Land Pride RCMB6015, RCMB6010 manual Unhooking From the Cutter

Page 18

Table of Contents

Section 1: Preparation and Set-up

Unhooking From the Cutter

1.Park cutter on a level solid hard surface. Place tractor gear selector in park and set park brake.

2.Refer to “Transporting The Cutter”, Figure 2-1 & Figure 2-2on page 18. Raise wings up in the transport position and place transport lock bars in the locked position. Make sure transport bars are secured in place with lock pins (#2) and hair pins (#1).

3.Remove stroke control spacers from the center hydraulic cylinder and lower cutter until front skids are resting on the ground. Replace stroke control spacers as needed to support wheels at this position.

4.With tractor gear selector in park and park brake set, shut tractor engine off, and remove switch key. Move cylinder lift levers back and forth to release hydraulic line pressure.

5.Refer to “Hitch Assembly Illustration” (Figure 1-2) on page 12. Remove the parking jack (#3) from the left hand wing deck or weight box and install to cutter hitch. Secure the parking jack in place with attached jack pin (#4).

6.Adjust the parking jack as needed to remove the hitch pin.

7.Remove hitch pin and unhook hydraulic hoses from tractor. Store hose ends on cutter deck.

8.Lower the parking jack to rest cutter on its front skids.

Land Pride

16 RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M

9/04/08

Image 18

Contents Rotary Cutters Table of Contents Safety at All Times Practice Safe Maintenance Use Safety Lights and DevicesUse a Safety Chain Transport Machinery SafelyWear Protective Equipment Tire SafetyPrepare for Emergencies Avoid High Pressure Fluids Hazard818-045C 818-130C818-240C 818-552C 818-540C 818-543CDo not Operate 818-276C 818-840C 818-830C818-561C 838-094C 818-556C818-564C 838-588C818-229C 818-230CUsing This Manual Application Owner AssistanceDealer Assembly & Preparations Pre-Assembly Checklist Tractor RequirementsBefore You Start Hitch Assembly Wing Axle AssemblyHydraulic Plumbing Swivel Clevis Hitch Hitch TypesTractor Hook-up to Swivel Clevis Hitch Bar-Tite Clevis HitchDriveline Hook-up Bar-Tite Clevis Hitch Assembly to Tractor TongueTractor Hook-up to Bar-Tite Clevis Hitch Tractor Hookup to Bar-Tite Clevis HitchHydraulic Hook-up Refer to -7onPTO Driveline Shortening Unhooking From the Cutter Refer to -1& Figure Pre-start ChecklistCutter Set-up For Transporting Transport Bar, Locked PositionOperating Speed & Turning Angle Transporting The CutterCutter Set-up For Field Operation Refer to -1& -2onOptional Manual Wing Lift Winch General Operating InstructionsManual Wing Lift Winch Table of Contents Cutting Height Adjustment Center and Wing Section LevelingRefer to -1, -2& Figure Refer to -2 on General Maintenance InformationCutter Blade Maintenance Blade RotationDrivelines With Slip Clutches Land Pride Cutter Blade PartsType a Clutches Clutch Run-In Clutch Disassembly, Inspection & Assembly Refer to -5 & Table BelowPlate Assembly Type B Clutch Assembly Type B Clutches Clutch Run-InType B Clutch Run-In Step Plate DisassemblyType C Clutches Clutch Run-In Refer to -8 View aPlace hub and friction discs into the housing Skid Shoe Maintenance Plate AssemblyLand Pride Skid Shoe Replacement Parts Install end half clamps if availableStorage Tractor MaintenanceWeight Box Skid Shoe Wing Skid ShoeHrs Adjustable TurnbuckleLubrication Points Axle Hub BearingDouble Swivel Clevis Hitch Main HitchWing Hinges Type of Lubrication Multi-purpose GreaseIntermediate Driveline Joints Divider BoxGearbox Type of Lubrication 80-90W EP Quantity = As requiredZerk located through slot in plastic outer tubes Conventional Driveline Profile TubesConventional Driveline Joints & Shields Drivelines with internal profile tube grease pointZerk located through slot in tubes Constant Velocity Input Driveline Profile TubesConstant Velocity Input Driveline Joints & Shields Drivelines with internal tube grease pointWing Driveline Profile Tubes Wing Driveline Joints & ShieldsRCB6010 & RCB6015 Series RCB6010 RCB6015RCB6010 & RCB6015 Bid Specification Rotary Cutters Features BenefitsOr shock cross failing Problem Solution Oil seal leakingDriveline yoke Driveline shaftAdditional Torque Values Torque Values ChartTire Inflation Chart Tire Size InflationWarranty Overall Unit and Drivelines One year Parts and Labor GearboxCorporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA