Land Pride RCMB6015, RCMB6010 manual Hitch Assembly, Wing Axle Assembly, Hydraulic Plumbing

Page 14

Table of Contents

Section 1: Preparation and Set-up

Land Pride

	1
3	1
	2
	23578

Hitch Assembly Illustration

Figure 1-2

Hitch Assembly

Refer to Figure 1-2:

NOTE: Do not tighten the hardware until assembly is complete.

1.Install left and right leveling rods (#1) to the hitch frame with 3/4” x 1 1/2” clevis pins, 3/4” ﬂat washers, and 1/8” x 1 1/4” cotter pins. Final adjustment should be made when the cutter is attached to the tractor.

2.Install parking jack (#2) to the hitch frame and secure with attached pin (#3). Adjust parking jack to preferred drawbar height.

Wing Axle Assembly

NOTE: Do not tighten the hardware until assembly is complete.

Refer to Figure 1-3

Wing axle locknuts are tightened for shipping purposes.

1.Loosen lock nuts (#1) slightly and rotate wing axles (#2) to install turnbuckles (#3).

2.Remove cap screws and locknuts (#4). Attach turnbuckles (#3) to the wing axles with existing cap screws and lock nuts (#4).

Hydraulic Plumbing

The cutter is equipped with one hydraulic cylinder in the center for lifting the cutter and one on each wing for folding of the wings independently. All cylinders on the cutter are single action (one-way) type and should not be plumbed for two-way operation.

Each duplex outlet on your tractor can perform only one operation. One outlet is needed for lifting the cutter and a second and third for lifting the wings independently of each other.

If the tractor being used does not have the required number of duplex outlets, an optional control valve kit is available from your dealer.

Your Dealer will be able to help you determine the best configuration to match your needs and your tractor.

2

	1
	Turnbuckle (#3)
	to be secured
	between this
4	flange and the
4	one below.

3

23703a

Wing Axle - Turnbuckle Assembly

Figure 1-3

12 RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M

9/04/08

Image 14

Contents Rotary Cutters Table of Contents Safety at All Times Practice Safe Maintenance Use Safety Lights and DevicesUse a Safety Chain Transport Machinery SafelyWear Protective Equipment Tire SafetyPrepare for Emergencies Avoid High Pressure Fluids Hazard818-240C 818-045C818-130C 818-552C Do not Operate 818-540C818-543C 818-561C 818-276C818-840C 818-830C 838-094C 818-556C818-564C 838-588C818-229C 818-230CUsing This Manual Application Owner AssistanceBefore You Start Dealer Assembly & Preparations Pre-Assembly ChecklistTractor Requirements Hydraulic Plumbing Hitch AssemblyWing Axle Assembly Swivel Clevis Hitch Hitch TypesTractor Hook-up to Swivel Clevis Hitch Bar-Tite Clevis HitchDriveline Hook-up Bar-Tite Clevis Hitch Assembly to Tractor TongueTractor Hook-up to Bar-Tite Clevis Hitch Tractor Hookup to Bar-Tite Clevis HitchPTO Driveline Shortening Hydraulic Hook-upRefer to -7on Unhooking From the Cutter Refer to -1& Figure Pre-start ChecklistCutter Set-up For Transporting Transport Bar, Locked PositionOperating Speed & Turning Angle Transporting The CutterCutter Set-up For Field Operation Refer to -1& -2onManual Wing Lift Winch Optional Manual Wing Lift WinchGeneral Operating Instructions Table of Contents Refer to -1, -2& Figure Cutting Height AdjustmentCenter and Wing Section Leveling Refer to -2 on General Maintenance InformationCutter Blade Maintenance Blade RotationType a Clutches Clutch Run-In Drivelines With Slip ClutchesLand Pride Cutter Blade Parts Clutch Disassembly, Inspection & Assembly Refer to -5 & Table BelowType B Clutch Run-In Plate Assembly Type B Clutch AssemblyType B Clutches Clutch Run-In Step Plate DisassemblyType C Clutches Clutch Run-In Refer to -8 View aPlace hub and friction discs into the housing Skid Shoe Maintenance Plate AssemblyLand Pride Skid Shoe Replacement Parts Install end half clamps if availableStorage Tractor MaintenanceWeight Box Skid Shoe Wing Skid ShoeHrs Adjustable TurnbuckleLubrication Points Axle Hub BearingDouble Swivel Clevis Hitch Main HitchWing Hinges Type of Lubrication Multi-purpose GreaseIntermediate Driveline Joints Divider BoxGearbox Type of Lubrication 80-90W EP Quantity = As requiredZerk located through slot in plastic outer tubes Conventional Driveline Profile TubesConventional Driveline Joints & Shields Drivelines with internal profile tube grease pointZerk located through slot in tubes Constant Velocity Input Driveline Profile TubesConstant Velocity Input Driveline Joints & Shields Drivelines with internal tube grease pointWing Driveline Profile Tubes Wing Driveline Joints & ShieldsRCB6010 & RCB6015 Series RCB6010 RCB6015RCB6010 & RCB6015 Bid Specification Rotary Cutters Features BenefitsOr shock cross failing Problem Solution Oil seal leakingDriveline yoke Driveline shaftAdditional Torque Values Torque Values ChartTire Inflation Chart Tire Size InflationWarranty Overall Unit and Drivelines One year Parts and Labor GearboxCorporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA