Multiquip LT6D operation manual Fuel Check, Battery Check, Wipe up any spilled fuel immediately

Page 28

inspection

Fuel Check

CAUTION

Diesel fuel and its vapors are dangerous to your health and the surrounding environment. Avoid skin contact and/or inhaling fumes. DO NOT smoke while refueling. DO NOT attempt to refuel the

light tower if the engine is hot or running.

1.To check the engine fuel level, make sure the light tower is placed on secure level ground with the engine stopped.

2.Lift the light tower access door (Figure 9), control panel side. Set the door support latch in place to keep the door open (up).

Figure 9. Adding Fuel

3. Remove the fuel cap from the fuel tank.

CAUTION

ALWAYS fill the fuel tank with clean, fresh #2 diesel fuel. DO NOT fill the fuel tank beyond its capacity. DO NOT TOP-OFF.

4.Pay attention to the fuel tank capacity when replenishing fuel.The fuel tank cap must be closed tightly after filling. Handle fuel in a safe container. If the container does not have a spout, use a funnel.

5.Wipe up any spilled fuel immediately!

Battery Check

WARNING

The operator must wear the appropriate protective equipment and clothing while handling the battery.

Failure to wear protective equipment or clothing could result in serious injury.

The 12-volt DC battery (Figure 10) is shipped wet and is ready for use.

Figure 10. Battery (CA:550/CCA:430)

When servicing of the battery is required, perform the following:

„„A face shield and rubber gloves should be worn while handling and servicing the battery's electrolyte.

„„Disconnect battery terminal clamps, and remove the battery from the generator cabinet when servicing is required.

„„DO NOT overfill the battery.

WARNING

Electrolyte is an acid and must be handled with caution. ALWAYS follow servicing instructions from the electrolyte manufacturer to ensure safety. Serious

injury can result from careless handling and noncompliance to safety handling instructions.

Overfilling the battery may cause the electrolyte to overflow resulting in corrosion to nearby components. Immediately wash off any spilled electrolyte (battery acid).

page 28 — LT6D LIGHT TOWER • operation manual — rev. #0 (07/16/13)

Image 28
Contents Model LT6D Proposition 65 warning Reporting Safety Defects NhtsaTable of Contents LT6D Light TowerSafety Information SaFeTY messagesSaFeTY sYmBOLs Addresses practices not related to personal injuryGeneRaL saFeTY „ Always know the location of the nearestfire extinguisher first aid kitLight Tower Safety Lamp saFeTYEngIne saFeTY „ neveR tamper with the factory settings„ The engine of this equipment Any enclosed or narrow areaFueL saFeTY TOWIng saFeTY„ neveR use fuel as a cleaning agent From fuel vapors or if fuel is spilled on a hot engineTRanspORTIng saFeTY Loading and Tie-Down on Flatbed TruckELeCTRICaL saFeTY Power Cord/Cable safetyGrounding Safety „ neveR use gas piping as an electrical groundBaTTeRY saFeTY EnvIROnmenTaL saFeTY/DeCOmmIssIOnIngEmission Control Label EmIssIOns InFORmaTIOnLabel must remain with the engine for its entire life Lamp footcandle plot Lamp Footcandle PlotGenerator Specifications LT6D SpecificationsTrailer Specifications Engine Specifications Dimensions DimensionsReference Letter Description Dimension General information Metal Halide LampsPage Components Major Components 1 Control Panel SideMajor Components 2 Control Panel Side Major Components Front/ Rear Page Control Panel/Ignition Switch Control panelNormal Operation Indicator This alarm LED green lights when the engine is OK functioning normalEngine components Kohler Engine ComponentsInspection Engine ServicingLight tower inspection Engine Oil CheckFuel Check Battery CheckWipe up any spilled fuel immediately Cleaning the Radiator Air Cleaner Fan Belt TensionCoolant Operation in Freezing WeatherSetup Indoor InstallationLamp power cable connections Light Power Cable ConnectionsOutriggers and Support Stands Light tower groundingLight tower from rolling Mast Operation Extending the Mast Deploying the Mast Vertical PositionRotating the Mast Starting the Engine OperationTurning On the Lights Testing the 120 VAC Gfci Receptacle Applying an External Load120/240 VAC Twist-Lock Receptacle VAC Gfci ReceptacleMaintenance Basic Inspection and MaintenanceInspection/Maintenance FrequencyAir Cleaner Clean the inside of the cover using a damp clothGeneral Inspection OFF positionService Daily Cleaning the Fuel StrainerReplacing Fuel Filter Fuel AdditionLamp Replacement Oil Filter Cartridge 200 HoursBelt Flushing Out Radiator and Changing CoolantServicingthe Mast Raise/Lower Cable System Check Cable WearReplace the pulley and the cable as needed Servicingthe Mast Extension Cable System StorageRemoval From Long Term Storage Lower the mast to the horizontal resting positionMaintenance Trailers Adjustable ChannelTrailer Couplers Type Part NumberWheel Hub Adjustment Leaf SuspensionCOmmOn Causes for LOss of TRaILeR TRaILeR TOWIng guIDeLInesDRIvIng COnDITIOns COupLIng to THe TOW veHICLeTRaILeR TOWIng TIps InOpeRaBLe BRaKes, LIgHTs or mIRRORsTRaILeR vIn Tag ELeCTRICaL COnneCTOR TOW veHICLeSuspensIOn sYsTem SIDe vIeW mIRRORsSaFeTY CHaIns JaCKsTanDCOupLeR TYpes BaLL COupLeRBefore coupling trailer, inspect the hitch ball for wear Lock washer and hitch frameConnecting Trailer Lights Attaching safety ChainUncoupling the Ball Hitch PInTLe COupLeR Pintle Coupler and pintle HookUnsafe Tires, Lug nuts or Wheels Coupling Trailer to Tow vehicle pintle CouplerDetermining Load Limit of Trailer StepTighten lug nuts before each tow Be sure lug nuts are tight before each towTIRe FunDamenTaLs Determining Load Limit of Tow vehicle stepP indicates the tire is for passenger vehicles Table a. Speed Rating Uniform Tire Quality grading standards uTQgsLetter Rating Speed Rating Tire Safety Tips Table B. Tire Wear TroubleshootingTire Repair Replacing Worn or Damaged TiresLights and Signals Wheel RimsWheels, Bearings and Lug nuts Lug nut Torque RequirementsGenerator Troubleshooting Troubleshooting generatorSymptom Solution Engine Troubleshooting Troubleshooting enginePossible Cause Solution Symptom Possible Cause Solution Troubleshooting lamps Lamp TroubleshootingWhen switch is first Checking voltage and ballast Turned on Replacement minimizes color differencesClean fixture Lamp starts slowly ARC does not strike Defective Lamp?Lamp Troubleshooting Guide ConnectionsStarting Ballast RemovalPanel light/hour meter wiring diagram Control PanelElectronic Components Locator Wiring diagram Generator/Lights To TB4-11TB3 N Lights locator diagram Lights wiring diagram HERE’S HOW to GET Help