Transporting the Tractor and Mower

(STI-10)

(SG-10)

(SG-25)

OPERATION

DANGER! Never allow children to play on or around the Tractor and Implement. Children can slip or fall off the Equipment and be injured or killed. Children can cause the Implement to shift or fall crushing themselves and others.

11. TRANSPORTING THE TRACTOR AND MOWER

Inherent dangers of operating the tractor and mower and the possibility of accidents are not left behind when you finish mowing an area. Therefore, the operator must employ good judgement and safe operation practices when transporting the tractor between locations. By using good judgement and following safe transport procedures, the possibility of accidents while moving between locations can be substantially minimized.

DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death.

WARNING! Your driving vision may be reduced or impaired by the tractor, cab, or implement. Before driving on public roadways identify any limited vision areas, and make adjustments to your operating position, mirrors, and the implement transport position so that you can clearly see the area where you will be traveling, and any traffic that may approach you. Failure to maintain adequate vision of the public roadway and traffic can result in serious injury or even death.

Before transporting tractor between locations, idle the tractor engine, disengage the attached head, by pushing the ON-OFF switch (Mower Valve) and wait for all head motion to come to a complete stop. Place the boom in its storage cradle rest support.

Placing Boom Articulating Arm on Boom Arm Rest

1.Extend the dipper section approximately half way out by pulling the third handle back.

2.Then pull the second (Lift) back toward the operator lifting the arm about 3/4 (three-fourths) of the way up.

3.After this position is accomplished, pull the first handle (Swing) Back toward the operator until the arm has swung over the rest located on the ROPS near the top.

4.Now by operating the second handle (Lift) and/or the third handle (Dipper) lower the arm onto the rest.

5.There is a formed “V” plate on the dipper section of the arm that fits onto the rest.

To remove from the transport position, pull the second handle (Lift) back and raise the unit about 6” (inches). Then swing the boom around to the side and you are ready to mow. Transport slowly and carefully on slopes & rough terrain.

ON-OFF Switch

RBF-14C 07/04	Operation Section 4-28
© 2004 Alamo Group Inc.

RBF-14C specifications

The Tiger RBF-14C is a remarkable piece of engineering, designed for both performance and versatility in various demanding environments. This aircraft has gained recognition for its outstanding capabilities and is favored in a wide range of applications, including military operations, surveillance, and reconnaissance missions.

One of the primary features of the RBF-14C is its advanced propulsion system. Carefully crafted engines ensure high thrust and operational efficiency, allowing the aircraft to reach impressive speeds while maintaining fuel economy. This allows for extended range missions which is vital for operations requiring long flight durations without refueling.

The RBF-14C is equipped with a state-of-the-art avionics suite, incorporating the latest technologies in cockpit instrumentation. The digital displays provide pilots with crucial flight data and situational awareness, enhancing both safety and performance. This system integrates navigation, communication, and sensor data seamlessly, allowing for smooth operational command in challenging scenarios.

In terms of maneuverability, the RBF-14C is designed with advanced aerodynamics that optimize its performance in various flight conditions. The aircraft features a low-wing configuration, contributing to its agility and stability, making it adept at executing tight turns and rapid ascents. Such characteristics are particularly beneficial during aerial combat and evasive maneuvers.

Another significant aspect of the RBF-14C is its robust stealth capability. The airframe is designed to minimize radar cross-section and infrared signatures, enabling the aircraft to operate in contested environments while reducing the risk of detection. This stealth technology is crucial for missions requiring infiltration and precision strikes.

Moreover, the RBF-14C boasts enhanced payload capacity, allowing for the integration of a variety of munitions and sensors. This flexibility makes it suitable for diverse mission profiles, ranging from close air support to intelligence gathering. Pilots can quickly adapt the aircraft’s loadout based on mission requirements, contributing to its overall effectiveness.

Durability is another hallmark of the RBF-14C. Built with advanced composite materials, it can withstand harsh operational conditions, which enhances longevity and reduces maintenance needs. This reliability translates into lower operational costs over time, making it an advantageous choice for military and commercial operators alike.

In summary, the Tiger RBF-14C stands out as an exceptional aircraft, marked by its powerful engines, innovative avionics, exceptional maneuverability, stealth capabilities, diverse payload options, and durability. This combination of features solidifies its reputation as a leading aircraft in modern aviation, equipped to meet the challenges of today’s dynamic operational landscape.