Multiquip LT6D operation manual Oil Filter Cartridge 200 Hours, Belt, Lamp Replacement

Page 39

maintenance

Oil Filter Cartridge (200 Hours)

1.Using a filter wrench, turn filter cartridge (Figure 27) to the left to remove it. If the filter cartridge is filled with a large amount of oil, wait 10 minutes or so before removing. Make sure there is no old gasket stuck on the filter holder.

OIL

FILTER

SEAL

Figure 27. Oil Filter

2.Tighten drain plug. Clean the filter holder, fill the new filter cartridge with clean engine oil, coat the packing and thread of the new filter cartridge with engine oil, then install it to the filter holder. Tighten until the gasket surface contacts the seal surface of the filter holder, then tighten it a further 3/4 to 1 turn.

3.Add engine oil through oil filler until the oil level is between the H and L marks on the dipstick.

4.Run the engine at idling for a short time, then stop the engine. Recheck the oil level and fill as necessary.

V-belt

Visually examine the V-belt (Figure 28) and determine if it is full of tiny cracks, frayed, has pieces of rubber missing, is peeling or otherwise damaged.

Also, examine the belt and determine if it is oil soaked or "glazed " (hard shiny appearance on the sides of the belt). Either of these two conditions can cause the belt to run hot, which can weaken it and increase the danger of it breaking.

If the V-belt exhibits any of the above wear conditions replace the V-belt immediately.

OIL SOAKED

GLAZED

CORD FAILURE

WORN BACK

COVER

BROKEN

MISSING RUBBER

CRACKS

SIDEWALL

WEAR

Figure 28. V-Belt Inspection

Lamp Replacement

NOTICE

If a light (lamp) replacement is required, allow light to cool for about 30 minutes before removing lamp. DO NOT touch light with your hands.

The oil and perspiration from one fingerprint may cause the lamp to fail prematurely. ALWAYS use a clean dry cloth for cleaning or handling lamps

1.Place all circuit breakers in the OFF position.

2.Remove protective lens and rubber gasket from lamp housing.

3.Remove defective lamp from housing.

4.Install new lamp, be careful not to touch lamp surface with your hands.

5.Reinstall protective lens and rubber gasket.

Flushing Out Radiator and Changing Coolant

WARNING

Allow engine to cool when flushing out radiator. Flushing the radiator while hot will damage radiator. In addition, the possibility of hot coolant exists which can cause severe burns.

LT6D LIGHT TOWER • operation manual — rev. #0 (07/16/13) — page 39

Image 39
Contents Model LT6D Proposition 65 warning Nhtsa Reporting Safety DefectsLT6D Light Tower Table of ContentsAddresses practices not related to personal injury Safety InformationSaFeTY messages SaFeTY sYmBOLsfirst aid kit GeneRaL saFeTY„ Always know the location of the nearest fire extinguisherLamp saFeTY Light Tower SafetyAny enclosed or narrow area EngIne saFeTY„ neveR tamper with the factory settings „ The engine of this equipmentFrom fuel vapors or if fuel is spilled on a hot engine FueL saFeTYTOWIng saFeTY „ neveR use fuel as a cleaning agentLoading and Tie-Down on Flatbed Truck TRanspORTIng saFeTY„ neveR use gas piping as an electrical ground ELeCTRICaL saFeTYPower Cord/Cable safety Grounding SafetyEnvIROnmenTaL saFeTY/DeCOmmIssIOnIng BaTTeRY saFeTYEmIssIOns InFORmaTIOn Emission Control LabelLabel must remain with the engine for its entire life Lamp Footcandle Plot Lamp footcandle plotLT6D Specifications Generator SpecificationsTrailer Specifications Engine Specifications Dimensions DimensionsReference Letter Description Dimension Metal Halide Lamps General informationPage Major Components 1 Control Panel Side ComponentsMajor Components 2 Control Panel Side Major Components Front/ Rear Page Control panel Control Panel/Ignition SwitchLED green lights when the engine is OK functioning normal Normal Operation Indicator This alarmKohler Engine Components Engine componentsEngine Oil Check InspectionEngine Servicing Light tower inspectionBattery Check Fuel CheckWipe up any spilled fuel immediately Operation in Freezing Weather Cleaning the RadiatorAir Cleaner Fan Belt Tension CoolantLight Power Cable Connections SetupIndoor Installation Lamp power cable connectionsLight tower grounding Outriggers and Support StandsLight tower from rolling Mast Operation Deploying the Mast Vertical Position Extending the MastRotating the Mast Operation Starting the EngineTurning On the Lights VAC Gfci Receptacle Testing the 120 VAC Gfci ReceptacleApplying an External Load 120/240 VAC Twist-Lock ReceptacleFrequency MaintenanceBasic Inspection and Maintenance Inspection/MaintenanceOFF position Air CleanerClean the inside of the cover using a damp cloth General InspectionFuel Addition Service DailyCleaning the Fuel Strainer Replacing Fuel FilterFlushing Out Radiator and Changing Coolant Lamp ReplacementOil Filter Cartridge 200 Hours BeltCheck Cable Wear Servicingthe Mast Raise/Lower Cable SystemReplace the pulley and the cable as needed Lower the mast to the horizontal resting position Servicingthe Mast Extension Cable SystemStorage Removal From Long Term StorageType Part Number Maintenance TrailersAdjustable Channel Trailer CouplersLeaf Suspension Wheel Hub AdjustmentTRaILeR TOWIng guIDeLInes COmmOn Causes for LOss of TRaILeRCOupLIng to THe TOW veHICLe DRIvIng COnDITIOnsInOpeRaBLe BRaKes, LIgHTs or mIRRORs TRaILeR TOWIng TIpsTRaILeR vIn Tag SIDe vIeW mIRRORs ELeCTRICaL COnneCTORTOW veHICLe SuspensIOn sYsTemBaLL COupLeR SaFeTY CHaInsJaCKsTanD COupLeR TYpesLock washer and hitch frame Before coupling trailer, inspect the hitch ball for wearAttaching safety Chain Connecting Trailer LightsUncoupling the Ball Hitch Pintle Coupler and pintle Hook PInTLe COupLeRCoupling Trailer to Tow vehicle pintle Coupler Unsafe Tires, Lug nuts or WheelsBe sure lug nuts are tight before each tow Determining Load Limit of TrailerStep Tighten lug nuts before each towDetermining Load Limit of Tow vehicle step TIRe FunDamenTaLsP indicates the tire is for passenger vehicles Uniform Tire Quality grading standards uTQgs Table a. Speed RatingLetter Rating Speed Rating Replacing Worn or Damaged Tires Tire Safety TipsTable B. Tire Wear Troubleshooting Tire RepairLug nut Torque Requirements Lights and SignalsWheel Rims Wheels, Bearings and Lug nutsTroubleshooting generator Generator TroubleshootingSymptom Solution Troubleshooting engine Engine TroubleshootingPossible Cause Solution Symptom Possible Cause Solution Lamp Troubleshooting Troubleshooting lampsLamp starts slowly ARC does not strike Defective Lamp? When switch is first Checking voltage and ballast Turned onReplacement minimizes color differences Clean fixtureBallast Removal Lamp Troubleshooting GuideConnections StartingControl Panel Panel light/hour meter wiring diagramElectronic Components Locator To TB4-11 Wiring diagram Generator/LightsTB3 N Lights locator diagram Lights wiring diagram HERE’S HOW to GET Help