Land Pride 22076, 720-132M, 22081 manual Deep Gouge

Page 43

Table of Contents

Section 9 Body Repair

8.A second and third application of compound may be required. Keep buffer moving over surface, this will help keep the surface cool. Clean compound residue off surface after each buffing operation. Do not continue to buff compound until dry.

9.Buff the surface of the body when dry. When all scuff marks have been buffed out the surface may still appear a little dull, if so, proceed to #10.

10.Install polishing pad #W-9006 on buffer (tan pad).

11.Spread #8232 polish on surface as in step #3.

12.Polish to a high luster or as required to match surrounding material.

13.Wipe clean with soft clean cloth; any dirt on cloth will mar surface.

Deep Gouge

Required Tools and Materials

(See note on page 39)

•1,000 rpm buffing tool, DeWalt #849

•Evercoat Body Filler Easy Sand

•Sanding Pad

•DuPont Full-Thane Primer 421-15

•DuPont 3939 Cleaner

•DuPont Sealer 42470

•DuPont Chroma Base/ Clear Coat Paint System

•HVLP Paint Sprayer

Steps to Repair

1.Sand damaged area with 500-grit paper to remove raised edges and to create abraded surface for proper adhesion.

2.Fill damaged area with Evercoat body filler (2-part system) and allow to completely dry.

3.Sand down high spots with 500-grit paper. If recesses are still visible due to filler shrinkage, apply second skim coat and again allow to dry completely, then sand surface flush with surrounding area.

4.Apply DuPont Full-Thane Primer 421-15 over body filler.

5.Once primer is completely dry, clean surface with DuPont 3939 Cleaner and again allow surface to dry completely.

6.Apply 42470 Sealer over body filler.

7.Apply color-matched paint system with HVLP paint sprayer according to supplier’s recommendations.

7/01/05

4400EX Heavy Duty Off Road Utility Vehicle 720-132M 41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Gondo Table of Contents Introduction Safety FirstUsing This Manual ApplicationProduct Support Land Pride Service Department East North StreetOwner Assistance Serial Number PlateFor Your Protection Safety SymbolBe Aware of Signal Words Important Safety InformationWear Protective Equipment Practice Safe MaintenanceTire Safety Prepare for EmergenciesSafe Operating Procedures Table of Contents 818-543C Safety Decals838-492C 838-629C 838-486C 838-667C 838-490C 838-628CMachine Rollover 838-688CVehicle Information Dealer Service and Inspection ListPre-Delivery Certificate Pre-Delivery and Check ListCustomer Acceptance List Dealer Delivery To Customer ListGeneral Operation Operator ResponsibilitiesOperating Instructions Foot Operated Controls Engine Hood Release Hand Operated ControlsSeat Belts Fuel IndicatorSteering Seat Belt ComponentsDriving Conditions Towing Without a Trailer Towing the GondoTraverse Traveling on Steep Hills Pulling LoadsPlan Your Gear Traveling Tips From the Trail MastersPreparation and Planning Plan Your RouteTable of Contents Tailgate Operation Cargo box option only Options and AccessoriesGondo Options Dump Bed OptionGondo Accessories Torque Values General MaintenancePrepare Vehicle for Maintenance MaintenanceSeat Belts Tire MaintenanceTire Inflation Chart Inflation PSI Front Tires Rear Tires Jacking the VehiclePrepare Vehicle to Jump-Start BatteryJump Starting the Battery Electrical SystemConnecting Jumper Cables Disconnecting Jumper CablesFuel System Filling the Fuel Tank Fuel Filter and Fuel Line MaintenanceEmptying the Fuel Tank High Altitude Carburetor Kit Engine MaintenancePower Steering Belt General InformationEngine Air Filter Air Filter Maintenance ScheduleAir Filter Replacement Parts Precleaner Foam ElementSpark Arrester Spark Arrester Maintenance ScheduleSpark Arrester Maintenance Procedure Spark Arrester Replacement PartsMaintenance Schedule Engine Oil Type and Capacity Engine Oil Maintenance ScheduleEngine Oil Lubrication and FluidsLand Pride Oil Filter Engine Oil and Filter ChangeRefer to Figures 7-1, 7-2, 7-3, 7-4 Differential Oil Change Differential Maintenance ScheduleDifferential Oil Type and Capacity Differential Oil Level CheckTransmission Oil Level Check Transmission Maintenance ScheduleTransmission Fluid Transmission Fluid Type and CapacitySteering & Cargo Lift Cylinder Fluid Brake FluidRotating Bearing Surfaces Grease Type LubricationDriveline U-Joints Pillow Block BearingVehicle Removal From Storage Preparation Seasonal StorageEngine Preparation for Storage Vehicle Storage PreparationBody Repair IntroductionLight Scuff ScratchDeep Gouge 4400EX Series Gondo Specifications and CapacitiesTable of Contents Troubleshooting Engine runs unevenly Engine overheatsStarter cranks slowly Engine stops runningGear Shift is malfunctioning Park brake doesn’t workVehicle looses ground speed without Steering does not track correctlySteering play is excessive Vehicle speed does not reach 17 MPHAppendix Torque Values ChartIn-tpi Ft-lb Utility Vehicle Land Pride Limited WarrantyCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

22081, 22076, 720-132M specifications

Land Pride is renowned for its high-quality agricultural and landscaping equipment, and among its impressive lineup, the Land Pride 720-132M mower stands out as a versatile solution for various mowing applications. Designed with performance and efficiency in mind, the 720-132M mower is perfect for both residential and commercial users looking for a reliable machine capable of handling diverse terrain and mowing conditions.

One of the key features of the 720-132M is its robust cutting deck, which measures 132 inches in width. This wide cutting capability allows for expansive mowing coverage in fewer passes, significantly reducing mowing time and increasing productivity. The deck is constructed from heavy-duty materials, ensuring durability and longevity even when used in challenging environments.

Equipped with a high-performance cutting system, the mower boasts engineered blades that provide a clean and precise cut, promoting healthier lawn growth. The unique blade overlap design ensures consistent cutting performance across the entire width of the deck, reducing the likelihood of uncut areas left behind.

The Land Pride 720-132M features adjustable cutting height settings, giving operators the flexibility to adapt the mower to various grass types and desired finish quality. This adjustability is crucial for achieving optimal results, especially when transitioning from different mowing conditions.

Safety is a top priority for Land Pride, and the 720-132M integrates several safety features to protect both the operator and the equipment. Its robust frame design provides stability during operation, while operator presence controls ensure the mower stops when the operator leaves the seat, mitigating the risk of unintended accidents.

The mower is compatible with a wide range of tractors, allowing for seamless integration with existing equipment. Its simple attachment system enables quick mounting and dismounting, making it user-friendly and convenient for varying mowing tasks.

Another notable technology in the 720-132M is its efficient power transfer system. The mower is designed to maximize performance while minimizing wear and tear on the tractor, ensuring that operators can tackle their mowing tasks with confidence and ease.

Overall, the Land Pride 720-132M mower, with its advanced technologies and features, stands out as a leading choice for those seeking reliable and efficient mowing solutions tailored to both professional and personal landscaping needs.
Top Page Image Contents