Land Pride RCMB6015 manual RCB6010 & RCB6015 Bid Specification Rotary Cutters, Features Benefits

Table of Contents

Section 6: Features and Benefits

RCB6010 & RCB6015 Bid Specification Rotary Cutters

Features	Benefits
250 HP Splitter box	Highest gearbox rating in its class.
210 HP wing boxes	Highest gearbox rating in its class.
Tractor HP range	50 - 250 HP
Left wing counter rotates	Better discharge of material. (Refers to RCB6015 cutters with 2 wing decks.)
Factory assembled	Arrives ready for the customer. Saves the customer set up time.
Gearbox warranty	S/N 325492+ 5 years on housing, gears and shafts, 3 years on seals & bearings.
	S/N 325491- 1 year warranty.
2 3/8” Gearbox output shaft	Large output shaft handles shock loads better.
Star profile Cat. 5 drivelines	Increased strength in driveline. Holds up to shock loads and harsh mowing conditions.
Input driveline	Cat. 5 constant velocity or conventional u-joint available.
Wing drivelines	Choice of Cat. 4 or Cat. 5 to match up to customers needs.
540 or 1000 RPM	Fits wide variety of tractors.
Dual swiveling clevis hitch	Clevis hitch bolts to tractor draw bar and swivels left to right and front to back. This allows
	cutter to float but hitch stays rigid on drawbar, which eliminates drawbar wear.
Gearbox seal protection	Gearbox bottom seal is protected for longer bearing life.
All-welded deck	Deck is 100% welded which offers additional strength and keeps moisture and dirt from
	getting trapped in tight places, which hastens rust over time.
3/16” Deck thickness	Heavy gauge material aids in resisting damage from debris hitting the underside of the deck.
1/4” Sidewall thickness	Reduces debris piercing possibilities.
10 1/2” Deck height	Handles heavy cutting, which reduces balling up of cut material under the deck.
2” to 14” Cutting Height	Cover a wide range of cutting conditions.
6” Blade overlap	Eliminates skipping during turns.
4” Cutting capacity	Enables the cutter to be used in pastures with small trees up to 4” in diameter.
High blade tip speed	(540 rpm = 15,268 fpm center & 15,000 fpm wings)
	(1000 rpm = 15,578 fpm center & 14,620 fpm wings)
	Allows clean cutting of material.
Chain guards	Front and rear double chain guards are available with cable to reduce thrown objects.
Replaceable skid shoes	Can be replaced when damaged or worn out on wings and center deck.
3/16” Round stump jumper	1” Thick plate offers superior support and protection to gearbox output shaft.
with 1” thick plate
Underside deck rings	Fully welded 1/2 ” x 3” deck rings on underside of each deck eliminates blades getting in
	deck, and offers additional overall strength to the decks.
4 Plate slip-clutch	Protects drivelines and gearboxes by slipping clutches rather than twisting the driveline
	when impacts are encountered.
Easy to Grease drivelines	Drivelines have access holes to grease the U-joints of the driveline, as well as holes to
	grease the inner profiles.
Hinged wing sections	Allow you to shape the cutter to the job. Ideal for rough ground where hillsides, ditches and
	hollows can cause uneven cutting.
1” Solid hinge rods	Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the
	hinge area itself.
Wing hydraulics	Wing hydraulics are plumbed independently to allow the user to raise one wing at a time,
	which can aid in going through narrow spaces.
Mechanical winch (optional)	Mechanical winch aids in folding the cutter in the event of hydraulic failure.
Wing transport locks	Transport wing locks securely hold wings in the folded position in case of hydraulic failure.
Slow moving vehicle sign	Standard equipment to make operating conditions safer.
Enclosed front to rear dual	Dual leveling rods enable the cutter to pull equally on the rear axle during uneven terrain
leveling rods	vs. just pulling from one side of the front hitch.
Airplane tire option	Airplane tires give better cushion while transporting the cutter. Available with heavy-duty
with optional foam sealant	foam which virtually eliminates flats.
Laminated tires option	Can’t go flat.
Replaceable wheel spindles	Wheel spindles can be replaced easily by removing two bolts vs. replacing the entire axle.
Wheels	6 or 8 Wheel option.
Spring cushioned center-axle	Protects unit from bumps and ground shock.
Walking Tandem Axles Option	Better flotation over rough terrain.
Rear axle pull ring	Aids in getting unit out of soft ground conditions.
Surpassed rugged industry	All Land Pride Cutters have been designed and tested and meet rigorous voluntary testing
standards	procedures specified by ANSI.
Paint options	Choice of red, green or tan to match popular tractor lines.

36 RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M 9/04/08