Yazoo/Kees ZVKW52253, ZVKH61273 manual Hour Meter, Tracking knob, Parking Brake, Controls

Page 20
2. Hour Meter

CONTROLS

2. Hour Meter

The hour meter displays the total operating time.

It will flash CHG OIL (Change Oil) at 50 hour intervals. The flash duration is one hour before and one hour after the interval. The CHG OIL icon will come on and shut off automatically. The hour meter can not be manually reset.

3. Tracking knob

The tracking knob is located in front of the left control lever. Rotating this knob allows fine tuning adjustments so that the machine tracks straight with the drive levers in the full forward position.

Rotate the knob clockwise (as viewed from the operating position) to increase the speed or counter clockwise to decrease the speed on the left control lever. Example: If control levers are full forward and the unit turns to the right, turn the tracking knob counter clockwise to decrease the speed on the left control lever.

hour meter

Hour meter

8011-442

Tracking knob

4. Parking Brake

The parking brake is found on the left of the machine. Pull the lever backward to activate the brake and forward to release it.

8011-511

Parking brake not activated

English-18

Image 20
Contents Operator Manual English   Page Contents OPERATOR’S MANUAL RIDER MAX 2 SERIESEnglish-2 INTRODUCTION IntroductionCongratulations GeneralGood Service Manufacturing NumberSYMBOLS AND DECALS Symbols and DecalsRead General Operation SAFETY INSTRUCTIONSSafety Instructions English-8 Personal Safety Equipment Slope OperationChildren Maintenance General Maintenance Use protective goggles Transport Roll over Protection system ROPS Customer responsibilitiesControl Locations CONTROLSControls 4Reverse 1. Motion Control Levers1Forward 2Neutral 3Neutral slot, Neutral lock 4. Parking Brake 2. Hour Meter3. Tracking knob 7. Fuses 5. Blade switch6. Ignition Switch 8. Seat Locking Device 9. Refueling12. Choke Control 11. Seat Adjustment Lever10. Fuel Shut Off Valve 13. Throttle Control 14. Lifting Lever for the Mower DeckAccessories Cutting height pedalPump release valves Tighten the valve moderatelyTraining OPERATIONOperation Starting the Engine Roll bar and safety beltBefore Starting 6.Move the throttle to the middle position 8.Open the fuel valve for the selected fuel tank OPERATION To start an engine with a weak battery Running Operating on hills Mowing Tips Mowing patternsStopping the Engine Moving by Hand Vent screw on the hydraulic pumpEnglish-34 8011-507Maintenance Schedule MAINTENANCEMaintenance The parking brake is on The engine is stoppedThe ignition key has been removed Battery Ignition System Checking the Safety System Safety system Ignition systemEnglish-40 8011-553Checking the Engines Cooling Air Intake Checking and Adjusting the Throttle CableChecking and Adjusting the Choke Cable Air filter maintenance Filter replacement Air filter indicator optionalReplacing the Fuel Filter Checking the Fuel Pump’s Air FilterChecking Tire Pressures Checking the Parking BrakeChecking the V-belts Faulty adjustment can cause an accidentChecking the Blades Pump beltBlade replacement Adjusting the Mower Deck Engine oil cooler To adjust anti-scalprollersCleaning and Washing Caster WheelsHardware Use protective glasses when cleaning and washingLubrication Schedule LUBRICATIONLubrication Lubricating the Cables Shaft Bushings and Linkage1. Hydraulic System, Oil Level Changing Oil and FiltersLUBRICATION Checking the Oil Level Oil Recommendations LUBRICATION 4.Throttle and Choke Cables, Lever Bearings 5. Front Wheel Mount7. Deck belt pulleys 8. Mower Deck Height Adjuster6. Front Wheel Bearings 9.Steering Control Shafts Tip the driver’s seat 10. Mower Deck StrutsLubricating the steering control shafts Lubricating struts11. Changing the Oil Filter TROUBLE SHOOTING GUIDE Trouble Shooting GuideWrong fuel type Uneven mowing results Service STORAGEStorage Winter StorageTECHNICAL DATA Technical DataProductivity Overall dimensionsEquipment ZVKH61303 ZVKH72303TECHNICAL DATA Accessories Torque SpecificationsUSA requirements CONFORMITY CERTIFICATESConformity Certificates Delivery Service SERVICE JOURNALService Journal After the First 8 Hours 25-HourService 4.Lubricate the belt adjuster, mower deck5.Lubricate the belt adjuster, hydraulic pumps 6.Check/clean the engine’s cooling air intake50-HourService 1.Perform the 25-hourservice5.Lubricate the cutting height adjuster 6.Check/adjust the parking brake100-HourService 300-HourService At Least Once Each Year English-78 Date, mtr reading, stamp, sign SERVICE JOURNALAction Date, mtr reading, stamp, sign SERVICE JOURNALAction Page 539 131260 IR 07/07
Related manuals
Manual 84 pages 62.74 Kb