Yazoo/Kees ZCBI48180 Before Starting the Engine, To Start Engine See Fig, Check Engine OIL Level

Page 16

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your mower has been shipped from the factory, already filled with 10W-30 motor oil.

•Check engine oil with the mower on level ground.

•Refer to you Engine Owners Manual for correct oil level.

•To change engine oil, see the Customer Responsibilities section of this manual.

ADD GASOLINE

•Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to ensure fuel freshness.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32° F. (0° C.), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION

Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids dur- ing storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it the run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instruc- tions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.

WARNING

Fill to bottom of filler neck. Do not over fill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure IZT (Integrated Zeroturn Transaxle) bypass linkages are in the drive position.

•Sit on the seat in the operators position, release park brake lever.

•Check to be sure the PTO switch is disengaged.

•Pull choke cable knob up.

•For a warm engine start, the choke control may not be needed

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operators Manual Models ZCBI48180Good Service Contents Safety Rules General OperationII. Slope Operation Safe Operation Practices for RIDE-ON MowersIII. Children III. ServiceSafe Operation Practices for RIDE-ON Mowers Do not Safety Rules Specifications Customer ResponsibilitiesAssembly Tools Required For AssemblyTo Remove the Mower from Crate Before Removing Mower from the SkidControl Lever ARM HEX Bolts Neutral Slot Checklist Check the Tire PressureControls OperationIZT Integrated Zeroturn Transaxle Bypass Linkages Deck Blades HOW to USE Your MowerEngine To Adjust the Deck Cutting Height See Fig To Adjust ANTI-SCALP Rollers See FigureTo Operate Mower To Operate on HillsTo Transport See Fig Before Starting the Engine To Start Engine See FigCheck Engine OIL Level ADD GasolineMowing Tips General Recommendations Maintenance ScheduleBefore Each USE Lubrication Chart Operator Presence SystemBlade Care TiresBattery To Sharpen Blade See FigClean AIR Screen Clean AIR INTAKE/COOLING AreasBelts EngineCleaning AIR FilterEngine OIL Filter Spark PlugsService and Adjustment Before Performing ANY Service or AdjustmentsMower To Level DeckTo Replace Deck Belt To Replace IZT Integrated Zeroturn Transaxle Belt See Fig To Adjust the Seat See Fig To Adjust Control Levers See FigTo Remove Wheels for Repair Jump Starting EngineReplacing Battery See Fig To Adjust Park BrakeTracking Adjustment Battery StorageFuel System Engine OILOther CylindersTroubleshooting Points Problem Cause CorrectionProblemcausecorrection Attachment Poor cut unevenWiring Schematic
Top Page Image Contents