Yazoo/Kees ZCBI48180 manual To Adjust the Deck Cutting Height See Fig

Page 13

OPERATION

NOTE: To begin motion the operator must be in the seat and the parking brake disengaged before the motion control levers can be moved from the neutral slots or the engine will kill. Fig. 4 and 4A.

By moving the levers an equal amount forward or back the machine will move in a straight line in that direction. Fig. 4 and 4A

Movement of either lever forward will cause the right or left wheel to rotate in a forward direction. To stop movement pull both levers into the neutral position.

To turn right while moving in a forward direction pull the right lever back towards the neutral position, this will slow the rotation of the right wheel and cause the machine to turn in that direction.

To turn left while moving in a forward direction pull the left lever back towards the neutral position, this will slow the rotation of the left

FORWARD

HEX NUTS AND WASHERS

CONTROL ARM

REVERSE

CONTROL

LEVER

NEUTRAL

SLOT

wheel and cause the machine to turn in that direction.

To zero turn pull one lever back beyond neutral while holding the other slightly ahead of neutral.

NOTE: The direction of the zero turn will be determined by which lever is pulled back beyond neutral. Thus left lever back, left zero turn and opposite for right zero turn.

Use extra care when using this maneuver the machine can spin very rapidly if one lever is positioned to far ahead of the other.

CAUTION

DO NOT apply excessive force to control levers or use to assist in dismounting unit. Misuse will result in bent control levers.

FIGURE 4A

TO ADJUST THE DECK CUTTING HEIGHT (See Fig. 5)

The deck cutting height is obtained by pressing the foot pedal forward to lift the deck. To lower the deck, you apply pressure to the top side of the foot pedal and allow it to pivot while allowing the lift arm to rotate to the rear of the unit. To stop in a desired cutting position, rotate the foot pedal down into the notch in the height plate. The cutting height range is from 1 1/2" to 4 1/2" in 1/2" increments. The heights are measured from the ground up to the blade tip with the engine not running.

The average lawn should be cut to 2 1/2" during the cool season and to over 3" during the hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to the desired height.

13

Image 13
Contents ZCBI48180 Operators Manual ModelsGood Service Contents General Operation Safety RulesII. Slope Operation Safe Operation Practices for RIDE-ON MowersIII. Children III. ServiceSafe Operation Practices for RIDE-ON Mowers Do not Safety Rules Customer Responsibilities SpecificationsTools Required For Assembly AssemblyTo Remove the Mower from Crate Before Removing Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Check the Tire Pressure ChecklistControls OperationIZT Integrated Zeroturn Transaxle Bypass Linkages Deck Blades HOW to USE Your MowerEngine To Adjust the Deck Cutting Height See Fig Rollers See Figure To Adjust ANTI-SCALPTo Operate Mower To Operate on HillsTo Transport See Fig To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Maintenance ScheduleBefore Each USE Operator Presence System Lubrication ChartBlade Care TiresTo Sharpen Blade See Fig BatteryClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts EngineAIR Filter CleaningEngine OIL Filter Spark PlugsBefore Performing ANY Service or Adjustments Service and AdjustmentMower To Level DeckTo Replace Deck Belt To Replace IZT Integrated Zeroturn Transaxle Belt See Fig To Adjust Control Levers See Fig To Adjust the Seat See FigTo Remove Wheels for Repair Jump Starting EngineTo Adjust Park Brake Replacing Battery See FigTracking Adjustment Storage BatteryFuel System Engine OILCylinders OtherProblem Cause Correction Troubleshooting PointsAttachment Poor cut uneven ProblemcausecorrectionWiring Schematic