Multiquip SG1400C3 operation manual InteliVision 5 Digital Controller

Page 18

general information

InteliVision 5 ™ Digital Controller

The InteliVision 5 Digital Controller provides monitoring and fault detection capability of all engine and generator operating parameters. A list of operating parameters is shown below:

AC Metering Display

•Voltage/Amperage / Frequency

•Generator Phase Voltage / Current

•Generator Frequency

Engine Information Display

•Engine Temperature / Oil Pressure (psi)

•Battery Voltage (DC) / Tachometer

•Hourmeter

Minor Fault Warning Display

•Switch Not In Auto

•Low Fuel Level

•Low Oil Pressure Alarm

•Low Engine Temperature

•High Engine Temperature Alarm

•Low Battery Voltage

•High Battery Voltage

•Weak Battery Condition

•Battery Charger Input Fail

•Undervoltage

•Over / Underfrequency

•Overcurrent

Major Fault Shutdown Display

•Overvoltage

•Emergency Stop

•Loss Of Speed

•Overcrank

•Overspeed

•Low Oil Pressure

•High Engine Temperature

•Low Coolant Level

•Spare Programmable Digital Faults

Switches And Operating Controls

•Run / Off / Auto / Load Test Buttons

•Decrement / Increment / Previous (Exit) /Next (Enter) Program Buttons

•Emergency Stop Button

•Audible Alarm Horn

•Alarm Horn Silence Button

•Lamp Test Button

•Fault Reset Function

•RS-485 Remote Communications, External Expansion Module Ports

Timer Countdown Display

•Engine Start Delay

•Oil Bypass

•Overcrank

•Cycle Crank

•Starter Re-engage Delay

•Bypass Delay

Control LED Indicators

•Switch Position (Run, Off, Auto, Test)

•Common Alarm (Minor Fault)

•Common Shutdown (Major Fault)

•Generator Ready (When in Auto)

•Speed Signal

•Emergency Stop

Diagnostic LED Indicators:

•Run Output Energized

•Crank Output Energized

•Remote Start Signal Initiated

•Common Fail Output Energized

•Watchdog - CPU Running

•Programmable Output Contacts

page 18 — SG1400C3 Studio Generator • operation manual — rev. #0 (10/05/11)

Image 18

Contents Model SG1400C3 Proposition 65 warning Reporting Safety Defects NhtsaTable of Contents Choose from three easy options Safety Information SaFeTY meSSageSSaFeTY SYmBolS General SaFeTY GeneraTor SaFeTYEngine SaFeTY Restricted. If the air fl ow isIf operating in speed ranges above the maximum allowable „ never use fuel as a cleaning agent Fuel SaFeTYToWing SaFeTY From fuel vapors or if fuel is spilled on a hot engineGrounding Safety EleCTriCal SaFeTYPower Cord/Cable Safety DeathBaTTerY SaFeTY EnvironmenTal SaFeTYSpecifications Model Cummins QSB7-G5Dimensions DimensionsInstallation Typical Generator Grounding ApplicationOutdoor Installation Indoor InstallationGenerator Grounding General information Fuel Water Separator Fuel TankFuel Priming Pump Intake Ventilation DoorInteliVision 5 Digital Controller Page Generator Major Components Major ComponentsDescription Oil Filter Oil Filler CapAlternator StarterBasic Trailer Components License Plate Lights Illuminates license plateController Power Switch Provides power to engine controller Control panelCamlok/voltage output panel Camlok/Voltage Output PanelCircuit Breaker panel Main Breaker PanelDigital controller MCB Control Button Not functional in this applicationLoad application/generator output Single Phase LoadThree Phase Load Type of LoadVoltage Selector Switch Generator Output VoltagesGenerator Amperage Lubrication Oil Inspection/setupRefueling Procedure Fuel CheckOnly use #2 diesel fuel when refueling Remove fuel cap and fill tank FigureWait for fuel to rise in filler neck Coolant Antifreeze/summer coolant Cleaning the RadiatorAir Cleaner Fan Belt Tension Drive Belt inspection Operation in Freezing WeatherWhen connecting the battery do the following Battery Cable InstallationWiring AlternatorAlways have adequate ventilation when operating Before StartingEngine’s exhaust contains harmful emissions Engine will go to idle mode StartupStarting Manual Normal Shutdown Procedure Emergency Shutdown ProcedureClosing the Enclosure DOORs Protective devices Protective devicesMaintenance Engine Maintenance ScheduleGeneral Inspection Air Filter Dust IndicatorCleaning Inside the Fuel Tank Air FilterAir Removal Fuel Tank InspectionReplacing Fuel Filter Check Oil LevelHydraulic Brakes Manually Adjusting the BrakesTrailer Brakes Hydraulic Brake ActuatorAdjustable Channel Wheel BearingsWheel Hub Adjustment Leaf SuspensionTroubleshooting generator Troubleshooting GeneratorTroubleshooting engine Troubleshooting EngineTroubleshooting controller Troubleshooting Intelivision 5 ControllerTrailer guidelines Common CauSeS For loSS oF TrailerTrailer ToWing guidelineS Driving CondiTionS Coupling To THe ToW veHiCleInoperaBle BraKeS, ligHTS or mirrorS Trailer ToWing TipSTrailer vin Tag SuSpenSion SYSTem EleCTriCal ConneCTorToW veHiCle BraKe ConTrollerEmergenCY FlareS andTriangle reFleCTorS SaFeTY CHainSTrailer ligHTing and BraKing ConneCTor BreaKaWaY SYSTemLock washer and hitch frame Trailer tongue. Wood or concrete blocks may also be usedCoupling the Trailer to the Tow vehicle Ball Coupler Attaching Safety Chain Breakaway Brake SystemBreakaway Cable Surge Brake System PinTle HiTCH Coupler Connecting Trailer lightsUncoupling the Ball Hitch Pintle Coupler and pintle HookFigure H. Attaching Safety Chain Pintle Hitch Coupling Trailer to Tow vehicle pintle CouplerTire SaFeTY Unsafe Tires, lug nuts or Wheels Determining load limit of TrailerBe sure lug nuts are tight before each tow Step Determining load limit of Tow vehicle StepTire FundamenTalS Letter rating Speed ratingReplacing Worn or damaged Tires Tire Safety TipsTire repair Uniform Tire Quality grading Standards uTQgSWheel rims Wheels, Bearings and lug nutsLug nut Torque requirements Lights and Signals Figure M. Trailer to Tow Vehicle Wiring DiagramHERE’S HOW to GET Help