Multiquip LT6D Inspection, Engine Servicing, Light tower inspection, Engine Oil Check

Page 27

inspection

Engine Servicing

The diesel engine (Figure 7) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer’s engine manual for instructions and details of operation and servicing.

light tower inspection

Check or do the following:

„„Clean the light tower, removing dirt and dust, particularly the engine cooling air inlet and air cleaner.

„„Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.

„„Check all fastening nuts and bolts for tightness.

„„Check winch cables, make sure they are not frayed or defective. Replace any defective or worn winch cables.

WARNING

DO NOT use light tower if winch cables are worn or defective. Replace defective cables immediately.

Engine Oil Check

To check the engine oil level, make sure the light tower is placed on secure level ground with the engine stopped.

1.Remove the dipstick from its holder and wipe it clean.

2.Insert and remove the dipstick from its holder. Check the oil level shown on the dipstick.

3.If the oil level is low, add oil through the oil filler hole. DO NOT overfill. Fill to the normal operating level as shown on the dipstick. Verify that the oil level is maintained between the two notches as shown in Figure 8. Always fill with recommended type oil as listed in Table 4. See Table 2 for engine oil capacity.

Table 4. Recommended Motor Oil

(Kohler Engines)

°C -40

-35

-30

-25

-20

-15

-10

-5

0

5

10

15

20

25

30

35

40 45 50

°F -40

-31

-22

-13

-4

5

14

23

32

41

50

59

68

77

86

95

104 113 122

SAE 10W

SAE 20W

SAE 30

SAE 40

SAE 10W-30

SAE 10W-40

SAE 10W-60

Other types of motor oils may be substituted if they meet the following requirements:

„„API Service Classification CH-4

„„API Service Classification CG-4

„„API Service Classification CF-4 „„ACEA Specification E3 „„ACEA Specification E2

Figure 8. Oil Dipstick

LT6D LIGHT TOWER • operation manual — rev. #0 (07/16/13) — page 27

Image 27
Contents Model LT6D Proposition 65 warning Nhtsa Reporting Safety DefectsLT6D Light Tower Table of ContentsAddresses practices not related to personal injury Safety InformationSaFeTY messages SaFeTY sYmBOLsfirst aid kit GeneRaL saFeTY„ Always know the location of the nearest fire extinguisherLamp saFeTY Light Tower SafetyAny enclosed or narrow area EngIne saFeTY„ neveR tamper with the factory settings „ The engine of this equipmentFrom fuel vapors or if fuel is spilled on a hot engine FueL saFeTYTOWIng saFeTY „ neveR use fuel as a cleaning agentLoading and Tie-Down on Flatbed Truck TRanspORTIng saFeTY„ neveR use gas piping as an electrical ground ELeCTRICaL saFeTYPower Cord/Cable safety Grounding SafetyEnvIROnmenTaL saFeTY/DeCOmmIssIOnIng BaTTeRY saFeTYEmIssIOns InFORmaTIOn Emission Control LabelLabel must remain with the engine for its entire life Lamp Footcandle Plot Lamp footcandle plotLT6D Specifications Generator SpecificationsTrailer Specifications Engine Specifications Dimensions DimensionsReference Letter Description Dimension Metal Halide Lamps General informationPage Major Components 1 Control Panel Side ComponentsMajor Components 2 Control Panel Side Major Components Front/ Rear Page Control panel Control Panel/Ignition SwitchLED green lights when the engine is OK functioning normal Normal Operation Indicator This alarmKohler Engine Components Engine componentsEngine Oil Check InspectionEngine Servicing Light tower inspectionBattery Check Fuel CheckWipe up any spilled fuel immediately Operation in Freezing Weather Cleaning the RadiatorAir Cleaner Fan Belt Tension CoolantLight Power Cable Connections SetupIndoor Installation Lamp power cable connectionsLight tower grounding Outriggers and Support StandsLight tower from rolling Mast Operation Deploying the Mast Vertical Position Extending the MastRotating the Mast Operation Starting the EngineTurning On the Lights VAC Gfci Receptacle Testing the 120 VAC Gfci ReceptacleApplying an External Load 120/240 VAC Twist-Lock ReceptacleFrequency MaintenanceBasic Inspection and Maintenance Inspection/MaintenanceOFF position Air CleanerClean the inside of the cover using a damp cloth General InspectionFuel Addition Service DailyCleaning the Fuel Strainer Replacing Fuel FilterFlushing Out Radiator and Changing Coolant Lamp ReplacementOil Filter Cartridge 200 Hours BeltCheck Cable Wear Servicingthe Mast Raise/Lower Cable SystemReplace the pulley and the cable as needed Lower the mast to the horizontal resting position Servicingthe Mast Extension Cable SystemStorage Removal From Long Term StorageType Part Number Maintenance TrailersAdjustable Channel Trailer CouplersLeaf Suspension Wheel Hub AdjustmentTRaILeR TOWIng guIDeLInes COmmOn Causes for LOss of TRaILeRCOupLIng to THe TOW veHICLe DRIvIng COnDITIOnsInOpeRaBLe BRaKes, LIgHTs or mIRRORs TRaILeR TOWIng TIpsTRaILeR vIn Tag SIDe vIeW mIRRORs ELeCTRICaL COnneCTORTOW veHICLe SuspensIOn sYsTemBaLL COupLeR SaFeTY CHaInsJaCKsTanD COupLeR TYpesLock washer and hitch frame Before coupling trailer, inspect the hitch ball for wearAttaching safety Chain Connecting Trailer LightsUncoupling the Ball Hitch Pintle Coupler and pintle Hook PInTLe COupLeRCoupling Trailer to Tow vehicle pintle Coupler Unsafe Tires, Lug nuts or WheelsBe sure lug nuts are tight before each tow Determining Load Limit of TrailerStep Tighten lug nuts before each towDetermining Load Limit of Tow vehicle step TIRe FunDamenTaLsP indicates the tire is for passenger vehicles Uniform Tire Quality grading standards uTQgs Table a. Speed RatingLetter Rating Speed Rating Replacing Worn or Damaged Tires Tire Safety TipsTable B. Tire Wear Troubleshooting Tire RepairLug nut Torque Requirements Lights and SignalsWheel Rims Wheels, Bearings and Lug nutsTroubleshooting generator Generator TroubleshootingSymptom Solution Troubleshooting engine Engine TroubleshootingPossible Cause Solution Symptom Possible Cause Solution Lamp Troubleshooting Troubleshooting lampsLamp starts slowly ARC does not strike Defective Lamp? When switch is first Checking voltage and ballast Turned onReplacement minimizes color differences Clean fixtureBallast Removal Lamp Troubleshooting GuideConnections StartingControl Panel Panel light/hour meter wiring diagramElectronic Components Locator To TB4-11 Wiring diagram Generator/LightsTB3 N Lights locator diagram Lights wiring diagram HERE’S HOW to GET Help