Land Pride RCMB6015, RCMB6010 manual Tractor Hook-up to Bar-Tite Clevis Hitch, Driveline Hook-up

Page 16

Table of Contents

Section 1: Preparation and Set-up

Land Pride

Tractor Hook-up to

Bar-Tite Clevis Hitch

Refer to Figure 1-6:

1.Attach Bar-Tite clevis hitch to tractor drawbar:

a.Insert 1" x 5" hex bolt (#7) through hitch top plate (#2), hitch weldment with bushing (#4), hitch base weldment (#5) and tractor drawbar (#13) as shown. Secure with 1" lock nut (#9). Tighten lock nut snugly to remove all play and then back nut one-quarter turn. Do Not torque 1" lock nut.

b.Insert two 3/4" x 5 1/2" gr5 hex bolts (#8) through, 3/4" flat washers (#11), hitch top plate (#2), hitch base weldment (#5) and formed hitch support (#3) as shown. Secure with 3/4" lock nuts (#10).

c.Tighten 3/4" lock nuts to the correct torque. See Torque Values Chart on page 38.

d.Remove 1" x 6 1/2" gr5 hex bolt (#6) and 1" lock nut (#12) from hitch weldment (#4).

22265

Bar-Tite Clevis Hitch Assembly to Tractor Tongue

Figure 1-6

!DANGER!

Crushing Hazard between tractor and implement. Do not allow anyone to stand between the tractor and implement while backing-up to an implement. Never operate the hydraulic

3-point lift controls while someone is directly behind the tractor.

Refer to Figure 1-7:

IMPORTANT: Jack attachment pin (#8) must be fully inserted and secured before working on or around a cutter that is not hooked to the tractor drawbar.

2.Make certain the parking jack (#3) is properly attached to the cutter and secured with attachment pin (#8).

3.Back tractor within close proximity of cutter hitch.

4.Raise or lower the parking jack (#3) to align hitch (#10) with bolt hole in swivel clevis (#9).

5.Back tractor up to cutter swivel hitch (#9) until hole in hitch weldment with bushing (#10) aligns with holes in swivel clevis (#9).

6.Insert 1" x 6 1/2" gr5 hex bolt (#1) through the cutter swivel hitch (#9) and hitch weldment (#10). Secure hex bolt with lock nut (#2). Tighten lock nut snugly to remove all play. Do Not torque 1" lock nut.

7.Lower jack stand (#3) until hitch weight is removed. Remove jack stand from hitch and store on left hand deck wing storage base or weight box. Prevent water and freeze damage by storing it so that the foot is level or lower than the head, especially when the wing is folded up.

8.Attach hitch safety chain (#4) to the tractor. Adjust chain length to remove all slack except what is necessary to permit turning. Lock chain hook securely to the safety chain.

22262

Tractor Hookup to Bar-Tite Clevis Hitch

Figure 1-7

Driveline Hook-up

!CAUTION!

Tractor PTO shields and guards must be in place at all times during operation!

The cutter driveline is coupled to the tractor and implement shafts with a pull collar coupler and retaining bolt.

14 RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M

9/04/08

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Rotary Cutters Table of Contents Safety at All Times Use Safety Lights and Devices Use a Safety ChainPractice Safe Maintenance Transport Machinery SafelyTire Safety Prepare for EmergenciesWear Protective Equipment Avoid High Pressure Fluids Hazard818-130C 818-045C818-240C 818-552C 818-543C 818-540CDo not Operate 818-840C 818-830C 818-276C818-561C 818-556C 818-564C838-094C 838-588C818-229C 818-230CUsing This Manual Application Owner AssistanceTractor Requirements Dealer Assembly & Preparations Pre-Assembly ChecklistBefore You Start Wing Axle Assembly Hitch AssemblyHydraulic Plumbing Hitch Types Tractor Hook-up to Swivel Clevis HitchSwivel Clevis Hitch Bar-Tite Clevis HitchBar-Tite Clevis Hitch Assembly to Tractor Tongue Tractor Hook-up to Bar-Tite Clevis HitchDriveline Hook-up Tractor Hookup to Bar-Tite Clevis HitchRefer to -7on Hydraulic Hook-upPTO Driveline Shortening Unhooking From the Cutter Pre-start Checklist Cutter Set-up For TransportingRefer to -1& Figure Transport Bar, Locked PositionTransporting The Cutter Cutter Set-up For Field OperationOperating Speed & Turning Angle Refer to -1& -2onGeneral Operating Instructions Optional Manual Wing Lift WinchManual Wing Lift Winch Table of Contents Center and Wing Section Leveling Cutting Height AdjustmentRefer to -1, -2& Figure General Maintenance Information Cutter Blade MaintenanceRefer to -2 on Blade RotationLand Pride Cutter Blade Parts Drivelines With Slip ClutchesType a Clutches Clutch Run-In Clutch Disassembly, Inspection & Assembly Refer to -5 & Table BelowType B Clutches Clutch Run-In Plate Assembly Type B Clutch AssemblyType B Clutch Run-In Plate Disassembly Type C Clutches Clutch Run-InStep Refer to -8 View aSkid Shoe Maintenance Plate Assembly Land Pride Skid Shoe Replacement PartsPlace hub and friction discs into the housing Install end half clamps if availableTractor Maintenance Weight Box Skid ShoeStorage Wing Skid ShoeAdjustable Turnbuckle Lubrication PointsHrs Axle Hub BearingMain Hitch Wing HingesDouble Swivel Clevis Hitch Type of Lubrication Multi-purpose GreaseDivider Box GearboxIntermediate Driveline Joints Type of Lubrication 80-90W EP Quantity = As requiredConventional Driveline Profile Tubes Conventional Driveline Joints & ShieldsZerk located through slot in plastic outer tubes Drivelines with internal profile tube grease pointConstant Velocity Input Driveline Profile Tubes Constant Velocity Input Driveline Joints & ShieldsZerk located through slot in tubes Drivelines with internal tube grease pointWing Driveline Profile Tubes Wing Driveline Joints & ShieldsRCB6010 & RCB6015 Series RCB6010 RCB6015RCB6010 & RCB6015 Bid Specification Rotary Cutters Features BenefitsProblem Solution Oil seal leaking Driveline yokeOr shock cross failing Driveline shaftTorque Values Chart Tire Inflation ChartAdditional Torque Values Tire Size InflationWarranty Overall Unit and Drivelines One year Parts and Labor GearboxCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents