Land Pride Z52 , Z60, Z72 manual Engine Air Filter Service Procedure, General Engine Maintenance

Page 39

Land Pride

Section 4 Maintenance and Lubrication

Damaged Filter, Seals or Canister

Never bang or bump the filter element against the tire or any solid object, as dust and dirt particles will be forced through the media causing continual passing of dirt into the engine. Visually inspect the outside of the air cleaner canister periodically for external damage and replace if necessary.

Incorrect Air Filter Element

Use only the correct Donaldson air filter element, Land Pride part number 839-312C, which is designed to fit the canister properly. Land Pride air filter elements have the correct media composition, filter area, micron size and dimensions. Always use genuine Land Pride filters. Many aftermarket filters have been found to be incompatible with Land Pride’s canisters and engines.

The air filter must remain intact to block passage of dirt and foreign particles from entering the engine. Being inclined to disbelieve the need for more expensive air filter elements used on gasoline engines may cause some individuals to opt for a less expensive part.

The filter element must be sufficient size and construction to withstand stresses, caused by rapid cycling of the air volume demanded by the engine, without cracking or tearing under fatigue and pressure (especially diesel engines). Therefore, Land Pride and the engine manufacturers have carefully selected a reliable filter designed to fit the needs of the engines. The filter specified is a Donaldson filter, Land Pride part number 839-312C.

Owners should be reminded that failure to use original equipment replacement parts is an alteration and will not be considered for warranty in the event of engine damage.

Engine Air Filter Service Procedure

1.Release clamps and remove element. Clean the canister with a damp cloth.

2.Before installing a new element, inspect it by placing a bright light inside and rotate the element slowly, looking for any holes or tears in the paper. Also check gaskets for cuts or tears. Do not attempt to use a damaged element which will allow abrasive particles to enter the engine.

3.Reinstall the dust cup. Make sure it seals all the way around the air cleaner body, then tighten the clamps.

4.Check all fittings and clamps periodically for tightness and inspect hoses for holes or cracks.

5.Periodically check the intake hose for signs of ingested dust. Locate and repair the source of ingested dirt.

6.Never operate a machine without an air filter installed.

General Engine Maintenance

Detailed instructions and recommendations for break-in and regular maintenance are specified in the Engine Operator’s manual. Please refer to this manual for engine servicing, lubricating oil levels with quality and viscosity recommendations, bolt torques, etc. The engine warranty is backed by the engine manufacturer. Special attention should be paid to applicable data which will not be duplicated here.

2

5

2

3

1

19067

2

5

6

4

1.Spindle drive belt

2.Deck blade spindle pulley

3.Spindle belt tension idler

4.Spindle belt tension idler spring (9.0" at operation)

5.Deck belt idler

6.Idler arm

1.

Pump belt

 

2.

Engine pulley

 

3.

Pump idler pulley

 

4.

Pump idler arm

 

5.

Pump pulley

 

6.

Electric deck clutch

 

7.

Pump idler spring

 

 

 

1

 

 

5

 

 

4

 

5

 

 

2,6

7

19068

3

 

Deck Belt Drive Layout

Mower Viewed from Bottom Deck

Figure 4-10

Figure 4-11

03/11/03

Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M

37

Image 39
Contents Accu-Z Table of Contents Shutdown and Storage Be Aware of Signal WordsKeep Riders Off Machinery For Your ProtectionSafety at All Times Practice Safe MaintenancePrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard 838-303C Important Safety Information838-399C 838-307C 838-308C 838-310CIntroduction Using This ManualApplication Owner AssistanceControl Lever and Seat Assembly Remote Air Cleaner AssemblyAssembly and Set-Up Remote Air Cleaner Assembly Optional Equipment AssembliesControl Lever Extensions Mower Deck Preparation Accu-Vac AssemblyBlower Drive Belt Blower, Pulley and Pulley Cover AssemblyBagger Assembly Bagger Assembly Throttle Control Ignition SwitchControls OperationControl Levers Blade Engagement SwitchControl Levers Deck Height Deck Lift Locking PinHour Meter Safety Start Interlock SystemInstrumentation Engine StartingFront of mower Faces This Direction Moving Mower with Stalled EngineTo Stop or Decrease Speed Driving the MowerOperating Suggestions SteeringMower Deck Operation Operating Instructions Control Lever Park Brake Slot AdjustmentsTorque Values Steering LinkageControl Lever Neutral Adjustment Jam NutStop Control Lever Nylock Nut Linkage Reverse Spring AdjustmentControl Lever Stops Top Nylock Nut Reverse SpringSteering Dampener Upper Control Lever Cap Screw Lower Park Brake AdjustmentControl Lever Adjustment Steering DampenerBrake Linkage Turnbuckle Front Brake Link Right SideControl Lever Park Brake Slot Outside Edge Travel Slot By-Pass Valve Jam NutDeck Leveling and Height Adjustment Hydraulic Pump Belt AdjustmentDeck Drive Belt Adjustment Engine RPM SettingStop Handle Height Adjusting Blocks Deck Level AdjustmentsDeck Lift Threaded Rod Nut Nut Chain Bolt Adjuster Jam Nut Hardware Deck Lift Threaded Rod Foot Pedal Nut Nut ChainLift Block Deck Lift Rod Assist Springs Height Adjusting Stop Plate Deck Cutting Height AdjustmentAnti-Scalp Rollers Anti-Scalp Rollers Adjusting HolesTop View Deck Top View Bottom View Maintenance and LubricationMaintenance Schedule Torque Values MaintenanceRefer to Tire Inflation Chart TiresBattery Hour MeterLubrication Electrical System Hydraulic Reservoir Hydraulic Filter Access to Engine and Hydraulic PumpsHydraulic System Seat Platform Seat Platform Catch Control LeverFuel System Engine Oil and FilterFuel Filter Over Servicing Improper InstallationEngine Air Filter Engine Oil Filler Tube Oil Filter Drain PlugIncorrect Air Filter Element Engine Air Filter Service ProcedureGeneral Engine Maintenance Damaged Filter, Seals or CanisterLift Jack Option Belt ReplacementMower Blade Maintenance Mower Blade RemovalNew Season Preparation Preparation of Engine for StorageSpecifications and Capacities Parking Safety FeaturesIndicators Weight Kit52, 60 or 72 Cutting width Features and BenefitsTroubleshooting Inflation PSI Tire Inflation ChartAppendix TireWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 6 pages 11.76 Kb

Z60, Z52, Z52 , Z60, Z72 specifications

Land Pride is a recognized leader in the manufacturing of high-quality outdoor equipment, particularly known for their commercial mowers. Among their lineup, models like the ZXT54, ZT60, Z52, Z44, and ZT72 stand out for their commitment to performance, durability, and ease of use. These zero-turn mowers are designed to tackle a variety of mowing tasks, making them ideal for both residential and commercial applications.

The Land Pride ZXT54 model features a 54-inch cutting deck, which provides ample width for efficient mowing. Its powerful engine, designed for reliability and performance, ensures that grass can be cut cleanly and quickly, even in challenging conditions. Users appreciate the intuitive controls that allow for precise maneuvering, making it easy to navigate around obstacles like trees and flower beds. The ZXT54 also includes features such as a comfortable seat and ergonomic handle grips, enhancing operator comfort during extended use.

Moving to the ZT60, this model takes it a step further with a 60-inch cutting deck. This increased size makes it ideal for large lawns or commercial properties, allowing more area to be covered in less time. The ZT60 is equipped with advanced mowing technology that ensures an even cut and a clean finish. An adjustable cutting height gives users the flexibility to adapt to different grass types and growth conditions.

The Z52 model is another solid option for users looking for a balance between power and maneuverability. With a 52-inch cutting deck, this model is favored for its agility in tighter spaces while still providing a robust mowing performance. The Z52 boasts some of the latest technological advancements, including a heavy-duty chassis and an efficient engine that prolongs work time and reduces wear.

For smaller properties, the Z44 model shines with its 44-inch deck, making it perfect for navigating narrow spaces without compromising on cutting performance. Its compact size does not sacrifice power, as it is outfitted with a capable engine that can handle various grass types while providing a reliable performance.

Finally, the ZT72 model, with its impressive 72-inch cutting deck, is engineered specifically for extensive commercial use. It is built to withstand demanding conditions, featuring heavy-duty components that ensure longevity. The ZT72 also includes advanced features like an enhanced mulching option and a robust suspension system, providing a smooth ride over uneven terrain.

In summary, the Land Pride ZXT54, ZT60, Z52, Z44, and ZT72 models each offer unique features tailored to meet the varying needs of users. Whether for residential use or commercial applications, these mowers deliver power, efficiency, and unmatched comfort, ensuring that mowing tasks are completed effectively and with ease.