Land Pride Z52 , Z60, Z72 manual Access to Engine and Hydraulic Pumps, Hydraulic System

Page 36

Land Pride

Section 4 Maintenance and Lubrication

cleanliness and tightness of the terminals and ground connections. A general understanding of electrical servicing and use of basic test equipment is necessary for troubleshooting and repair.

Major overhaul or repair of the starting motor or alternator should be performed by trained technicians only.

Access to Engine and Hydraulic Pumps

The hydraulic pumps are accessed by lifting the seat platform. The seat platform is hinged at the front. To raise it, release seat latch and tilt seat platform up and forward. The seat platform catch (See Figure 4-4) will prevent the seat from going all the way over. However, if more access is desired under the seat platform, the seat platform catch can be raised allowing the seat to pivot more. Make certain to place the control arms in the park brake position and lift the seat arms before raising the seat.

Seat Platform

Seat Platform Catch

 

Control Lever

Access to Engine and Hydraulic Pumps

19070

 

Figure 4-4

 

!WARNING!

Always wear adequate eye protection when servicing the hydraulic system and battery.

Hydraulic System

IMPORTANT: Never use hydraulic or automatic transmission fluid in this system; use only motor oil as specified. Remember, dirt is the primary enemy of any hydraulic system.

!WARNING!

Hydraulic oil escaping under pressure can penetrate skin. Hydraulic oil may cause infection in a minor cut or opening in

the skin. If exposed to hydraulic fluid, see a doctor at once. Before applying pressure to hydraulic system, make sure all connections are tight and all hoses and lines are in good condition. To find a leak under pressure, use a piece of cardboard or wood, never use your hands. Relieve all pressure in the system before disconnecting or working on hydraulic lines. To relieve pressure, place control levers in park.

The 1.0 U.S. gallon (3.79 liter) hydraulic reservoir is located in front of the engine and under the operator’s platform. See Figure 4-5.

Hydraulic Reservoir

Hydraulic Filter

Hydraulic Reservoir and Filter

19069

Figure 4-5

 

Check oil level in hydraulic system after every 50 hours of operation or weekly, whichever occurs first. Check more often if system appears to be leaking or otherwise malfunctioning.

Fluid level should be 1” from top of reservoir. Use only SAE 10W40 SG, SF/CC, CD service motor oil.

Change hydraulic system filter element (Land Pride P/N 831-030C) (Fig. 4-5) after first 50 hours of mower operation, then replace filter and oil in reservoir every 500 hours thereafter. When changing hydraulic oil use 1/2 unit (approximately 3.5 oz.) of Lubrizol additive (Land Pride P/N 821-041C). This additive, available from your Land Pride dealer, will increase the performance life of the hydraulic system components.

The system filter is located directly in front of the hydraulic reservoir. A standard oil filter wrench is used to change filter, threads are right handed. Use an Accu Z approved filter element only (Land Pride P/N 831-030C).

IMPORTANT: Pre-fill the filter element with clean oil, before installing, to prevent drawing air into the system pump.

34 Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M

03/11/03

Image 36
Contents Accu-Z Table of Contents Be Aware of Signal Words Keep Riders Off MachineryFor Your Protection Shutdown and StoragePractice Safe Maintenance Safety at All TimesPrepare for Emergencies Wear Protective EquipmentAvoid High Pressure Fluids Hazard Important Safety Information 838-303C838-307C 838-308C 838-310C 838-399CUsing This Manual ApplicationOwner Assistance IntroductionControl Lever and Seat Assembly Remote Air Cleaner AssemblyAssembly and Set-Up Remote Air Cleaner Assembly Optional Equipment AssembliesControl Lever Extensions Accu-Vac Assembly Mower Deck PreparationBlower, Pulley and Pulley Cover Assembly Blower Drive BeltBagger Assembly Bagger Assembly Ignition Switch ControlsOperation Throttle ControlBlade Engagement Switch Control LeversDeck Height Deck Lift Locking Pin Control LeversSafety Start Interlock System InstrumentationEngine Starting Hour MeterMoving Mower with Stalled Engine Front of mower Faces This DirectionDriving the Mower Operating SuggestionsSteering To Stop or Decrease SpeedMower Deck Operation Operating Instructions Adjustments Torque ValuesSteering Linkage Control Lever Park Brake SlotControl Lever Neutral Adjustment Jam NutStop Control Lever Reverse Spring Adjustment Control Lever StopsTop Nylock Nut Reverse Spring Nylock Nut LinkagePark Brake Adjustment Control Lever AdjustmentSteering Dampener Steering Dampener Upper Control Lever Cap Screw LowerFront Brake Link Right Side Control Lever Park Brake Slot Outside Edge Travel SlotBy-Pass Valve Jam Nut Brake Linkage TurnbuckleHydraulic Pump Belt Adjustment Deck Drive Belt AdjustmentEngine RPM Setting Deck Leveling and Height AdjustmentStop Handle Height Adjusting Blocks Deck Level AdjustmentsDeck Lift Threaded Rod Nut Nut Chain Bolt Adjuster Jam Nut Hardware Deck Lift Threaded Rod Foot Pedal Nut Nut ChainLift Block Deck Lift Rod Assist Springs Deck Cutting Height Adjustment Height Adjusting Stop PlateAnti-Scalp Rollers Adjusting Holes Anti-Scalp RollersMaintenance and Lubrication Top View Deck Top View Bottom ViewMaintenance Schedule Maintenance Refer to Tire Inflation ChartTires Torque ValuesBattery Hour MeterLubrication Electrical System Access to Engine and Hydraulic Pumps Hydraulic SystemSeat Platform Seat Platform Catch Control Lever Hydraulic Reservoir Hydraulic FilterFuel System Engine Oil and FilterFuel Filter Improper Installation Engine Air FilterEngine Oil Filler Tube Oil Filter Drain Plug Over ServicingEngine Air Filter Service Procedure General Engine MaintenanceDamaged Filter, Seals or Canister Incorrect Air Filter ElementBelt Replacement Mower Blade MaintenanceMower Blade Removal Lift Jack OptionPreparation of Engine for Storage New Season PreparationSpecifications and Capacities Safety Features IndicatorsWeight Kit ParkingFeatures and Benefits 52, 60 or 72 Cutting widthTroubleshooting Tire Inflation Chart AppendixTire Inflation PSIWarranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 6 pages 11.76 Kb

Z60, Z52, Z52 , Z60, Z72 specifications

Land Pride is a recognized leader in the manufacturing of high-quality outdoor equipment, particularly known for their commercial mowers. Among their lineup, models like the ZXT54, ZT60, Z52, Z44, and ZT72 stand out for their commitment to performance, durability, and ease of use. These zero-turn mowers are designed to tackle a variety of mowing tasks, making them ideal for both residential and commercial applications.

The Land Pride ZXT54 model features a 54-inch cutting deck, which provides ample width for efficient mowing. Its powerful engine, designed for reliability and performance, ensures that grass can be cut cleanly and quickly, even in challenging conditions. Users appreciate the intuitive controls that allow for precise maneuvering, making it easy to navigate around obstacles like trees and flower beds. The ZXT54 also includes features such as a comfortable seat and ergonomic handle grips, enhancing operator comfort during extended use.

Moving to the ZT60, this model takes it a step further with a 60-inch cutting deck. This increased size makes it ideal for large lawns or commercial properties, allowing more area to be covered in less time. The ZT60 is equipped with advanced mowing technology that ensures an even cut and a clean finish. An adjustable cutting height gives users the flexibility to adapt to different grass types and growth conditions.

The Z52 model is another solid option for users looking for a balance between power and maneuverability. With a 52-inch cutting deck, this model is favored for its agility in tighter spaces while still providing a robust mowing performance. The Z52 boasts some of the latest technological advancements, including a heavy-duty chassis and an efficient engine that prolongs work time and reduces wear.

For smaller properties, the Z44 model shines with its 44-inch deck, making it perfect for navigating narrow spaces without compromising on cutting performance. Its compact size does not sacrifice power, as it is outfitted with a capable engine that can handle various grass types while providing a reliable performance.

Finally, the ZT72 model, with its impressive 72-inch cutting deck, is engineered specifically for extensive commercial use. It is built to withstand demanding conditions, featuring heavy-duty components that ensure longevity. The ZT72 also includes advanced features like an enhanced mulching option and a robust suspension system, providing a smooth ride over uneven terrain.

In summary, the Land Pride ZXT54, ZT60, Z52, Z44, and ZT72 models each offer unique features tailored to meet the varying needs of users. Whether for residential use or commercial applications, these mowers deliver power, efficiency, and unmatched comfort, ensuring that mowing tasks are completed effectively and with ease.