on the fly. The ergonomic hand grips provide comfort during extended use, reducing fatigue and improving handling.

Another notable technology feature is the electric start, which simplifies the starting process, particularly in cold weather. This convenient option eliminates the hassle of pulling cords, making it accessible for users of all experience levels.

In summary, the Troy-Bilt 20240 combines power, durability, and advanced features, making it an excellent choice for homeowners who need an effective snow removal solution. Its impressive capabilities and user-friendly design ensure that it stands out in the competitive market of snow throwers, providing reliability and performance season after season.
Top Page Image Contents