Land Pride 720-132M, 22076, 22081 manual Filling the Fuel Tank, Emptying the Fuel Tank

Page 30

Table of Contents

Section 6 Maintenance

•Long-term exposure to vapors can cause serious injury and illness.

•Avoid prolonged breathing of vapors.

•Keep face away from nozzle and gas tank opening.

•Keep gas away from eyes and skin.

Filling the Fuel Tank

Refer to Figure 6-4

The fuel tank is located on the left side under the seat console. Total fuel capacity is 8 gallons.

When filling the fuel tank, place gear shift in 1st or reverse gear, set park brake, turn off engine and remove ignition key. Tilt seat console forward to access fuel tank. Clean dirt from around fuel cap, remove cap and begin filling. When finished, screw cap back on securely and wipe up any spilled gasoline. Use regular unleaded gasoline with an octane rating of 87 or higher.

IMPORTANT: Never use methanol, gasoline containing methanol and/or gasohol containing more than 10% ethanol. These fuels can damage the vehicle’s fuel system. Do not mix oil with gasoline.

Using a fuel stabilizer/conditioner in the vehicle can provide benefits such as:

1.Keeps gasoline fresh during storage of 90 days or less. The fuel tank should be emptied for longer storage.

2.Cleans the engine during operation.

3.Eliminates gum-like varnish build-up in the fuel system.

IMPORTANT: Do not use fuel additives containing methanol or ethanol.

Add the correct amount of gas stabilizer/conditioner to the gas. Follow the gas stabilizer/conditioner manufacturer’s directions for best results.

Emptying the Fuel Tank

!DANGER

Never siphon a fuel tank by sucking on a hose with your mouth. Gasoline is a poison. Also fuel vapors and gas are harmful to your lungs and can permanently damage them. Always use a siphon pump.

The fuel tank will need emptying when preparing for long term storage or replacing a damaged one.

1.Prepare vehicle for maintenance as outlined in steps 1-6 on page 24.

2.Follow all Fuel Safety Cautions, Warnings and Dangers.

3.Remove fuel cap and siphon fuel through the fuel fill opening with a siphon pump into an approved gas container. Make sure the container is capable of holding all the gas. Do not dump fuel on the ground.

Fuel Cap andFuel Filter Fuel Fill Opening

Fuel Gauge

22080

Figure 6-4

Fuel Filter and Fuel Line Maintenance

Refer to Figure 6-5

The fuel filter (Land Pride Part No. 831-031C) is installed in the fuel line between the fuel tank and engine and should be replaced annually. At the same time check the fuel line hoses for any cracks or leaks. Inspect and replace fuel filter and fuel lines as follows:

1.Prepare vehicle for maintenance as outlined in steps 1-6 on page 24.

2.Safely secure the seat console in the raised position.

3.Following all Fuel Safety Cautions and Warnings, remove clamps securing the fuel filter and remove fuel filter for inspection.

4.Check fuel filter for sediment and water accumulation. Check fuel lines for cracks and leaks.

5.Replace damaged fuel lines with new ones.

6.Replace fuel filter when sediment or water is present.

7.Reattach fuel filter to fuel line with arrow on the filter pointing in the same direction fuel flows in the line. Fuel flows towards the engine.

8.Install hose clamps around fuel filter.

9.Start vehicle and inspect for fuel leaks along fuel line and fuel filter.

10.Shut off vehicle and remove wheel chocks if used.

22079

Figure 6-5

28

4400EX Heavy Duty Off Road Utility Vehicle 720-132M

7/01/05

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Gondo Table of Contents Application Safety FirstUsing This Manual IntroductionSerial Number Plate Land Pride Service Department East North StreetOwner Assistance Product SupportImportant Safety Information Safety SymbolBe Aware of Signal Words For Your ProtectionPrepare for Emergencies Practice Safe MaintenanceTire Safety Wear Protective EquipmentSafe Operating Procedures Table of Contents Safety Decals 818-543C838-492C 838-629C 838-486C 838-490C 838-628C 838-667C838-688C Machine RolloverPre-Delivery and Check List Dealer Service and Inspection ListPre-Delivery Certificate Vehicle InformationDealer Delivery To Customer List Customer Acceptance ListOperator Responsibilities General OperationOperating Instructions Foot Operated Controls Hand Operated Controls Engine Hood ReleaseSeat Belt Components Fuel IndicatorSteering Seat BeltsDriving Conditions Pulling Loads Towing the GondoTraverse Traveling on Steep Hills Towing Without a TrailerPlan Your Route Traveling Tips From the Trail MastersPreparation and Planning Plan Your GearTable of Contents Dump Bed Option Options and AccessoriesGondo Options Tailgate Operation Cargo box option onlyGondo Accessories Maintenance General MaintenancePrepare Vehicle for Maintenance Torque ValuesJacking the Vehicle Tire MaintenanceTire Inflation Chart Inflation PSI Front Tires Rear Tires Seat BeltsElectrical System BatteryJump Starting the Battery Prepare Vehicle to Jump-StartDisconnecting Jumper Cables Connecting Jumper CablesFuel System Fuel Filter and Fuel Line Maintenance Filling the Fuel TankEmptying the Fuel Tank General Information Engine MaintenancePower Steering Belt High Altitude Carburetor KitPrecleaner Foam Element Air Filter Maintenance ScheduleAir Filter Replacement Parts Engine Air FilterSpark Arrester Replacement Parts Spark Arrester Maintenance ScheduleSpark Arrester Maintenance Procedure Spark ArresterMaintenance Schedule Lubrication and Fluids Engine Oil Maintenance ScheduleEngine Oil Engine Oil Type and CapacityEngine Oil and Filter Change Land Pride Oil FilterRefer to Figures 7-1, 7-2, 7-3, 7-4 Differential Oil Level Check Differential Maintenance ScheduleDifferential Oil Type and Capacity Differential Oil ChangeTransmission Fluid Type and Capacity Transmission Maintenance ScheduleTransmission Fluid Transmission Oil Level CheckBrake Fluid Steering & Cargo Lift Cylinder FluidPillow Block Bearing Grease Type LubricationDriveline U-Joints Rotating Bearing SurfacesVehicle Storage Preparation Seasonal StorageEngine Preparation for Storage Vehicle Removal From Storage PreparationScratch IntroductionLight Scuff Body RepairDeep Gouge Specifications and Capacities 4400EX Series GondoTable of Contents Troubleshooting Engine overheats Engine runs unevenlyPark brake doesn’t work Engine stops runningGear Shift is malfunctioning Starter cranks slowlyVehicle speed does not reach 17 MPH Steering does not track correctlySteering play is excessive Vehicle looses ground speed withoutTorque Values Chart AppendixIn-tpi Ft-lb Land Pride Limited Warranty Utility VehicleCorporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

22081, 22076, 720-132M specifications

Land Pride is renowned for its high-quality agricultural and landscaping equipment, and among its impressive lineup, the Land Pride 720-132M mower stands out as a versatile solution for various mowing applications. Designed with performance and efficiency in mind, the 720-132M mower is perfect for both residential and commercial users looking for a reliable machine capable of handling diverse terrain and mowing conditions.

One of the key features of the 720-132M is its robust cutting deck, which measures 132 inches in width. This wide cutting capability allows for expansive mowing coverage in fewer passes, significantly reducing mowing time and increasing productivity. The deck is constructed from heavy-duty materials, ensuring durability and longevity even when used in challenging environments.

Equipped with a high-performance cutting system, the mower boasts engineered blades that provide a clean and precise cut, promoting healthier lawn growth. The unique blade overlap design ensures consistent cutting performance across the entire width of the deck, reducing the likelihood of uncut areas left behind.

The Land Pride 720-132M features adjustable cutting height settings, giving operators the flexibility to adapt the mower to various grass types and desired finish quality. This adjustability is crucial for achieving optimal results, especially when transitioning from different mowing conditions.

Safety is a top priority for Land Pride, and the 720-132M integrates several safety features to protect both the operator and the equipment. Its robust frame design provides stability during operation, while operator presence controls ensure the mower stops when the operator leaves the seat, mitigating the risk of unintended accidents.

The mower is compatible with a wide range of tractors, allowing for seamless integration with existing equipment. Its simple attachment system enables quick mounting and dismounting, making it user-friendly and convenient for varying mowing tasks.

Another notable technology in the 720-132M is its efficient power transfer system. The mower is designed to maximize performance while minimizing wear and tear on the tractor, ensuring that operators can tackle their mowing tasks with confidence and ease.

Overall, the Land Pride 720-132M mower, with its advanced technologies and features, stands out as a leading choice for those seeking reliable and efficient mowing solutions tailored to both professional and personal landscaping needs.
Top Page Image Contents