Land Pride RCMB6015 manual Clutch Disassembly, Inspection & Assembly, Refer to -5 & Table Below

Page 26

Table of Contents

Section 4: Maintenance & Lubrication

Land Pride

6.Tighten each of the 8 spring retainer nuts on the clutch housing exactly 2 revolutions to restore clutch to original setting pressure.

7.Allow clutch to cool to ambient temperature before operating again. Clutch is now ready for use.

8.The clutch should be checked during the first hour of cutting and periodically each week. An additional set of scribe marks can be added to check for slippage. See Figure 5-5 to adjust spring length.

Clutch Disassembly, Inspection & Assembly

Refer to Figure 5-4:

If clutch run-in procedure above indicated that one or more friction disks did not slip, then the clutch must be disassembled to separate the friction disks.

Disassembly

IMPORTANT: Not all Type A clutch components are arranged as illustrated in Figure 5-4. Also some have more components than others. Be sure to keep track of order and orientation of your clutch components during disassembly.

Disassembly of clutch is simply a matter of first removing spring retainer nuts (#1), springs (#2) and bolts (#3) from the assembly. Each friction disk (#4) must then be separated from the metal surface adjacent to it.

Inspection

Inspect all parts for excessive wear and condition. Clean all parts that do not require replacement.The original friction disk thickness is 1/8" (3.2mm) and should be replaced if thickness falls below 3/64" (1.1mm). If clutches have been slipped to the point of “smoking”, the friction disks may be damaged and should be replaced. Heat build-up may also affect the yoke joints.

Refer to Figure 5-5 & Table Below:

Progressively tighten each spring retainer bolt until correct spring height “A” is reached.

24600

Type A Clutch Adjustment

Figure 5-5

Driveline

Driveline

PTO

Cat

A (inches)

No.

Location

Speed

No.

Spring Height

 

 

 

 

 

 

826-183C

Center

540

4

1.15"

(S/N 566919+)

 

 

 

 

1.12"

(S/N 566918-)

 

 

 

 

 

 

826-184C

Center

1000

4

1.09"

(S/N 566919+)

 

 

 

 

1.02"

(S/N 566918-)

 

 

 

 

 

 

826-478C

Center

540/1000

5

 

1.32"

 

 

 

 

 

826-185C

Wing

540/1000

4

1.175" (S/N 566919+)

 

 

 

 

1.14"

(S/N 566918-)

 

 

 

 

 

 

826-481C

Wing

540/1000

5

 

1.32"

 

 

 

 

 

 

Assembly

Reassemble each friction disk (#4) next to the metal plate it was separated from. Install bolts (#3) through the end plates and intermediate plates as shown. Place springs (#2) over the bolts and secure with nuts (#1).

14714

IMPORTANT: Keep track of order and orientation of

your clutch components during disassembly

Type A Clutch Disassembly

Figure 5-4

24 RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M

9/04/08

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Rotary Cutters Table of Contents Safety at All Times Practice Safe Maintenance Use Safety Lights and DevicesUse a Safety Chain Transport Machinery SafelyWear Protective Equipment Tire SafetyPrepare for Emergencies Avoid High Pressure Fluids Hazard818-240C 818-045C818-130C 818-552C Do not Operate 818-540C818-543C 818-561C 818-276C818-840C 818-830C 838-094C 818-556C818-564C 838-588C818-229C 818-230CUsing This Manual Application Owner AssistanceBefore You Start Dealer Assembly & Preparations Pre-Assembly ChecklistTractor Requirements Hydraulic Plumbing Hitch AssemblyWing Axle Assembly Swivel Clevis Hitch Hitch TypesTractor Hook-up to Swivel Clevis Hitch Bar-Tite Clevis HitchDriveline Hook-up Bar-Tite Clevis Hitch Assembly to Tractor TongueTractor Hook-up to Bar-Tite Clevis Hitch Tractor Hookup to Bar-Tite Clevis HitchPTO Driveline Shortening Hydraulic Hook-upRefer to -7on Unhooking From the Cutter Refer to -1& Figure Pre-start ChecklistCutter Set-up For Transporting Transport Bar, Locked PositionOperating Speed & Turning Angle Transporting The CutterCutter Set-up For Field Operation Refer to -1& -2onManual Wing Lift Winch Optional Manual Wing Lift WinchGeneral Operating Instructions Table of Contents Refer to -1, -2& Figure Cutting Height AdjustmentCenter and Wing Section Leveling Refer to -2 on General Maintenance InformationCutter Blade Maintenance Blade RotationType a Clutches Clutch Run-In Drivelines With Slip ClutchesLand Pride Cutter Blade Parts Clutch Disassembly, Inspection & Assembly Refer to -5 & Table BelowType B Clutch Run-In Plate Assembly Type B Clutch AssemblyType B Clutches Clutch Run-In Step Plate DisassemblyType C Clutches Clutch Run-In Refer to -8 View aPlace hub and friction discs into the housing Skid Shoe Maintenance Plate AssemblyLand Pride Skid Shoe Replacement Parts Install end half clamps if availableStorage Tractor MaintenanceWeight Box Skid Shoe Wing Skid ShoeHrs Adjustable TurnbuckleLubrication Points Axle Hub BearingDouble Swivel Clevis Hitch Main HitchWing Hinges Type of Lubrication Multi-purpose GreaseIntermediate Driveline Joints Divider BoxGearbox Type of Lubrication 80-90W EP Quantity = As requiredZerk located through slot in plastic outer tubes Conventional Driveline Profile TubesConventional Driveline Joints & Shields Drivelines with internal profile tube grease pointZerk located through slot in tubes Constant Velocity Input Driveline Profile TubesConstant Velocity Input Driveline Joints & Shields Drivelines with internal tube grease pointWing Driveline Profile Tubes Wing Driveline Joints & ShieldsRCB6010 & RCB6015 Series RCB6010 RCB6015RCB6010 & RCB6015 Bid Specification Rotary Cutters Features BenefitsOr shock cross failing Problem Solution Oil seal leakingDriveline yoke Driveline shaftAdditional Torque Values Torque Values ChartTire Inflation Chart Tire Size InflationWarranty Overall Unit and Drivelines One year Parts and Labor GearboxCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents