Land Pride 720-132M, 22076, 22081 manual Hand Operated Controls, Engine Hood Release

Page 18

Table of Contents

Section 4 Operating Instructions

!DANGER

Sudden hard braking pressure can throw occupants forward causing body injury and death. Whenever possible, apply pressure to the brake pedal gently and increase presser slowly until desired braking force is achieved.

#11 Brake Pedal: Slows vehicle speed quickly and stops vehicle. Slow vehicle speed quickly by removing your foot from the accelerator pedal and then apply pressure to the brake pedal. Apply clutch and brake pedal before coming to a complete stop.

NOTE: Do not rest foot on brake pedal while driving vehicle except when slowing or stopping. Pressure on the brake pedal will shorten life expectancy of brake liners.

Hand Operated Controls

Refer to Figure 4-3

#12 Park Brake Lever: The park brake lever is located on the floor board right of the operator and should be set at all times the vehicle is not in operation. Push the lever forward to the horizontal position to set the brake. Release the brake by pulling back on the lever to the vertical position. Do not drive vehicle with park brake on.

The knob on the end of the handle may be turned to make minor adjustments to the braking capabilities. Major adjustments should be made at either end of the brake cable.

#13 Dump Lever: Dump lever activates the hydraulic cylinder to raise and lower the cargo box. Pull lever back to raise cargo box. Push lever forward to lower cargo box.

#14 Auxiliary Lever: Auxiliary lever is used to operate a hydraulic cylinder on a front mounted snow blade or to operate equipment pulled by the Gondo.

Additional accessories must be purchased to make hydraulic connections.

IMPORTANT: Release dump lever immediately when cargo box is fully up or down to extend hydraulic seal life and to prevent overheating.

#15 Gear Shift Lever: Changes transmission gears from neutral to one of the five forward speeds or reverse. Always start engine with gear shift in neutral. Follow the shift pattern on the shift lever to find your selected gear.

Always start in first gear when under load or on an incline. You may start in second gear if on the level with no load and no incline. Shift up to the next higher

gear only after reaching sufficient speed and engine RPM. Continue shifting up to the next higher gear until highest gear is reached. Shift down one or two gears if loss of engine power is noticed.

Always place gearshift in first gear when descending a steep grade under load to make use of the additional braking force provided by the engine.

15

Knob

12

14

13

22061

Figure 4-3

Engine Hood Release

Refer to Figure 4-4

#16 Hood Release Lever: The Hood release lever is located under the driver seat on the left hand side. Pull back on the lever and lift up on the engine hood.

#17 Hood Support Rod: Secures the engine hood in the raised position by placing the hood support rod in the socket as shown.

#18 Hood Latch: Secures the hood in the lowered position. Lift up on the hood and return the support rod down to its stored position. Lower the hood until the latch rod is secured by the hood latch (#18).

Latch Rod

17

Socket

16

18

22070

Figure 4-4

16

4400EX Heavy Duty Off Road Utility Vehicle 720-132M

7/01/05

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Gondo Table of Contents Application Safety FirstUsing This Manual IntroductionSerial Number Plate Land Pride Service Department East North StreetOwner Assistance Product SupportImportant Safety Information Safety SymbolBe Aware of Signal Words For Your ProtectionPrepare for Emergencies Practice Safe MaintenanceTire Safety Wear Protective EquipmentSafe Operating Procedures Table of Contents Safety Decals 818-543C838-492C 838-629C 838-486C 838-490C 838-628C 838-667C838-688C Machine RolloverPre-Delivery and Check List Dealer Service and Inspection ListPre-Delivery Certificate Vehicle InformationDealer Delivery To Customer List Customer Acceptance ListOperator Responsibilities General OperationOperating Instructions Foot Operated Controls Hand Operated Controls Engine Hood ReleaseSeat Belt Components Fuel IndicatorSteering Seat BeltsDriving Conditions Pulling Loads Towing the GondoTraverse Traveling on Steep Hills Towing Without a TrailerPlan Your Route Traveling Tips From the Trail MastersPreparation and Planning Plan Your GearTable of Contents Dump Bed Option Options and AccessoriesGondo Options Tailgate Operation Cargo box option onlyGondo Accessories Maintenance General MaintenancePrepare Vehicle for Maintenance Torque ValuesJacking the Vehicle Tire MaintenanceTire Inflation Chart Inflation PSI Front Tires Rear Tires Seat BeltsElectrical System BatteryJump Starting the Battery Prepare Vehicle to Jump-StartDisconnecting Jumper Cables Connecting Jumper CablesFuel System Fuel Filter and Fuel Line Maintenance Filling the Fuel TankEmptying the Fuel Tank General Information Engine MaintenancePower Steering Belt High Altitude Carburetor KitPrecleaner Foam Element Air Filter Maintenance ScheduleAir Filter Replacement Parts Engine Air FilterSpark Arrester Replacement Parts Spark Arrester Maintenance ScheduleSpark Arrester Maintenance Procedure Spark ArresterMaintenance Schedule Lubrication and Fluids Engine Oil Maintenance ScheduleEngine Oil Engine Oil Type and CapacityEngine Oil and Filter Change Land Pride Oil FilterRefer to Figures 7-1, 7-2, 7-3, 7-4 Differential Oil Level Check Differential Maintenance ScheduleDifferential Oil Type and Capacity Differential Oil ChangeTransmission Fluid Type and Capacity Transmission Maintenance ScheduleTransmission Fluid Transmission Oil Level CheckBrake Fluid Steering & Cargo Lift Cylinder FluidPillow Block Bearing Grease Type LubricationDriveline U-Joints Rotating Bearing SurfacesVehicle Storage Preparation Seasonal StorageEngine Preparation for Storage Vehicle Removal From Storage PreparationScratch IntroductionLight Scuff Body RepairDeep Gouge Specifications and Capacities 4400EX Series GondoTable of Contents Troubleshooting Engine overheats Engine runs unevenlyPark brake doesn’t work Engine stops runningGear Shift is malfunctioning Starter cranks slowlyVehicle speed does not reach 17 MPH Steering does not track correctlySteering play is excessive Vehicle looses ground speed withoutTorque Values Chart AppendixIn-tpi Ft-lb Land Pride Limited Warranty Utility VehicleCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

22081, 22076, 720-132M specifications

Land Pride is renowned for its high-quality agricultural and landscaping equipment, and among its impressive lineup, the Land Pride 720-132M mower stands out as a versatile solution for various mowing applications. Designed with performance and efficiency in mind, the 720-132M mower is perfect for both residential and commercial users looking for a reliable machine capable of handling diverse terrain and mowing conditions.

One of the key features of the 720-132M is its robust cutting deck, which measures 132 inches in width. This wide cutting capability allows for expansive mowing coverage in fewer passes, significantly reducing mowing time and increasing productivity. The deck is constructed from heavy-duty materials, ensuring durability and longevity even when used in challenging environments.

Equipped with a high-performance cutting system, the mower boasts engineered blades that provide a clean and precise cut, promoting healthier lawn growth. The unique blade overlap design ensures consistent cutting performance across the entire width of the deck, reducing the likelihood of uncut areas left behind.

The Land Pride 720-132M features adjustable cutting height settings, giving operators the flexibility to adapt the mower to various grass types and desired finish quality. This adjustability is crucial for achieving optimal results, especially when transitioning from different mowing conditions.

Safety is a top priority for Land Pride, and the 720-132M integrates several safety features to protect both the operator and the equipment. Its robust frame design provides stability during operation, while operator presence controls ensure the mower stops when the operator leaves the seat, mitigating the risk of unintended accidents.

The mower is compatible with a wide range of tractors, allowing for seamless integration with existing equipment. Its simple attachment system enables quick mounting and dismounting, making it user-friendly and convenient for varying mowing tasks.

Another notable technology in the 720-132M is its efficient power transfer system. The mower is designed to maximize performance while minimizing wear and tear on the tractor, ensuring that operators can tackle their mowing tasks with confidence and ease.

Overall, the Land Pride 720-132M mower, with its advanced technologies and features, stands out as a leading choice for those seeking reliable and efficient mowing solutions tailored to both professional and personal landscaping needs.
Top Page Image Contents