Yazoo/Kees ZCBI48180 manual Control Lever ARM HEX Bolts Neutral Slot

Page 9

ASSEMBLY

Adjustments may be required to get uniform positioning of the control lever. Refer to the "Service and Adjustment" section of this manual.

NOTE: You may now roll or drive the mower off of the skid. Follow the appropriate instruction below to remove the mower from the skid.

CONTROL

LEVER

CONTROL

ARM

HEX

BOLTS

NEUTRAL

SLOT

FIGURE 2

TO ROLL THE MOWER OFF OF THE SKID (See Operation section for location and function of controls

•Move to the rear of the mower, and place the IZT (Integrate Zeroturn Transaxle) bypass linkages into the bypass position to disengage the IZT’s (See “TO TRANSPORT” in the Operation section of this manual).

•Sitting on the mower, press the deck lift pedal in to the highest cutting position.

•Release park brake lever.

•Roll the mower forward or backward off of the skid.

TO DRIVE THE MOWER OFF OF THE SKID (See Operation section for location and function of controls)

WARNING

Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure the mower is in a well-ventilated area. Be sure the area in front of the mower is clear of other people and objects.

•Be sure all of the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place the IZT(Integrated Zeroturn Transaxle) bypass linkages into the drive position (See “TRANSPORT” in the Operation section of this manual).

•Sit on the seat in the operating position, set the park brake lever to the on position.

•Rotate the control levers outward into the neutral slot.

•Press forward on the deck lift pedal to raise the deck into the highest cutting position.

•Pull choke cable knob up.

•Start the engine. After the engine has started, push choke cable knob down.

•Release the park brake.

•Move the control levers into the operate position.

•Slowly move the control levers forward and slowly drive the mower off of the skid.

•Return the control levers back to the neutral position.

•Apply the park brake.

•Turn the ignition key to the “OFF” position.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents ZCBI48180 Operators Manual ModelsGood Service Contents General Operation Safety RulesII. Slope Operation Safe Operation Practices for RIDE-ON MowersIII. Service III. ChildrenSafe Operation Practices for RIDE-ON Mowers Do not Safety Rules Customer Responsibilities SpecificationsTools Required For Assembly AssemblyTo Remove the Mower from Crate Before Removing Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Check the Tire Pressure ChecklistOperation ControlsIZT Integrated Zeroturn Transaxle Bypass Linkages HOW to USE Your Mower Deck BladesEngine To Adjust the Deck Cutting Height See Fig Rollers See Figure To Adjust ANTI-SCALPTo Operate Mower To Operate on HillsTo Transport See Fig To Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Maintenance Schedule General RecommendationsBefore Each USE Operator Presence System Lubrication ChartBlade Care TiresTo Sharpen Blade See Fig BatteryClean AIR INTAKE/COOLING Areas Clean AIR ScreenBelts EngineAIR Filter CleaningEngine OIL Filter Spark PlugsBefore Performing ANY Service or Adjustments Service and AdjustmentMower To Level DeckTo Replace Deck Belt To Replace IZT Integrated Zeroturn Transaxle Belt See Fig To Adjust Control Levers See Fig To Adjust the Seat See FigTo Remove Wheels for Repair Jump Starting EngineTo Adjust Park Brake Replacing Battery See FigTracking Adjustment Storage BatteryFuel System Engine OILCylinders OtherProblem Cause Correction Troubleshooting PointsAttachment Poor cut uneven ProblemcausecorrectionWiring Schematic
Top Page Image Contents