Land Pride RCMB6010 Hitch Types, Tractor Hook-up to Swivel Clevis Hitch, Bar-Tite Clevis Hitch

Page 15

Land Pride

Table of Contents

Section 1: Preparation and Set-up

Hitch Types

Refer to Figure 1-4:

The cutter will have one of two hitch types shown below.

22268

Hitch Types

Figure 1-4

Swivel Clevis Hitch

The swivel clevis hitch allows the cutter to pivot about the tractor drawbar freely in two directions. It is designed for cutting hillsides, reducing the twisting torque on the cutter hitch and tractor drawbar. Hitch swivel is greaseable.

Bar-Tite Clevis Hitch

The Bar-Tite clevis hitch functions the same as the swivel clevis hitch except it is constructed of case hardened steel and has a bushing in the tongue to extend hitch life. Bushing and hitch swivel are greaseable.

Tractor Hook-up to Swivel Clevis Hitch

!DANGER!

Crushing Hazard between tractor and implement. Do not allow anyone to stand between the tractor and implement while backing-up to an implement. Never operate the hydraulic

3-point lift controls while someone is directly behind the tractor.

Refer to Figure 1-5:

IMPORTANT: Jack attachment pin (#8) must be fully inserted and secured before working on or around a cutter that is not hooked to the tractor drawbar.

1.Make certain the parking jack (#3) is properly at- tached to the cutter hitch and secured with attachment pin (#8).

2.Back tractor within close proximity of cutter clevis (#11).

3.Raise or lower the parking jack (#3) to align clevis (#11) with the tractor drawbar. Drawbar should fit between lower and upper plates of clevis.

4.Back tractor up to cutter hitch until holes in the drawbar and clevis (#11) are aligned.

5.Insert 1" flat washers (#9) equally above and below tractor drawbar until both spaces between drawbar and clevis plates are filled.

6.Insert 1" x 5" gr5 hex bolt (#1) through top of clevis (#11), 1" washers (#9), drawbar, remaining 1" washers (#9) and out through bottom of clevis (#11). Secure hex bolt with nut (#2). Tighten nut snugly to remove all play and then back nut one-quarter turn. Tighten jamb nut (#10) against nut (#2).

7.Lower jack stand (#3) until hitch weight is removed. Remove jack stand from hitch and store on left hand deck wing storage base or weight box. Prevent water and freeze damage by storing it so that the foot is level or lower than the head, especially when the wing is folded up.

8.Attach hitch safety chain (#4) to the tractor. Adjust chain length to remove all slack except what is necessary to permit turning. Lock chain hook securely to the safety chain.

22271

Tractor Hookup to Double Swivel Clevis Clamp Hitch

Figure 1-5

9/04/08

RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters 318-263M

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Rotary Cutters Table of Contents Safety at All Times Transport Machinery Safely Use Safety Lights and DevicesUse a Safety Chain Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Tire SafetyPrepare for Emergencies Wear Protective Equipment818-045C 818-130C818-240C 818-552C 818-540C 818-543CDo not Operate 818-276C 818-840C 818-830C818-561C 838-588C 818-556C818-564C 838-094C818-230C 818-229CApplication Owner Assistance Using This ManualDealer Assembly & Preparations Pre-Assembly Checklist Tractor RequirementsBefore You Start Hitch Assembly Wing Axle AssemblyHydraulic Plumbing Bar-Tite Clevis Hitch Hitch TypesTractor Hook-up to Swivel Clevis Hitch Swivel Clevis HitchTractor Hookup to Bar-Tite Clevis Hitch Bar-Tite Clevis Hitch Assembly to Tractor TongueTractor Hook-up to Bar-Tite Clevis Hitch Driveline Hook-upHydraulic Hook-up Refer to -7onPTO Driveline Shortening Unhooking From the Cutter Transport Bar, Locked Position Pre-start ChecklistCutter Set-up For Transporting Refer to -1& FigureRefer to -1& -2on Transporting The CutterCutter Set-up For Field Operation Operating Speed & Turning AngleOptional Manual Wing Lift Winch General Operating InstructionsManual Wing Lift Winch Table of Contents Cutting Height Adjustment Center and Wing Section LevelingRefer to -1, -2& Figure Blade Rotation General Maintenance InformationCutter Blade Maintenance Refer to -2 onDrivelines With Slip Clutches Land Pride Cutter Blade PartsType a Clutches Clutch Run-In Refer to -5 & Table Below Clutch Disassembly, Inspection & AssemblyPlate Assembly Type B Clutch Assembly Type B Clutches Clutch Run-InType B Clutch Run-In Refer to -8 View a Plate DisassemblyType C Clutches Clutch Run-In StepInstall end half clamps if available Skid Shoe Maintenance Plate AssemblyLand Pride Skid Shoe Replacement Parts Place hub and friction discs into the housingWing Skid Shoe Tractor MaintenanceWeight Box Skid Shoe StorageAxle Hub Bearing Adjustable TurnbuckleLubrication Points HrsType of Lubrication Multi-purpose Grease Main HitchWing Hinges Double Swivel Clevis HitchType of Lubrication 80-90W EP Quantity = As required Divider BoxGearbox Intermediate Driveline JointsDrivelines with internal profile tube grease point Conventional Driveline Profile TubesConventional Driveline Joints & Shields Zerk located through slot in plastic outer tubesDrivelines with internal tube grease point Constant Velocity Input Driveline Profile TubesConstant Velocity Input Driveline Joints & Shields Zerk located through slot in tubesWing Driveline Joints & Shields Wing Driveline Profile TubesRCB6010 RCB6015 RCB6010 & RCB6015 SeriesFeatures Benefits RCB6010 & RCB6015 Bid Specification Rotary CuttersDriveline shaft Problem Solution Oil seal leakingDriveline yoke Or shock cross failingTire Size Inflation Torque Values ChartTire Inflation Chart Additional Torque ValuesOverall Unit and Drivelines One year Parts and Labor Gearbox WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents