Yazoo/Kees ZCBI48180 manual Lubrication Chart, Operator Presence System, Blade Care, Tires

Page 19

CUSTOMER RESPONSIBILITIES

LUBRICATION CHART

GREASE LUBE POINTS EVERY 25 HOURS.

CHECK TIRE AIR PRESSURE

FRONT TIRES - 15 PSI

REAR TIRES - 15 PSI

REFER TO ENGINE OPERATORS MANUAL PRIOR TO SERVICING THE ENGINE.

IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUSTAND DIRT THAT WILL SHORTEN THE LIFE OFTHE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANTSPARINGLY.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure the operator presence and interlock systems are working properly. If your mower does not function as described, repair the problem immediately.

•The engine should not start unless the parking brake is engaged, the PTO switch is disengaged (pressed down), the operator is on the seat, and the control levers are rotated to the outside of the mower.

•When the engine is running, any attempt by the operator to leave the seat without first setting the park brake should shut off the engine.

•When the engine is running and the PTO switch is engaged, any attempt by the operator to leave the seat without first disengaging the PTO switch, should shut off the engine.

•When the engine is running and the control levers are rotated in, any attempt by the operator to leave the seat without rotating the control levers out, should shut off the engine.

•The PTO switch should never engage without the operator on the seat.

BLADE CARE

For best results, mower blades must be kept sharp. Replace bent or damage blades.

TIRES

•Maintain proper air pressure in all tires (See "SPECIFICATIONS" section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE REMOVAL (See Fig. 8)

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or re-sharpened blade with stamped "THIS SIDE UP" facing deck and cutter housing.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents ZCBI48180 Operators Manual ModelsGood Service Contents Safe Operation Practices for RIDE-ON Mowers Safety RulesGeneral Operation II. Slope OperationIII. Children III. ServiceSafe Operation Practices for RIDE-ON Mowers Do not Safety Rules Customer Responsibilities SpecificationsBefore Removing Mower from the Skid AssemblyTools Required For Assembly To Remove the Mower from CrateControl Lever ARM HEX Bolts Neutral Slot Check the Tire Pressure ChecklistControls OperationIZT Integrated Zeroturn Transaxle Bypass Linkages Deck Blades HOW to USE Your MowerEngine To Adjust the Deck Cutting Height See Fig To Operate on Hills To Adjust ANTI-SCALPRollers See Figure To Operate MowerTo Transport See Fig ADD Gasoline Before Starting the EngineTo Start Engine See Fig Check Engine OIL LevelMowing Tips General Recommendations Maintenance ScheduleBefore Each USE Tires Lubrication ChartOperator Presence System Blade CareTo Sharpen Blade See Fig BatteryEngine Clean AIR ScreenClean AIR INTAKE/COOLING Areas BeltsSpark Plugs CleaningAIR Filter Engine OIL FilterTo Level Deck Service and AdjustmentBefore Performing ANY Service or Adjustments MowerTo Replace Deck Belt To Replace IZT Integrated Zeroturn Transaxle Belt See Fig Jump Starting Engine To Adjust the Seat See FigTo Adjust Control Levers See Fig To Remove Wheels for RepairTo Adjust Park Brake Replacing Battery See FigTracking Adjustment Engine OIL BatteryStorage Fuel SystemCylinders OtherProblem Cause Correction Troubleshooting PointsAttachment Poor cut uneven ProblemcausecorrectionWiring Schematic
Top Page Image Contents