Land Pride Z52, Z60 Driving the Mower, Operating Suggestions, Steering, To Stop or Decrease Speed

Page 19

Land Pride

Section 2 Operation

Driving the Mower

!DANGER!

Never make sudden stops or reverse direction, especially when going down a slope. The steering is designed for sensitive response. Rapid movement of the control levers in either direction could result in a reaction of the mower that can cause serious injury.

Steering

Refer to Figure 2-9:

After starting engine, engage the control levers and steer as follows:

To Go Forward:

Push control levers forward an equal distance.

To Go in Reverse:

Pull control levers rearward an equal distance.

To Turn Left:

Move the right control lever farther forward from neutral than the left control lever.

To Turn Right:

Move the left control lever farther forward from neutral than the right control lever.

To Pivot Turn:

Move one control lever forward and the other control lever back of neutral, this will allow the drive wheels to counter- rotate.

To Stop or Decrease Speed

!WARNING!

In the event of a system failure while mowing, engage both parking brakes to stop or slow mower. Refer to Figure 2-4.

Move control levers to neutral. When going forward pull back gently on control levers. When going in reverse push forward gently on control levers.

!DANGER!

When going in reverse push forward gently on control levers and avoid sudden movement. Any sudden movement could cause the front of the mower to come off of the ground resulting in possible loss of control.

To Increase Speed

Increase control levers equal distance from neutral. The farther forward control levers are from neutral, the faster mower will travel forward. The farther back control levers are from neutral, the faster mower will go in reverse.

Operating Suggestions

!DANGER!

Prior to operating the mower the operator should be thoroughly familiar with the proper use and operation of the equipment, should read the manual completely and thoroughly, and should have attempted slow moving maneuvers to become familiar with the operation of the equipment before attempting normal speed operation. An inexperienced operator should not mow on slopes or on uneven terrain.

!WARNING!

The mower’s control levers are very responsive: Easy does it! For smooth operation, move lever slowly, avoid sudden movement. Skill and ease of operation come with practice and experience.

Inexperienced operators may have a tendency to over-steer and lose control. Slow-moving practice maneuvers are recommended to become familiar with these characteristics before attempting normal speed operation.

!WARNING!

Sharp depressions or raised obstacles (such as gutters or curbs) should not be directly approached at high speed in an attempt to jump them as the operator could be thrown from the equipment. Approach at a slow speed and angle one drive wheel at the obstruction. Continue at an angle until the wheel clears and then pivot the opposite wheel around.

When turning on soft wet turf, keep both wheels rolling either forward or backward. Pivoting on one stopped wheel can damage turf. This is especially important when mowing.

Peak mowing performance is maintained when the throttle is set at full rpm. This gives maximum power to the drive wheels and deck when needed. Use the control levers to control ground speed rather than engine rpm.

!WARNING!

Do not operate the equipment while wearing sandals, tennis shoes, sneakers, shorts or any type of loose fitting clothing. Always wear long pants, safety glasses and safety shoes when operating this machine.

Keep blades sharp. Many professional mowing companies have additional sets of blades and change blades twice a day: once in the morning and again at noon. Many problems with incorrect cutting patterns are due to dull blades or blades which have been sharpened incorrectly. Information on sharpening blades is listed in this manual’s maintenance section. In addition, most communities have individuals or companies which specialize in sharpening mower blades. Blade sharpness should be checked daily.

03/11/03

Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M

17

Image 19
Contents Accu-Z Table of Contents Shutdown and Storage Be Aware of Signal WordsKeep Riders Off Machinery For Your ProtectionSafety at All Times Practice Safe MaintenanceWear Protective Equipment Prepare for EmergenciesAvoid High Pressure Fluids Hazard 838-303C Important Safety Information838-399C 838-307C 838-308C 838-310CIntroduction Using This ManualApplication Owner AssistanceRemote Air Cleaner Assembly Control Lever and Seat AssemblyAssembly and Set-Up Optional Equipment Assemblies Remote Air Cleaner AssemblyControl Lever Extensions Mower Deck Preparation Accu-Vac AssemblyBlower Drive Belt Blower, Pulley and Pulley Cover AssemblyBagger Assembly Bagger Assembly Throttle Control Ignition SwitchControls OperationControl Levers Blade Engagement SwitchControl Levers Deck Height Deck Lift Locking PinHour Meter Safety Start Interlock SystemInstrumentation Engine StartingFront of mower Faces This Direction Moving Mower with Stalled EngineTo Stop or Decrease Speed Driving the MowerOperating Suggestions SteeringMower Deck Operation Operating Instructions Control Lever Park Brake Slot AdjustmentsTorque Values Steering LinkageJam Nut Control Lever Neutral AdjustmentStop Control Lever Nylock Nut Linkage Reverse Spring AdjustmentControl Lever Stops Top Nylock Nut Reverse SpringSteering Dampener Upper Control Lever Cap Screw Lower Park Brake AdjustmentControl Lever Adjustment Steering DampenerBrake Linkage Turnbuckle Front Brake Link Right SideControl Lever Park Brake Slot Outside Edge Travel Slot By-Pass Valve Jam NutDeck Leveling and Height Adjustment Hydraulic Pump Belt AdjustmentDeck Drive Belt Adjustment Engine RPM SettingDeck Level Adjustments Stop Handle Height Adjusting BlocksDeck Lift Threaded Rod Nut Nut Chain Deck Lift Threaded Rod Foot Pedal Nut Nut Chain Bolt Adjuster Jam Nut HardwareLift Block Deck Lift Rod Assist Springs Height Adjusting Stop Plate Deck Cutting Height AdjustmentAnti-Scalp Rollers Anti-Scalp Rollers Adjusting HolesTop View Deck Top View Bottom View Maintenance and LubricationMaintenance Schedule Torque Values MaintenanceRefer to Tire Inflation Chart TiresHour Meter BatteryLubrication Electrical System Hydraulic Reservoir Hydraulic Filter Access to Engine and Hydraulic PumpsHydraulic System Seat Platform Seat Platform Catch Control LeverEngine Oil and Filter Fuel SystemFuel Filter Over Servicing Improper InstallationEngine Air Filter Engine Oil Filler Tube Oil Filter Drain PlugIncorrect Air Filter Element Engine Air Filter Service ProcedureGeneral Engine Maintenance Damaged Filter, Seals or CanisterLift Jack Option Belt ReplacementMower Blade Maintenance Mower Blade RemovalNew Season Preparation Preparation of Engine for StorageSpecifications and Capacities Parking Safety FeaturesIndicators Weight Kit52, 60 or 72 Cutting width Features and BenefitsTroubleshooting Inflation PSI Tire Inflation ChartAppendix TireWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 6 pages 11.76 Kb

Z60, Z52, Z52 , Z60, Z72 specifications

Land Pride is a recognized leader in the manufacturing of high-quality outdoor equipment, particularly known for their commercial mowers. Among their lineup, models like the ZXT54, ZT60, Z52, Z44, and ZT72 stand out for their commitment to performance, durability, and ease of use. These zero-turn mowers are designed to tackle a variety of mowing tasks, making them ideal for both residential and commercial applications.

The Land Pride ZXT54 model features a 54-inch cutting deck, which provides ample width for efficient mowing. Its powerful engine, designed for reliability and performance, ensures that grass can be cut cleanly and quickly, even in challenging conditions. Users appreciate the intuitive controls that allow for precise maneuvering, making it easy to navigate around obstacles like trees and flower beds. The ZXT54 also includes features such as a comfortable seat and ergonomic handle grips, enhancing operator comfort during extended use.

Moving to the ZT60, this model takes it a step further with a 60-inch cutting deck. This increased size makes it ideal for large lawns or commercial properties, allowing more area to be covered in less time. The ZT60 is equipped with advanced mowing technology that ensures an even cut and a clean finish. An adjustable cutting height gives users the flexibility to adapt to different grass types and growth conditions.

The Z52 model is another solid option for users looking for a balance between power and maneuverability. With a 52-inch cutting deck, this model is favored for its agility in tighter spaces while still providing a robust mowing performance. The Z52 boasts some of the latest technological advancements, including a heavy-duty chassis and an efficient engine that prolongs work time and reduces wear.

For smaller properties, the Z44 model shines with its 44-inch deck, making it perfect for navigating narrow spaces without compromising on cutting performance. Its compact size does not sacrifice power, as it is outfitted with a capable engine that can handle various grass types while providing a reliable performance.

Finally, the ZT72 model, with its impressive 72-inch cutting deck, is engineered specifically for extensive commercial use. It is built to withstand demanding conditions, featuring heavy-duty components that ensure longevity. The ZT72 also includes advanced features like an enhanced mulching option and a robust suspension system, providing a smooth ride over uneven terrain.

In summary, the Land Pride ZXT54, ZT60, Z52, Z44, and ZT72 models each offer unique features tailored to meet the varying needs of users. Whether for residential use or commercial applications, these mowers deliver power, efficiency, and unmatched comfort, ensuring that mowing tasks are completed effectively and with ease.