Walker MT owner manual Non-Tilting Decks, Deck Secured in UP Position, Tilt-Up Decks

Page 62

Maintenance Instructions

CLEANING

Grass Buildup in Mower Housing

Non-Tilting Decks

DANGER

Before raising or removing the mower deck for cleaning, stop the engine, re- move the ignition key, and disconnect the spark plug wires.

1.Raise the deck and secure it in the UP position by hooking the deck lift rod into the body bracket below the counterweight spring clip. The rod is hinged and is stowed along the footrest of the deck carrier frame. A hitch pin on the end of the rod is used to secure it in place with the deck raised.

DANGER

NEVER operate cutter blades with the deck in the raised position.

Counterweight

Spring Clip

Deck Lift

Rod

Body

Bracket

Deck Secured in UP Position

-2. Clean grass buildup underneath the deck using a pressure washer (and scraper if required).

NOTE: If the buildup is severe, it may be easier to clean the deck by removing the deck assem- bly from the tractor and standing the deck as- sembly on its “nose”.

NOTE: While some degree of material buildup in the mower deck housing can be tolerated, a point is finally reached where cutting quality deteriorates and clogging begins to occur because of too much buildup on the baffling and housing.

Tilt-Up Decks

DANGER

Before raising or removing the mower deck for cleaning, stop the engine, re- move the ignition key, and disconnect the spark plug wires.

1.Raise the deck lock lever handle on each side of the carrier frame and pull out to release car- rier frame for tilting action.

2.Using the carrier frame lift handle, raise deck to the TILT-UPposition and insert the deck hook into the tilt-up latch on the tractor body.

Tilt-Up Latch

Tilt-Up Latch

Tilt-Up Hook

on Deck

Deck Lock Lever

Deck Secured in TILT-UP Position

DANGER

Do not operate the mower with deck in tilt- up position. Do not move the tractor with the deck in the tilt-up position.

3.Clean grass buildup underneath the deck using a pressure washer (and scraper if required).

58

Page 61 Page 63
Image 62
Page 61 Page 63
Contents Please Read and Save These Instructions Foreword Table of Contents REPLACING/REPAIRING Engine Air Cleaner SystemGrass Buildup in Mower Housing Mower Deck Gearbox Replacement GHS Blower AssemblyIdentifying Number Locations General InformationGlossary Fill In By PurchaserServicing of Engine and Drivetrain Components Electrical System SpecificationsEngine TransmissionGround Travel Speed TransmissionTransmission Fluid Blade DriveMower Deck Curb Weight ApproximateTire Pressure Blade Size TypicalDrive Belts SeatComponent Identification Front View and Right Side ViewRear View and Left Side View PTO Top View Engine CompartmentDo not mow with bystanders in the area Safety InstructionsBefore Operating Operating Maintenance Safety Instructions SAFETY, CONTROL, and Instruction Decals SAFETY, CONTROL, and Instruction Decals Battery Service Assembly InstructionsSetup Instructions Wet Battery ServiceBattery Installation Mower Deck Assembly Battery ChargingBattery Installation Deck Caster Wheels InstallationDeck Installation Deck Caster Wheel InstallationDischarge Shield Installation On Side Discharge Deck Mower Deck lnstallation on TractorCoupler Ring Locked Position Installing PTO Quick CouplerMower Deck Installation PTO Shaft Connection Deck Leveling Deck Counterweight Spring InstallationMachine must be shut off during this procedure Deck LevelingRefer to Adjustments of Carburetor in Mainte TionsDeck Secured in TILT-UP Position Refer to Gear Axle Lubrication in MaintenanceRefer to CHECKING/SERVICING the Battery Adjust Mower Cutting HEIGHT, if RE- Quired Engine Choke Operating InstructionsControl IDENTIFICATION, LOCATION, and Function Operating ControlsSteering Levers Choke and Throttle LocationEngine Throttle Blade Clutch PTOOptional Cold Start Lever Jackshaft Drive Belt Release Front Body Latch ReleaseLockout Lever Location Optional Cold Start Lever Normal Operating PositionOperating Controls Top View from Drivers Point of View Instrument Panel Hourmeter Ignition SwitchIgnition Switch VoltmeterOptional Cold Start Lever Starting the EngineDisengaged Adjusting Ground Speed and Steering Keep feet on footrests all times when the machine is movingCorrect Operator Hand Position On the Controls Engaging the MowerStopping the Machine Blade Clutch EngagedBlade Clutch Disengaged Lockout Lever Freewheel Position Cutting Height AdjustmentTransmission Lockout Lockout Lever Normal Operating PositionMaximum Recommended Side Slope Recommendations for MowingSide Discharge Shield in Lowest Position Recommendations for TILT-UP Deck OPERATION/TRANSPORT GHS Model Only GHS Flow and ComponentsRotating Blower Blades General InformationBlower Intake Cover Blade Rotation for GHS Mower Deck View from underneath Clogging ChecklistForward Cleaning the GHS Exhaust Screen PowerfilFull Signal Horn Grass Catcher Screen Removal for CleaningTailgate Dumping Catcher Door Safety LatchUsing the Dump Bag 7.0 Bushel Catcher Pinch Point Spring Loaded DoorPower Dump Option Dumping Catcher into Dump BagPower Dump Components Service Item 100 200 Every Daily Hours Yearly 2Years Maintenance InstructionsMaintenance procedures requiring special training or Tools should be performed by a trained technicianImportant Tips for Care of the Kohler Engine Dipstick Operating Range LubricationEngine Oil Oil Drain/Oil Filter Location Grease Fitting and Oil Point LubricationIdent Lubrication Location Type Chassis and Deck Lubrication Points DSD52 or DSD62 Mower Deck Lubrication Mower Deck Gearbox LubricationMower Deck Gearboxes Blade Spindle LubricationGear Axle Lubrication Checking Gearbox Oil LevelDipstick Location, Tractor PTO Gearbox ∙ Change axle oil every 1000 hours or two 2 yearsChanging Hydrostatic Transmission Fluid Checking Hydrostatic Transmission Fluid LevelTransmission Reservoir Air Bleed Plug Location Cleaning Engine Air Cleaner System ComponentsAir Cleaner Components Shown with cover being removed Turbine PrecleanerDonaldson Radialseal Air Cleaner Primary Air Restriction Gauge LocationAir Filter Element Replacement Kohler Air Cleaner Secondary Foam Precleaner Paper ElementAir Intake System Air Filter Reinstallation Engine Cooling SystemEngine Air Intake Screen Cooling Fin Access Panels Cooling System AirflowTilt-Up Decks Non-Tilting DecksDeck Secured in UP Position Inspect the blower frequently for dirt buildup CHECKING/SERVICING BatteryHydrostatic Transmission Cooling Fins Electrolyte LevelCleaning the Terminals Mower Blade Profile For Sharpening Blade Balanced on Magnetic Wall-Mounted BalancerREPLACING/REPAIRING Spark PlugsREPLACING/REPAIRING Belt LocationsEngine PTO Drive Belt 3 Groove Power Band Engine PTO Drive Belt RemovalJackshaft Drive Belt Disengaged Jackshaft Drive Belt EngagedGHS Blower Drive Belt Assembly Engaged Hydrostatic Ground Drive Belt Assembly Disengaged Hydrostatic Ground Drive Belt Assembly EngagedFuel Shut-Off Valve and Filter Blade Overload Shear Bolts Fuel FilterFuel Filter Location Cutting Blade Shear BoltsMower Blades Remove Skid Bar for GHS Blower Removal GHS Blower Assembly and/or Blower WheelGHS Blower Assembly Removal Pressing Blower Wheel Out of Housing PTO Switch AdjustmentsSeat Switch PTO Clutch Engaged Blade Clutch PTOClutch Engagement/Belt Tension PTO Clutch Disengaged Blade Brake Band Adjustment PTO Belt Tightener Stop Block AdjustmentsClutch Idler Pulley Travel Adjustment Brake Actuator Rod Adjustment Set Forward Travel Limit Stop StepNeutral Function Adjustment Step Forward Speed Control Stop Steering Lever AdjustmentSteering Lever End Play Adjustment Step Neutral Function AdjustmentStraight Ground Travel Adjustment Step Tilt-Up Deck Adjustable Stop Troubleshooting When Horn Fails to Operate Carburetor AdjustmentGHS Full Signal Horn with Grass-Pak Switch Grass-PakSwitch Vane Adjustment Checking the Grass-PakSwitchAdjustment When Horn Sounds at the Wrong Time Circuit BreakersWiring Diagram Model MT Operator’s Notes Operator’s Notes Operator’s Notes Limited Warranty For Walker Commercial Rider Mower Sound Test Vibration Level

MT specifications

Walker, Montana, is a quaint and picturesque town nestled in the heart of the Treasure State. With a population of just under 2,000 residents, it possesses a unique charm that combines the beauty of nature with a tight-knit community atmosphere. The surrounding landscape boasts rolling hills and expansive fields, providing a stunning backdrop for outdoor enthusiasts seeking adventure or tranquility.

One of the main features of Walker is its commitment to sustainability and environmental conservation. The community is known for its efforts in promoting green technologies and practices. Many residents engage in eco-friendly farming, utilizing organic methods to cultivate the land and promote biodiversity. The town also actively participates in recycling programs and initiatives aimed at reducing waste, making it a great model for small-town sustainability.

Walker is a hub for modern technologies, with a focus on connecting residents to the digital world while preserving its historic roots. High-speed internet has become increasingly accessible, allowing local businesses to thrive and residents to enjoy the benefits of online connectivity. This digital shift has enabled the emergence of remote work opportunities and e-commerce, which has been pivotal for the local economy.

The town's infrastructure includes well-maintained roads and public transport options, ensuring ease of access for both residents and visitors. The local government has invested in smart city technologies, such as intelligent traffic management systems and energy-efficient street lighting, enhancing safety and improving quality of life.

Culturally, Walker celebrates its heritage through various events and festivals throughout the year. The annual Walker Fair showcases local artisans, musicians, and food vendors, creating a lively atmosphere that fosters community spirit. Education is also a priority, with schools emphasizing technological literacy and environmental awareness, preparing the next generation to thrive in a rapidly changing world.

Walker, Montana, stands out as a model small town that seamlessly blends nature, innovation, and community engagement. With its focus on sustainability, modern technologies, and rich cultural heritage, Walker offers a unique lifestyle that appeals to residents and visitors alike. Whether one seeks adventure in the great outdoors or the comforts of a close-knit community, Walker truly embodies the essence of Montana living.
Top Page Image Contents