Land Pride Z60, Z52 Instrumentation, Safety Start Interlock System, Engine Starting, Hour Meter

Page 17

Land Pride

Section 2 Operation

Instrumentation

Electronic Hour Meter

Refer to Figure 2-7:

Registers 1/10 hour increments up to 9,999.9 total hours. Connected to the ignition switch, the meter records the accumulative time while the ignition key is switched to the RUN position and the operator is on the seat.

19062

Hour Meter

Hour Meter

Figure 2-7

Oil Pressure Light

5.With the deck clutch switch up and/or the control levers in the neutral position, slowly raise off of the seat. The engine should stop within two seconds.

6.If the engine fails to stop when the deck clutch switch is up or one or both of the control levers is in and the operator is off the seat, check the function of the seat switch. If the seat switch is not operating properly and if the cause can not be determined, replace the seat switch.

If the problem can not be located, contact your Land Pride Dealer.

!WARNING!

The safety interlock system should always function per steps 4 and 5. If it does not function properly, it should be corrected immediately. Do not operate the mower without a properly functioning seat safety switch.

!WARNING!

The safety interlock system must not be disconnected or bypassed.

NOTE: The operator’s seat is equipped with a separate safety switch. If for any reason the operator should become unseated when the neutral switches are disengaged or the deck clutch switch is engaged the engine will stop.

Refer to Figure 2-2:

This light comes on when the ignition switch is placed in the RUN position and stays lit until the engine is running and a safe oil pressure is developed. If light comes on during operation, shut engine off immediately and locate and correct the problem.

Safety Start Interlock System

The mower is equipped with a safety start interlock system consisting of the brake switches, seat switch, and deck clutch switch. Check mower safety start interlock system daily, prior to operation. This system is an important mower safety feature. It should be repaired immediately if it malfunctions. The machine incorporates a separate seat switch which will stop the mower engine when the operator is unseated for any reason while the mower is moving or the deck clutch is engaged. This is a safety feature designed to prevent runaway or accidental entanglement. To inspect the system:

1.The operator must be on the seat when testing the seat switch.

2.Set both control levers in the park brake position.

3.Start the engine and allow it to warm up to operating temperature.

4.With the deck clutch switch down and the control levers in the park brake position, slowly raise off of the seat. The engine should continue to run.

Engine Starting

The Accu Z safety start interlock system is also designed to protect the operator and others from accidental injury due to unintentional engine starting. The engine starting motor will not engage until:

A. Control levers are in the brake position.

B. Deck clutch switch is in the down (OFF) position.

The following steps are the correct procedures for starting the engine. If difficulty is encountered, contact the Land Pride Dealer in your area.

1.Before starting mower each day, perform daily pre- operation checking.

2.Make sure the control levers are in the brake position and deck clutch switch is disengaged.

3.Set throttle at approximately 1/2 open position.

NOTE: Use choke position when engine is cold, or if warm engine fails to start within 5 seconds of cranking. Avoid flooding and operate engine without choking as soon as possible.

4.Insert key in ignition switch and rotate full clockwise to engage starting motor. Release key when engine starts.

03/11/03

Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M

15

Image 17
Contents Accu-Z Table of Contents Keep Riders Off Machinery Be Aware of Signal WordsFor Your Protection Shutdown and StorageSafety at All Times Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment 838-303C Important Safety Information838-399C 838-307C 838-308C 838-310CApplication Using This ManualOwner Assistance IntroductionAssembly and Set-Up Control Lever and Seat AssemblyRemote Air Cleaner Assembly Control Lever Extensions Remote Air Cleaner AssemblyOptional Equipment Assemblies Mower Deck Preparation Accu-Vac AssemblyBlower Drive Belt Blower, Pulley and Pulley Cover AssemblyBagger Assembly Bagger Assembly Controls Ignition SwitchOperation Throttle ControlControl Levers Blade Engagement SwitchDeck Height Deck Lift Locking Pin Control LeversInstrumentation Safety Start Interlock SystemEngine Starting Hour MeterFront of mower Faces This Direction Moving Mower with Stalled EngineOperating Suggestions Driving the MowerSteering To Stop or Decrease SpeedMower Deck Operation Operating Instructions Torque Values AdjustmentsSteering Linkage Control Lever Park Brake SlotStop Control Lever Control Lever Neutral AdjustmentJam Nut Control Lever Stops Reverse Spring AdjustmentTop Nylock Nut Reverse Spring Nylock Nut LinkageControl Lever Adjustment Park Brake AdjustmentSteering Dampener Steering Dampener Upper Control Lever Cap Screw LowerControl Lever Park Brake Slot Outside Edge Travel Slot Front Brake Link Right SideBy-Pass Valve Jam Nut Brake Linkage TurnbuckleDeck Drive Belt Adjustment Hydraulic Pump Belt AdjustmentEngine RPM Setting Deck Leveling and Height AdjustmentDeck Lift Threaded Rod Nut Nut Chain Stop Handle Height Adjusting BlocksDeck Level Adjustments Lift Block Deck Lift Rod Assist Springs Bolt Adjuster Jam Nut HardwareDeck Lift Threaded Rod Foot Pedal Nut Nut Chain Height Adjusting Stop Plate Deck Cutting Height AdjustmentAnti-Scalp Rollers Anti-Scalp Rollers Adjusting HolesTop View Deck Top View Bottom View Maintenance and LubricationMaintenance Schedule Refer to Tire Inflation Chart MaintenanceTires Torque ValuesLubrication Electrical System BatteryHour Meter Hydraulic System Access to Engine and Hydraulic PumpsSeat Platform Seat Platform Catch Control Lever Hydraulic Reservoir Hydraulic FilterFuel Filter Fuel SystemEngine Oil and Filter Engine Air Filter Improper InstallationEngine Oil Filler Tube Oil Filter Drain Plug Over ServicingGeneral Engine Maintenance Engine Air Filter Service ProcedureDamaged Filter, Seals or Canister Incorrect Air Filter ElementMower Blade Maintenance Belt ReplacementMower Blade Removal Lift Jack OptionNew Season Preparation Preparation of Engine for StorageSpecifications and Capacities Indicators Safety FeaturesWeight Kit Parking52, 60 or 72 Cutting width Features and BenefitsTroubleshooting Appendix Tire Inflation ChartTire Inflation PSIWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 6 pages 11.76 Kb

Z60, Z52, Z52 , Z60, Z72 specifications

Land Pride is a recognized leader in the manufacturing of high-quality outdoor equipment, particularly known for their commercial mowers. Among their lineup, models like the ZXT54, ZT60, Z52, Z44, and ZT72 stand out for their commitment to performance, durability, and ease of use. These zero-turn mowers are designed to tackle a variety of mowing tasks, making them ideal for both residential and commercial applications.

The Land Pride ZXT54 model features a 54-inch cutting deck, which provides ample width for efficient mowing. Its powerful engine, designed for reliability and performance, ensures that grass can be cut cleanly and quickly, even in challenging conditions. Users appreciate the intuitive controls that allow for precise maneuvering, making it easy to navigate around obstacles like trees and flower beds. The ZXT54 also includes features such as a comfortable seat and ergonomic handle grips, enhancing operator comfort during extended use.

Moving to the ZT60, this model takes it a step further with a 60-inch cutting deck. This increased size makes it ideal for large lawns or commercial properties, allowing more area to be covered in less time. The ZT60 is equipped with advanced mowing technology that ensures an even cut and a clean finish. An adjustable cutting height gives users the flexibility to adapt to different grass types and growth conditions.

The Z52 model is another solid option for users looking for a balance between power and maneuverability. With a 52-inch cutting deck, this model is favored for its agility in tighter spaces while still providing a robust mowing performance. The Z52 boasts some of the latest technological advancements, including a heavy-duty chassis and an efficient engine that prolongs work time and reduces wear.

For smaller properties, the Z44 model shines with its 44-inch deck, making it perfect for navigating narrow spaces without compromising on cutting performance. Its compact size does not sacrifice power, as it is outfitted with a capable engine that can handle various grass types while providing a reliable performance.

Finally, the ZT72 model, with its impressive 72-inch cutting deck, is engineered specifically for extensive commercial use. It is built to withstand demanding conditions, featuring heavy-duty components that ensure longevity. The ZT72 also includes advanced features like an enhanced mulching option and a robust suspension system, providing a smooth ride over uneven terrain.

In summary, the Land Pride ZXT54, ZT60, Z52, Z44, and ZT72 models each offer unique features tailored to meet the varying needs of users. Whether for residential use or commercial applications, these mowers deliver power, efficiency, and unmatched comfort, ensuring that mowing tasks are completed effectively and with ease.