North Star M268180M Operation Preparing the Sprayer for Each Use, Important safety rules

Page 20

Operation – Preparing the Sprayer for Each Use

If the sprayer has been used previously, it must be prepared BEFORE EACH SUBSEQUENT USE.

WARNING

Read instructions below carefully for inspecting and preparing the sprayer. Damaged or clogged equipment could result in leaks or uncontrolled spray.

Leaks could result in injury to the operator or bystanders from chemical exposure, or cause damage to the environment.

Important safety rules:

•Power off. Make sure all power is OFF before cleaning, inspecting, or servicing the sprayer.

•Guards / shields. Make sure all guards and shields are replaced after servicing the sprayer.

•Replacement parts. If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement parts that do not meet specifications may result in a safety hazard or poor operation of the sprayer.

1.

Ensure sprayer

Ensure the sprayer is securely attached to the vehicle.

 

attached

 

 

2.

Ensure tank

Ensure the sprayer has been thoroughly flushed and drained of all residual

 

empty

chemical from prior uses.

3. Clean suction

Clean the suction strainer of any chemical residue.

 

strainer

It is important to clean the suction strainer before each use to ensure it is not

 

 

clogged and to prevent residual chemical from contaminating sprayer contents.

 

 

IMPORTANT: The strainer must be accessed by reaching into the tank, so the

 

 

tank must be empty to avoid immersing your hand in chemicals.

 

 

a) Open fill cap on top of tank.

 

 

b)

USING RUBBER GLOVES, reach into the tank and pull the suction

 

 

 

strainer off the end of the suction tube. (See figure below.)

 

 

c)

Run the suction strainer under fresh water to remove debris.

 

 

d)

Replace the suction strainer onto the end of the suction tube.

 

 

 

Fill cap

 

),*

 

Suction strainer

 

(Inside tank)

4. Inspect &

Inspect and test the sprayer thoroughly:

repair

a) Inspect hoses for exposed mesh and holes. Replace all worn or damaged hoses.

b)Inspect fittings for cracks and leaks. Replace all damaged fittings with original NorthStar parts.

c)Inspect tank for cracks.

d)Check to be sure all nuts, bolts, and screws are tight.

e)Partially fill tank with plain water and spray to test for leaks. Repair as needed.

IMPORTANT: After any repair work has been done, ALWAYS test for leaks with water one final time before using.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents M268180M Hazard Signal Word Definitions Table of Contents Intended Use Spraying PesticidesChemical Application Safety Summary of Important Safety InformationGeneral Chemical Safety Chemical Accident Procedures ATV Vehicle Handling Safety Following items are found in the manual bag Closely inspect all contents in the shipping cartonUnpacking Assembly Step One Attach gaugeStep Two Attach gun hose to spray gun and pump Step Three Attach gun clips to tankStep Five Attach hose guide to tank Step Six Attach sprayer to vehicleStep Seven Connect power cords to vehicle battery Preparatory safety Preparatory safety stepsSeparate power Prepare wire endsVehicle battery To install battery clampsAttach remote switch TogetherStep Eight Check and test completed assembly Check and test completed assemblyCheck assembly Working conditionMachine Components Operation Important Safety Information General Chemical SafetyChemical Application Safety Before SprayingDuring Spraying After SprayingATV Vehicle Handling Safety Inhalation To be automatically linked to the nearest certified poisonImportant safety rules Operation Preparing the Sprayer for Each UseSpray because the wind is too strong Operation Using the SprayerStep One Assess wind conditions and clear work area Ensure tank is flushed of all chemicals from prior uses Fill the sprayer using the following stepsStep Two Fill the sprayer Check drain Fill tankReview safety Turn on powerStep Three Operate the sprayer Ensure flowProper Operation of the Spray Gun Operate spray gun as needed for applicationOpen until desired amount of agitation is achieved ImmediatelyStep Four Clean sprayer and decontaminate after use Drain tankDecontaminate LaunderRemoving from storage StoragePreparing for storage Troubleshooting Before attempting to service the sprayerSpecifications Any Questions, Comments, Problems or Parts OrdersExploded View 268180 Rev. M Part# Description

M268180M specifications

The North Star M268180M is a robust and versatile utility vehicle designed to meet the demands of various industries, including agriculture, construction, and outdoor recreational activities. This model is recognized for its unique blend of power, efficiency, and durability, which make it an ideal option for users seeking a reliable companion for their demanding tasks.

One of the standout features of the M268180M is its powerful engine, which provides robust performance across a range of terrains. The vehicle is equipped with a high-efficiency diesel engine that ensures low fuel consumption while delivering substantial torque. This makes it not only economical to operate but also capable of tackling heavy loads and challenging landscapes with ease.

The M268180M boasts advanced off-road capabilities, thanks to its impressive four-wheel-drive system and superior suspension design. This enables the vehicle to navigate rough and uneven terrain without compromising on comfort or stability. The all-terrain tires provide excellent grip, ensuring that the M268180M can handle mud, sand, and rocky surfaces without difficulty.

In terms of technology, the North Star M268180M is equipped with a user-friendly dashboard that provides essential information at a glance, enhancing the driver's control over the vehicle. Additionally, it features advanced safety systems, including robust braking mechanisms and roll-over protection, ensuring that operators can work safely even in challenging conditions.

Comfort is another key aspect of the M268180M, which is designed with ergonomically crafted seating and ample cabin space. The interior accommodates the driver and passenger comfortably, allowing for long hours of use without fatigue. Furthermore, it offers easy access and excellent visibility, making navigation simple and intuitive.

Durability is paramount in the design of the M268180M, which features a rugged frame and reinforced body to withstand the pressures of heavy-duty use. Its materials are chosen to resist wear and tear, ensuring longevity and reliability in various operating environments.

In summary, the North Star M268180M stands out with its powerful engine, advanced off-road capabilities, user-friendly technology, comfort-focused design, and exceptional durability. This utility vehicle is an excellent choice for those seeking a dependable, high-performance machine to handle their most demanding tasks efficiently.
Top Page Image Contents