Multiquip SG1400C3 operation manual Outdoor Installation, Indoor Installation, Generator Grounding

Page 15

installation

Outdoor Installation

Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around. Also install the generator in a manner so that the exhaust will not be discharged in the direction of nearby homes.

The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to engine and alternator parts.

CAUTION

Pay close attention to ventilation when operating the generator inside tunnels and caves.The engine exhaust contains noxious elements. Engine exhaust must be routed to a ventilated area.

Indoor Installation

Exhaust gases from diesel engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.

Generator Grounding

To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground.

Article 250 (Grounding) of the National Electrical Code (NEC) provides guidelines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following grounding requirements:

1.Use one of the following wire types to connect the generator to earth ground.

a.Copper - 10 AWG (5.3 mm2)

b.Aluminum - 8 AWG (8.4 mm2)

2.When grounding the generator (Figure 2) connect the ground cable between the lock washer and the nut on the generator and tighten the nut fully. Connect the other end of the ground cable to earth ground.

3.NEC article 250-52(c) specifies that the earth ground rod should be buried a minimum of 8 ft. into the ground.

NOTICE

When connecting the generator to any buildings electrical system ALWAYS consult with a licensed electrician.

NOTICE

If connection of the ground rod is not feasible, please check city, local or state electrical requirements on generator grounding requirements.

SG1400c3 studio generator • operation manual — rev. #0 (10/05/11) — page 15

Image 15
Contents Model SG1400C3 Proposition 65 warning Nhtsa Reporting Safety DefectsTable of Contents Choose from three easy options Safety Information SaFeTY meSSageSSaFeTY SYmBolS GeneraTor SaFeTY General SaFeTYEngine SaFeTY Restricted. If the air fl ow isIf operating in speed ranges above the maximum allowable From fuel vapors or if fuel is spilled on a hot engine Fuel SaFeTYToWing SaFeTY „ never use fuel as a cleaning agentDeath EleCTriCal SaFeTYPower Cord/Cable Safety Grounding SafetyEnvironmenTal SaFeTY BaTTerY SaFeTYModel Cummins QSB7-G5 SpecificationsDimensions DimensionsTypical Generator Grounding Application InstallationOutdoor Installation Indoor InstallationGenerator Grounding General information Intake Ventilation Door Fuel TankFuel Priming Pump Fuel Water SeparatorInteliVision 5 Digital Controller Page Major Components Generator Major ComponentsDescription Starter Oil Filler CapAlternator Oil FilterLicense Plate Lights Illuminates license plate Basic Trailer ComponentsControl panel Controller Power Switch Provides power to engine controllerCamlok/Voltage Output Panel Camlok/voltage output panelMain Breaker Panel Circuit Breaker panelMCB Control Button Not functional in this application Digital controllerType of Load Single Phase LoadThree Phase Load Load application/generator outputVoltage Selector Switch Generator Output VoltagesGenerator Amperage Fuel Check Inspection/setupRefueling Procedure Lubrication OilOnly use #2 diesel fuel when refueling Remove fuel cap and fill tank FigureWait for fuel to rise in filler neck Operation in Freezing Weather Cleaning the RadiatorAir Cleaner Fan Belt Tension Drive Belt inspection Coolant Antifreeze/summer coolantAlternator Battery Cable InstallationWiring When connecting the battery do the followingAlways have adequate ventilation when operating Before StartingEngine’s exhaust contains harmful emissions Engine will go to idle mode StartupStarting Manual Normal Shutdown Procedure Emergency Shutdown ProcedureClosing the Enclosure DOORs Protective devices Protective devicesEngine Maintenance Schedule MaintenanceAir Filter Air Filter Dust IndicatorCleaning Inside the Fuel Tank General InspectionCheck Oil Level Fuel Tank InspectionReplacing Fuel Filter Air RemovalHydraulic Brake Actuator Manually Adjusting the BrakesTrailer Brakes Hydraulic BrakesWheel Bearings Adjustable ChannelLeaf Suspension Wheel Hub AdjustmentTroubleshooting Generator Troubleshooting generatorTroubleshooting Engine Troubleshooting engineTroubleshooting Intelivision 5 Controller Troubleshooting controllerTrailer guidelines Common CauSeS For loSS oF TrailerTrailer ToWing guidelineS Coupling To THe ToW veHiCle Driving CondiTionSInoperaBle BraKeS, ligHTS or mirrorS Trailer ToWing TipSTrailer vin Tag BraKe ConTroller EleCTriCal ConneCTorToW veHiCle SuSpenSion SYSTemBreaKaWaY SYSTem SaFeTY CHainSTrailer ligHTing and BraKing ConneCTor EmergenCY FlareS andTriangle reFleCTorSLock washer and hitch frame Trailer tongue. Wood or concrete blocks may also be usedCoupling the Trailer to the Tow vehicle Ball Coupler Attaching Safety Chain Breakaway Brake SystemBreakaway Cable Surge Brake System Pintle Coupler and pintle Hook Connecting Trailer lightsUncoupling the Ball Hitch PinTle HiTCH CouplerCoupling Trailer to Tow vehicle pintle Coupler Figure H. Attaching Safety Chain Pintle HitchTire SaFeTY Unsafe Tires, lug nuts or Wheels Determining load limit of TrailerBe sure lug nuts are tight before each tow Determining load limit of Tow vehicle Step StepLetter rating Speed rating Tire FundamenTalSUniform Tire Quality grading Standards uTQgS Tire Safety TipsTire repair Replacing Worn or damaged TiresWheel rims Wheels, Bearings and lug nutsLug nut Torque requirements Figure M. Trailer to Tow Vehicle Wiring Diagram Lights and SignalsHERE’S HOW to GET Help