Land Pride RCMB6010, RCMB6015 Prepare for Emergencies, Wear Protective Equipment, Tire Safety

Page 5

Land Pride

Table of Contents

Important Safety Information

These are common practices that may or may not be applicable to the products described in this manual.

Prepare for Emergencies

Be prepared if a fire starts.

Keep a first aid kit and fire extinguisher handy.

Keep emergency numbers for doctor, ambulance, hospital and fire department near phone.

Wear

Protective Equipment

Wear protective clothing and equipment.

Wear clothing and equipment appropriate for the job. Avoid loose-fitting clothing.

Prolonged exposure to loud noise can cause hearing impairment or hearing loss. Wear suitable hearing protection such as earmuffs or earplugs.

Operating equipment safely requires the full attention of the operator. Avoid wearing radio headphones while operating machinery.

Avoid High

Pressure Fluids Hazard

Escaping fluid under pressure can penetrate the skin, causing serious injury.

Avoid the hazard by relieving pressure before disconnecting hydraulic lines.

Use a piece of paper or cardboard, NOT BODY PARTS, to check for suspected leaks.

Wear protective gloves and safety glasses or goggles when working with hydraulic systems.

If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be treated within a few hours or gangrene may result.

911

Tire Safety

Tire changing can be dangerous and should be preformed by trained personnel using the correct tools and equipment.

When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly. Use a safety cage if available.

When removing and installing wheels, use wheel handling equipment adequate for the weight involved.

Keep Riders

Off Machinery

Riders obstruct the operator’s view, they could be struck by foreign objects or thrown from the machine.

Never allow children to operate equipment.

9/04/08

RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M

3

Image 5
Contents Rotary Cutters Table of Contents Safety at All Times Use a Safety Chain Use Safety Lights and DevicesPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Tire SafetyWear Protective Equipment Avoid High Pressure Fluids Hazard818-240C 818-045C818-130C 818-552C Do not Operate 818-540C818-543C 818-561C 818-276C818-840C 818-830C 818-564C 818-556C838-094C 838-588C818-230C 818-229CApplication Owner Assistance Using This ManualBefore You Start Dealer Assembly & Preparations Pre-Assembly ChecklistTractor Requirements Hydraulic Plumbing Hitch AssemblyWing Axle Assembly Tractor Hook-up to Swivel Clevis Hitch Hitch TypesSwivel Clevis Hitch Bar-Tite Clevis HitchTractor Hook-up to Bar-Tite Clevis Hitch Bar-Tite Clevis Hitch Assembly to Tractor TongueDriveline Hook-up Tractor Hookup to Bar-Tite Clevis HitchPTO Driveline Shortening Hydraulic Hook-upRefer to -7on Unhooking From the Cutter Cutter Set-up For Transporting Pre-start ChecklistRefer to -1& Figure Transport Bar, Locked PositionCutter Set-up For Field Operation Transporting The CutterOperating Speed & Turning Angle Refer to -1& -2onManual Wing Lift Winch Optional Manual Wing Lift WinchGeneral Operating Instructions Table of Contents Refer to -1, -2& Figure Cutting Height AdjustmentCenter and Wing Section Leveling Cutter Blade Maintenance General Maintenance InformationRefer to -2 on Blade RotationType a Clutches Clutch Run-In Drivelines With Slip ClutchesLand Pride Cutter Blade Parts Refer to -5 & Table Below Clutch Disassembly, Inspection & AssemblyType B Clutch Run-In Plate Assembly Type B Clutch AssemblyType B Clutches Clutch Run-In Type C Clutches Clutch Run-In Plate DisassemblyStep Refer to -8 View aLand Pride Skid Shoe Replacement Parts Skid Shoe Maintenance Plate AssemblyPlace hub and friction discs into the housing Install end half clamps if availableWeight Box Skid Shoe Tractor MaintenanceStorage Wing Skid ShoeLubrication Points Adjustable TurnbuckleHrs Axle Hub BearingWing Hinges Main HitchDouble Swivel Clevis Hitch Type of Lubrication Multi-purpose GreaseGearbox Divider BoxIntermediate Driveline Joints Type of Lubrication 80-90W EP Quantity = As requiredConventional Driveline Joints & Shields Conventional Driveline Profile TubesZerk located through slot in plastic outer tubes Drivelines with internal profile tube grease pointConstant Velocity Input Driveline Joints & Shields Constant Velocity Input Driveline Profile TubesZerk located through slot in tubes Drivelines with internal tube grease pointWing Driveline Joints & Shields Wing Driveline Profile TubesRCB6010 RCB6015 RCB6010 & RCB6015 SeriesFeatures Benefits RCB6010 & RCB6015 Bid Specification Rotary CuttersDriveline yoke Problem Solution Oil seal leakingOr shock cross failing Driveline shaftTire Inflation Chart Torque Values ChartAdditional Torque Values Tire Size InflationOverall Unit and Drivelines One year Parts and Labor Gearbox WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA