Yazoo/Kees ZCBI48180 manual Replacing Battery See Fig, To Adjust Park Brake

Page 27

SERVICE AND ADJUSTMENT

TO ATTACH JUMPER CABLES

•Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from the fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

REPLACING BATTERY (See Fig. 18)

WARNING

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal brace- lets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.

•Tighten securely.

•Close terminal access doors.

•Lower seat.

TERMINAL

GUARD

TERMINAL

ACCESS

DOORS

FIGURE 18

TO ADJUST PARK BRAKE

Before making any adjustments:

NOTE: Make sure the brake arm is engaged into brake sprocket on both sides. You can push the mower to make it engage into the sprocket. See Fig. 19.

•With the park brake in the on position, the compression spring should be 2" from the "U" shaped brake arm to the washer. See Fig. 19. If not, use two wrenches, one to hold the bolt and one to turn the nut to attain the 2".

• Lift Seat and rotate forward.

• Open terminal access doors.

• Using two 1/2" wrenches disconnect

BLACK battery cable then RED battery

cable.

• Using 7/16" wrench, remove terminal

guard.

• Carefully remove the battery from the

mower.

• Install new battery with terminals in the

same position as the old battery.

• Reinstall terminal guard

• First connect RED battery cable to

positive (+) battery terminal with hex bolt

SPRING

ADJUSTMENT

NUT

BRAKE

COMPRESSION

SPRING

BRAKE

 

 

 

IZT BRAKE

SPROCKET

 

 

ARM

RIGHT SIDE

 

 

RIGHT SIDE

 

 

"U" SHAPED BRAKE ARM

and hex nut.

FIGURE 19

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents ZCBI48180 Operators Manual ModelsGood Service Contents Safe Operation Practices for RIDE-ON Mowers Safety RulesGeneral Operation II. Slope OperationIII. Service III. ChildrenSafe Operation Practices for RIDE-ON Mowers Do not Safety Rules Customer Responsibilities SpecificationsBefore Removing Mower from the Skid AssemblyTools Required For Assembly To Remove the Mower from CrateControl Lever ARM HEX Bolts Neutral Slot Check the Tire Pressure ChecklistOperation ControlsIZT Integrated Zeroturn Transaxle Bypass Linkages HOW to USE Your Mower Deck BladesEngine To Adjust the Deck Cutting Height See Fig To Operate on Hills To Adjust ANTI-SCALPRollers See Figure To Operate MowerTo Transport See Fig ADD Gasoline Before Starting the EngineTo Start Engine See Fig Check Engine OIL LevelMowing Tips Maintenance Schedule General RecommendationsBefore Each USE Tires Lubrication ChartOperator Presence System Blade CareTo Sharpen Blade See Fig BatteryEngine Clean AIR ScreenClean AIR INTAKE/COOLING Areas BeltsSpark Plugs CleaningAIR Filter Engine OIL FilterTo Level Deck Service and AdjustmentBefore Performing ANY Service or Adjustments MowerTo Replace Deck Belt To Replace IZT Integrated Zeroturn Transaxle Belt See Fig Jump Starting Engine To Adjust the Seat See FigTo Adjust Control Levers See Fig To Remove Wheels for RepairTo Adjust Park Brake Replacing Battery See FigTracking Adjustment Engine OIL BatteryStorage Fuel SystemCylinders OtherProblem Cause Correction Troubleshooting PointsAttachment Poor cut uneven ProblemcausecorrectionWiring Schematic
Top Page Image Contents