North Star M268180M owner manual Chemical Accident Procedures, ATV Vehicle Handling Safety

Page 6

Summary of Important Safety Information (continued)

•ALWAYS HOLD THE SPRAY GUN FIRMLY when spraying at higher pressures to prevent gun from whipping. Keep good footing and balance at all times.

•EXERCISE EXTRA CAUTION when spraying near areas accessible to children and pets.

•CLEAN up spills immediately per instructions on the chemical label.

•TURN OFF vehicle and set brake or block wheels, TURN OFF power to sprayer, and RELIEVE system pressure before leaving sprayer unattended.

•SEE Troubleshooting section of this manual before attempting any repairs. Wear personal protective equipment and follow safety instructions.

After Spraying

•CLEAN sprayer immediately after use according to the directions provided in this manual.

•DECONTAMINATE yourself after you are done spraying and have cleaned the sprayer. Wash all exposed areas of the body with soap and water, and remove and launder clothing.

•DISPOSE OF or STORE remaining chemicals in secure storage with correctly marked container.

ATV Vehicle Handling Safety

•DO NOT ALLOW drivers younger than 16 to operate ATV with sprayer attached.

•EXERCISE SPECIAL CAUTION in ATV vehicle handling and DO NOT exceed 5 MPH. ATV will be less stable and perform very differently with filled sprayer attached. Exercise particular caution on sloped or rough surfaces to avoid rollover. Use a vehicle equipped with rollover protection for use on non-level terrain.

•DO NOT RIDE or TRANSPORT cargo on the sprayer.

Chemical Accident Procedures

Immediate response is necessary in the event of sprayer leaks, bodily chemical contact, poisoning, or spills. See instructions below:

Sprayer leak

If the sprayer develops a leak, immediately stop spraying. Turn off power to the sprayer

 

and follow directions below, as applicable.

Bodily chemical

Personal contamination can occur when chemicals splash, spill, or spray directly onto a

contact

person.

 

1.

Immediately follow First Aid instructions on chemical label.

 

 

General procedures can include:

 

 

a) Eyes – immediately flush with water.

 

 

b) Skin – wash all contaminated skin surfaces with soap and water.

 

 

c) Clothing – remove contaminated clothing. Dispose of heavily contaminated

 

 

clothing per chemical label instructions.

 

2.

Seek medical advice if instructed on the label or the victim experiences symptoms of

 

 

harmful effects. Bring the chemical label for reference.

Poisoning by

In case of poisoning from ingestion or inhalation:

ingestion or

If the victim has collapsed or is not breathing, call 911. Otherwise:

inhalation

1.

If you are the victim, immediately seek assistance from nearby personnel because you

 

 

 

may become incapacitated.

 

2.

Immediately follow first aid instructions on chemical label.

 

3.

Call a poison control center for further advice. In the U.S., call 1-800-222-1222.Have

 

 

the chemical label available for reference.

Chemical spills

Chemical spills must be quickly contained and properly cleaned up.

 

Refer to the chemical label for any specific clean-up instructions.

General procedures include:

1.Controlling the spill by stopping the source of the spill.

2.Containing the spill so that it does not spread and get into water sources.

3.Cleaning up the spill immediately.

4.Seeking additional advice from:

-Chemical manufacturer. See chemical label for contact information.

-State pesticide regulatory agency. In the U.S., call the National Pesticide Info. Ctr. at

800-858-7378 for assistance in contacting your state’s agency.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents M268180M Hazard Signal Word Definitions Table of Contents Intended Use Spraying PesticidesSummary of Important Safety Information General Chemical SafetyChemical Application Safety Chemical Accident Procedures ATV Vehicle Handling Safety Closely inspect all contents in the shipping carton UnpackingFollowing items are found in the manual bag Step Two Attach gun hose to spray gun and pump AssemblyStep One Attach gauge Step Three Attach gun clips to tankStep Five Attach hose guide to tank Step Six Attach sprayer to vehicleStep Seven Connect power cords to vehicle battery Preparatory safety Preparatory safety stepsVehicle battery Separate powerPrepare wire ends To install battery clampsAttach remote switch TogetherCheck assembly Step Eight Check and test completed assemblyCheck and test completed assembly Working conditionMachine Components Operation Important Safety Information General Chemical SafetyDuring Spraying Chemical Application SafetyBefore Spraying After SprayingATV Vehicle Handling Safety Inhalation To be automatically linked to the nearest certified poisonImportant safety rules Operation Preparing the Sprayer for Each UseOperation Using the Sprayer Step One Assess wind conditions and clear work areaSpray because the wind is too strong Fill the sprayer using the following steps Step Two Fill the sprayerEnsure tank is flushed of all chemicals from prior uses Check drain Fill tankStep Three Operate the sprayer Review safetyTurn on power Ensure flowProper Operation of the Spray Gun Operate spray gun as needed for applicationOpen until desired amount of agitation is achieved ImmediatelyDecontaminate Step Four Clean sprayer and decontaminate after useDrain tank LaunderStorage Preparing for storageRemoving from storage Troubleshooting Before attempting to service the sprayerSpecifications Any Questions, Comments, Problems or Parts OrdersExploded View 268180 Rev. M Part# Description

M268180M specifications

The North Star M268180M is a robust and versatile utility vehicle designed to meet the demands of various industries, including agriculture, construction, and outdoor recreational activities. This model is recognized for its unique blend of power, efficiency, and durability, which make it an ideal option for users seeking a reliable companion for their demanding tasks.

One of the standout features of the M268180M is its powerful engine, which provides robust performance across a range of terrains. The vehicle is equipped with a high-efficiency diesel engine that ensures low fuel consumption while delivering substantial torque. This makes it not only economical to operate but also capable of tackling heavy loads and challenging landscapes with ease.

The M268180M boasts advanced off-road capabilities, thanks to its impressive four-wheel-drive system and superior suspension design. This enables the vehicle to navigate rough and uneven terrain without compromising on comfort or stability. The all-terrain tires provide excellent grip, ensuring that the M268180M can handle mud, sand, and rocky surfaces without difficulty.

In terms of technology, the North Star M268180M is equipped with a user-friendly dashboard that provides essential information at a glance, enhancing the driver's control over the vehicle. Additionally, it features advanced safety systems, including robust braking mechanisms and roll-over protection, ensuring that operators can work safely even in challenging conditions.

Comfort is another key aspect of the M268180M, which is designed with ergonomically crafted seating and ample cabin space. The interior accommodates the driver and passenger comfortably, allowing for long hours of use without fatigue. Furthermore, it offers easy access and excellent visibility, making navigation simple and intuitive.

Durability is paramount in the design of the M268180M, which features a rugged frame and reinforced body to withstand the pressures of heavy-duty use. Its materials are chosen to resist wear and tear, ensuring longevity and reliability in various operating environments.

In summary, the North Star M268180M stands out with its powerful engine, advanced off-road capabilities, user-friendly technology, comfort-focused design, and exceptional durability. This utility vehicle is an excellent choice for those seeking a dependable, high-performance machine to handle their most demanding tasks efficiently.
Top Page Image Contents