Land Pride 22081, 720-132M General Maintenance, Prepare Vehicle for Maintenance, Torque Values

Page 26

Table of Contents

Section 6 Maintenance

General Maintenance

!WARNING

Read and observe all safety warnings in this manual and in the engine service manual.

Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Land Pride dealer when assistance is needed.

!WARNING

Except when checking or changing components, always keep protective shields on for safety as well as for cleanliness.

!WARNING

Keep engine clean of oil, grease, trash and debris which can cause engine overheating, fires and belt wear. Clean only after the engine has completely cooled. Wear gloves to protect hands from cuts, puncture wounds and burns.

!WARNING

DO NOT have engine running when servicing or making adjustments to the vehicle. Shut engine off, place transmission in gear, set park brake and remove ignition switch key for maximum safety.

!DANGER

Repairs or maintenance specifically requiring engine power should be performed by trained personnel only. Transmission gear should be set in neutral with tires properly chocked or with drive tires properly supported off the floor. Enclosed areas should be properly ventilated to prevent carbon monoxide poisoning.

!DANGER

Exercise extreme caution when working with and around the driveshaft and power steering belt. Make certain the engine cannot be accidentally started. Shut engine off and remove ignition switch key for maximum safety. Repairs or maintenance requiring engine power should be performed by trained personnel only.

Regular maintenance is the best prevention for costly downtime or expensive, premature repair. The following pages contain suggested maintenance information and schedules which the operator should follow on a routine basis.

Remain alert for unusual noises, they could be signaling a problem. Visually inspect the vehicle for any abnormal wear or damage. A good time to detect potential problems is while performing scheduled maintenance service. Correcting the problem as quickly as possible is the best insurance.

Prepare Vehicle for Maintenance

Before servicing the vehicle the following procedure must be followed to secure the vehicle:

1.Park vehicle on a level surface. Don’t work under or around a vehicle parked on a steep incline.

2.Place gear selector in 1st or reverse.

3.Set park brake.

4.Turn ignition switch off and remove switch key.

5.Block pinch point area at the center swivel yoke to prevent movement. (See DANGER below.)

6.Chock front and back side of the wheels not being raised off the ground whenever jacking a vehicle or when ground surface slopes.

7.Always use jack stands to support the vehicle when working under the vehicle.

!DANGER

Pivoting about the center swivel yoke must be blocked to prevent movement before working on or around the vehicle. This articulation area is an extremely dangerous pinch point area caused by just a slight turning of the steering wheel even when the vehicle is not running.

Torque Values

Wheel Lug Nuts

!WARNING

Particular attention must be given to tightening the wheel lug nuts. Failure to correctly torque these items may result in the loss of a wheel, which can cause personal injury and damage to the vehicle.

Torque Values

 

FT -lbs.

Nm

 

 

 

Wheel lug nuts

65 - 75

88.14 - 101.7

 

 

 

Always check wheel lug nut torque values two hours after initial operation and two hours after each tire repair and/or replacement. Routinely check lug nut torque valves every 100 hours of operation. See "Maintenance Schedule" on page 32.

24

4400EX Heavy Duty Off Road Utility Vehicle 720-132M

7/01/05

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Gondo Table of Contents Application Safety FirstUsing This Manual IntroductionSerial Number Plate Land Pride Service Department East North StreetOwner Assistance Product SupportImportant Safety Information Safety SymbolBe Aware of Signal Words For Your ProtectionPrepare for Emergencies Practice Safe MaintenanceTire Safety Wear Protective EquipmentSafe Operating Procedures Table of Contents Safety Decals 818-543C838-492C 838-629C 838-486C 838-490C 838-628C 838-667C838-688C Machine RolloverPre-Delivery and Check List Dealer Service and Inspection ListPre-Delivery Certificate Vehicle InformationDealer Delivery To Customer List Customer Acceptance ListOperating Instructions Operator ResponsibilitiesGeneral Operation Foot Operated Controls Hand Operated Controls Engine Hood ReleaseSeat Belt Components Fuel IndicatorSteering Seat BeltsDriving Conditions Pulling Loads Towing the GondoTraverse Traveling on Steep Hills Towing Without a TrailerPlan Your Route Traveling Tips From the Trail MastersPreparation and Planning Plan Your GearTable of Contents Dump Bed Option Options and AccessoriesGondo Options Tailgate Operation Cargo box option onlyGondo Accessories Maintenance General MaintenancePrepare Vehicle for Maintenance Torque ValuesJacking the Vehicle Tire MaintenanceTire Inflation Chart Inflation PSI Front Tires Rear Tires Seat BeltsElectrical System BatteryJump Starting the Battery Prepare Vehicle to Jump-StartFuel System Disconnecting Jumper CablesConnecting Jumper Cables Emptying the Fuel Tank Fuel Filter and Fuel Line MaintenanceFilling the Fuel Tank General Information Engine MaintenancePower Steering Belt High Altitude Carburetor KitPrecleaner Foam Element Air Filter Maintenance ScheduleAir Filter Replacement Parts Engine Air FilterSpark Arrester Replacement Parts Spark Arrester Maintenance ScheduleSpark Arrester Maintenance Procedure Spark ArresterMaintenance Schedule Lubrication and Fluids Engine Oil Maintenance ScheduleEngine Oil Engine Oil Type and CapacityRefer to Figures 7-1, 7-2, 7-3, 7-4 Engine Oil and Filter ChangeLand Pride Oil Filter Differential Oil Level Check Differential Maintenance ScheduleDifferential Oil Type and Capacity Differential Oil ChangeTransmission Fluid Type and Capacity Transmission Maintenance ScheduleTransmission Fluid Transmission Oil Level CheckBrake Fluid Steering & Cargo Lift Cylinder FluidPillow Block Bearing Grease Type LubricationDriveline U-Joints Rotating Bearing SurfacesVehicle Storage Preparation Seasonal StorageEngine Preparation for Storage Vehicle Removal From Storage PreparationScratch IntroductionLight Scuff Body RepairDeep Gouge Specifications and Capacities 4400EX Series GondoTable of Contents Troubleshooting Engine overheats Engine runs unevenlyPark brake doesn’t work Engine stops runningGear Shift is malfunctioning Starter cranks slowlyVehicle speed does not reach 17 MPH Steering does not track correctlySteering play is excessive Vehicle looses ground speed withoutIn-tpi Ft-lb Torque Values ChartAppendix Land Pride Limited Warranty Utility VehicleCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

22081, 22076, 720-132M specifications

Land Pride is renowned for its high-quality agricultural and landscaping equipment, and among its impressive lineup, the Land Pride 720-132M mower stands out as a versatile solution for various mowing applications. Designed with performance and efficiency in mind, the 720-132M mower is perfect for both residential and commercial users looking for a reliable machine capable of handling diverse terrain and mowing conditions.

One of the key features of the 720-132M is its robust cutting deck, which measures 132 inches in width. This wide cutting capability allows for expansive mowing coverage in fewer passes, significantly reducing mowing time and increasing productivity. The deck is constructed from heavy-duty materials, ensuring durability and longevity even when used in challenging environments.

Equipped with a high-performance cutting system, the mower boasts engineered blades that provide a clean and precise cut, promoting healthier lawn growth. The unique blade overlap design ensures consistent cutting performance across the entire width of the deck, reducing the likelihood of uncut areas left behind.

The Land Pride 720-132M features adjustable cutting height settings, giving operators the flexibility to adapt the mower to various grass types and desired finish quality. This adjustability is crucial for achieving optimal results, especially when transitioning from different mowing conditions.

Safety is a top priority for Land Pride, and the 720-132M integrates several safety features to protect both the operator and the equipment. Its robust frame design provides stability during operation, while operator presence controls ensure the mower stops when the operator leaves the seat, mitigating the risk of unintended accidents.

The mower is compatible with a wide range of tractors, allowing for seamless integration with existing equipment. Its simple attachment system enables quick mounting and dismounting, making it user-friendly and convenient for varying mowing tasks.

Another notable technology in the 720-132M is its efficient power transfer system. The mower is designed to maximize performance while minimizing wear and tear on the tractor, ensuring that operators can tackle their mowing tasks with confidence and ease.

Overall, the Land Pride 720-132M mower, with its advanced technologies and features, stands out as a leading choice for those seeking reliable and efficient mowing solutions tailored to both professional and personal landscaping needs.
Top Page Image Contents