Land Pride 720-132M, 22076, 22081 manual Introduction, Light Scuff, Scratch, Body Repair

Page 42

Table of Contents

Section 9 Body Repair

Introduction

Land Pride Gondo bodies are constructed of fiberglass. Scuffs, light scratches and deep gouges are in most situations repairable. Land Pride recommends that you use a professional body shop to restore your vehicle’s body. For your consideration, we have provided below a list of recommended tools, materials and steps suggested for repairing the fiberglass body.

NOTE: Land Pride does not supply the required tools, paint and materials needed to repair the vehicle body. All tools, paint and materials should be purchased locally.

Light Scuff

Required Tools and Materials

(See note above)

•1,000 rpm buffing tool, DeWalt #849

•Meguiars buffing compound #8432

•Meguiars polish #8232 (optional)

•Meguiars maroon cutting pad #W-7006

•Meguiars tan polishing pad #W-9006 (optional)

•Meguiars backing plate #W-64

•Soft clean cotton cloths

Steps to Repair

1.Clean entire area of repair. Clean water is fine for this purpose. Do not use solvent as this will damage the body surface.

2.Install cutting pad #7006 on buffer (maroon pad).

3.Spread compound on area of repair, use about as much as it takes to cover a half-dollar coin, this is a good starting point.

4.Set buffing tool to lowest possible speed on dial, do not buff at a high speed as this will heat and warp material.

5.Buff damage area until surface scuff disappears. A second and third application of compound may be required. Keep buffer moving over surface, this will help keep the surface cool. Clean compound residue off surface after each buffing operation. Do not continue to buff compound until dry, or buff the surface when dry. When all scuff marks have been buffed out the surface may still appear a little dull, if so, proceed to #6.

6.Install polish on surface as in step #3.

7.Spread #8232 polish on surface as in step #3.

8.Polish to a high luster or as required to match surrounding material.

9.Wipe clean with soft clean cloth; any dirt on cloth will mar surface.

Scratch

Required Tools and Materials

(See note to left)

•1,000 rpm buffing tool, DeWalt #849

•Meguiars buffing compound #8432

•Meguiars polish #8232 (optional)

•Meguiars maroon cutting pad #W-7006

•Meguiars tan polishing pad #W-9006 (optional)

•Meguiars backing plate #W-64

•Soft clean cotton cloths

•3M interface sanding pad #05774

•Air Vantage finishing sander with 6-inch hook and loop pad

•3M-P800 sanding film #00970

Steps to Repair

1.Clean entire area of repair. Clean water is fine for this purpose. Do not use solvent as this will damage the body surface.

2.Install interface-sanding pad onto finishing sander. Attach sanding film to Interface pad. (Take care in centering sanding pad and film on sander.)

3.Sand surface using about 45 P.S.I. air pressure at tool inlet, do not sand at a high pad speed, because speed causes the sanding film to load with dust and heats the body surface. Proper sander pad speed is based on cut and travel speed of pad, and downward pressure applied by the operator. To clean sanding pad surface, run sander face at 90 degrees on the edge of a piece of cardboard. This cleaning operation will help keep the sanding film clean and run cooler. Continue to sand surface until original scratch damage is no longer visible. Wipe the surface with a cloth then inspect to be sure the entire original scratch has been fully sanded away (very important).

4.Install cutting pad #7006 on buffer (maroon pad).

5.Spread compound #8432 on area of repair, use about as much as it takes to cover a half-dollar coin, this is a good starting point.

6.Set buffing tool to lowest possible speed on dial, do not buff at a high speed as this will heat and warp material.

7.Buff sanded area until surface scuff disappears.

40

4400EX Heavy Duty Off Road Utility Vehicle 720-132M

7/01/05

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Gondo Table of Contents Application Safety FirstUsing This Manual IntroductionSerial Number Plate Land Pride Service Department East North StreetOwner Assistance Product SupportImportant Safety Information Safety SymbolBe Aware of Signal Words For Your ProtectionPrepare for Emergencies Practice Safe MaintenanceTire Safety Wear Protective EquipmentSafe Operating Procedures Table of Contents Safety Decals 818-543C838-492C 838-629C 838-486C 838-490C 838-628C 838-667C838-688C Machine RolloverPre-Delivery and Check List Dealer Service and Inspection ListPre-Delivery Certificate Vehicle InformationDealer Delivery To Customer List Customer Acceptance ListOperator Responsibilities General OperationOperating Instructions Foot Operated Controls Hand Operated Controls Engine Hood ReleaseSeat Belt Components Fuel IndicatorSteering Seat BeltsDriving Conditions Pulling Loads Towing the GondoTraverse Traveling on Steep Hills Towing Without a TrailerPlan Your Route Traveling Tips From the Trail MastersPreparation and Planning Plan Your GearTable of Contents Dump Bed Option Options and AccessoriesGondo Options Tailgate Operation Cargo box option onlyGondo Accessories Maintenance General MaintenancePrepare Vehicle for Maintenance Torque ValuesJacking the Vehicle Tire MaintenanceTire Inflation Chart Inflation PSI Front Tires Rear Tires Seat BeltsElectrical System BatteryJump Starting the Battery Prepare Vehicle to Jump-StartDisconnecting Jumper Cables Connecting Jumper CablesFuel System Fuel Filter and Fuel Line Maintenance Filling the Fuel TankEmptying the Fuel Tank General Information Engine MaintenancePower Steering Belt High Altitude Carburetor KitPrecleaner Foam Element Air Filter Maintenance ScheduleAir Filter Replacement Parts Engine Air FilterSpark Arrester Replacement Parts Spark Arrester Maintenance ScheduleSpark Arrester Maintenance Procedure Spark ArresterMaintenance Schedule Lubrication and Fluids Engine Oil Maintenance ScheduleEngine Oil Engine Oil Type and CapacityEngine Oil and Filter Change Land Pride Oil FilterRefer to Figures 7-1, 7-2, 7-3, 7-4 Differential Oil Level Check Differential Maintenance ScheduleDifferential Oil Type and Capacity Differential Oil ChangeTransmission Fluid Type and Capacity Transmission Maintenance ScheduleTransmission Fluid Transmission Oil Level CheckBrake Fluid Steering & Cargo Lift Cylinder FluidPillow Block Bearing Grease Type LubricationDriveline U-Joints Rotating Bearing SurfacesVehicle Storage Preparation Seasonal StorageEngine Preparation for Storage Vehicle Removal From Storage PreparationScratch IntroductionLight Scuff Body RepairDeep Gouge Specifications and Capacities 4400EX Series GondoTable of Contents Troubleshooting Engine overheats Engine runs unevenlyPark brake doesn’t work Engine stops runningGear Shift is malfunctioning Starter cranks slowlyVehicle speed does not reach 17 MPH Steering does not track correctlySteering play is excessive Vehicle looses ground speed withoutTorque Values Chart AppendixIn-tpi Ft-lb Land Pride Limited Warranty Utility VehicleCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

22081, 22076, 720-132M specifications

Land Pride is renowned for its high-quality agricultural and landscaping equipment, and among its impressive lineup, the Land Pride 720-132M mower stands out as a versatile solution for various mowing applications. Designed with performance and efficiency in mind, the 720-132M mower is perfect for both residential and commercial users looking for a reliable machine capable of handling diverse terrain and mowing conditions.

One of the key features of the 720-132M is its robust cutting deck, which measures 132 inches in width. This wide cutting capability allows for expansive mowing coverage in fewer passes, significantly reducing mowing time and increasing productivity. The deck is constructed from heavy-duty materials, ensuring durability and longevity even when used in challenging environments.

Equipped with a high-performance cutting system, the mower boasts engineered blades that provide a clean and precise cut, promoting healthier lawn growth. The unique blade overlap design ensures consistent cutting performance across the entire width of the deck, reducing the likelihood of uncut areas left behind.

The Land Pride 720-132M features adjustable cutting height settings, giving operators the flexibility to adapt the mower to various grass types and desired finish quality. This adjustability is crucial for achieving optimal results, especially when transitioning from different mowing conditions.

Safety is a top priority for Land Pride, and the 720-132M integrates several safety features to protect both the operator and the equipment. Its robust frame design provides stability during operation, while operator presence controls ensure the mower stops when the operator leaves the seat, mitigating the risk of unintended accidents.

The mower is compatible with a wide range of tractors, allowing for seamless integration with existing equipment. Its simple attachment system enables quick mounting and dismounting, making it user-friendly and convenient for varying mowing tasks.

Another notable technology in the 720-132M is its efficient power transfer system. The mower is designed to maximize performance while minimizing wear and tear on the tractor, ensuring that operators can tackle their mowing tasks with confidence and ease.

Overall, the Land Pride 720-132M mower, with its advanced technologies and features, stands out as a leading choice for those seeking reliable and efficient mowing solutions tailored to both professional and personal landscaping needs.
Top Page Image Contents