Land Pride RCMB6010 Problem Solution Oil seal leaking, Driveline yoke, Or shock cross failing

Page 39

Land Pride

Table of Contents

Section 7: Troubleshooting

	Problem	Solution

	Oil seal leaking	Drain to level ﬁll hole

		Replace seals

		Clean off wrapped material and check seal areas daily

	Driveline yoke	Avoid hitting solid objects
	or shock cross failing
	or shock cross failing	Lubricate every 8 hours
		Lubricate every 8 hours

	Slip Clutches slip even with a light load	Replace clutch plates

		Remove foreign object

	Bent Driveline shaft (Note: Driveline shaft	Reduce lift height in transport position
	should be repaired or replaced if bent)
	should be repaired or replaced if bent)	Reposition drawbar
		Reposition drawbar

		Shorten Power Take Off shaft

	Driveline shaft	Avoid hitting solid objects
	telescoping tube failing

	Driveline shaft	Lubricate every 20 hours of operation
	telescoping tube wearing

	Blades wearing excessively	Raise cutting height

	Blades coming loose	Tighten blade hardware, refer to “Cutter Blade Maintenance” starting on page 22.

	Blades breaking	Avoid solid objects

	Loose blade carrier	Replace gearbox bearings and / or shaft

		Tighten shaft nut to speciﬁed torque

	Blade carrier bent	Avoid hitting solid objects

	Excessive side skid wear	Adjust cutter height

		Raise cutting height

	Excessive vibration	Replace Power Take Off or distribution shaft

		Replace blade carrier

		Replace blade

		Inspect and unlock blades

		Disassemble and inspect for incorrectly located needles or damaged bearing cap

		Replace each pair of blades on affected carrier

	Wing cylinder movement too slow	Remove elbow ﬁtting and remove oriﬁce

9/04/08

RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M

37

Image 39

Contents Rotary Cutters Table of Contents Safety at All Times Transport Machinery Safely Use Safety Lights and DevicesUse a Safety Chain Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Tire SafetyPrepare for Emergencies Wear Protective Equipment818-045C 818-130C818-240C 818-552C 818-540C 818-543CDo not Operate 818-276C 818-840C 818-830C818-561C 838-588C 818-556C818-564C 838-094C818-230C 818-229CApplication Owner Assistance Using This ManualDealer Assembly & Preparations Pre-Assembly Checklist Tractor RequirementsBefore You Start Hitch Assembly Wing Axle AssemblyHydraulic Plumbing Bar-Tite Clevis Hitch Hitch TypesTractor Hook-up to Swivel Clevis Hitch Swivel Clevis HitchTractor Hookup to Bar-Tite Clevis Hitch Bar-Tite Clevis Hitch Assembly to Tractor TongueTractor Hook-up to Bar-Tite Clevis Hitch Driveline Hook-upHydraulic Hook-up Refer to -7onPTO Driveline Shortening Unhooking From the Cutter Transport Bar, Locked Position Pre-start ChecklistCutter Set-up For Transporting Refer to -1& FigureRefer to -1& -2on Transporting The CutterCutter Set-up For Field Operation Operating Speed & Turning AngleOptional Manual Wing Lift Winch General Operating InstructionsManual Wing Lift Winch Table of Contents Cutting Height Adjustment Center and Wing Section LevelingRefer to -1, -2& Figure Blade Rotation General Maintenance InformationCutter Blade Maintenance Refer to -2 onDrivelines With Slip Clutches Land Pride Cutter Blade PartsType a Clutches Clutch Run-In Refer to -5 & Table Below Clutch Disassembly, Inspection & AssemblyPlate Assembly Type B Clutch Assembly Type B Clutches Clutch Run-InType B Clutch Run-In Refer to -8 View a Plate DisassemblyType C Clutches Clutch Run-In StepInstall end half clamps if available Skid Shoe Maintenance Plate AssemblyLand Pride Skid Shoe Replacement Parts Place hub and friction discs into the housingWing Skid Shoe Tractor MaintenanceWeight Box Skid Shoe StorageAxle Hub Bearing Adjustable TurnbuckleLubrication Points HrsType of Lubrication Multi-purpose Grease Main HitchWing Hinges Double Swivel Clevis HitchType of Lubrication 80-90W EP Quantity = As required Divider BoxGearbox Intermediate Driveline JointsDrivelines with internal profile tube grease point Conventional Driveline Profile TubesConventional Driveline Joints & Shields Zerk located through slot in plastic outer tubesDrivelines with internal tube grease point Constant Velocity Input Driveline Profile TubesConstant Velocity Input Driveline Joints & Shields Zerk located through slot in tubesWing Driveline Joints & Shields Wing Driveline Profile TubesRCB6010 RCB6015 RCB6010 & RCB6015 SeriesFeatures Benefits RCB6010 & RCB6015 Bid Specification Rotary CuttersDriveline shaft Problem Solution Oil seal leakingDriveline yoke Or shock cross failingTire Size Inflation Torque Values ChartTire Inflation Chart Additional Torque ValuesOverall Unit and Drivelines One year Parts and Labor Gearbox WarrantyCorporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA