Land Pride RCMB6010, RCMB6015 manual Divider Box, Gearbox, Intermediate Driveline Joints

Page 33

Land Pride

Table of Contents

Section 4: Maintenance & Lubrication

Oil Fill & Vent Plug

Oil Level Plug

	24852
	Oil Fill Plug
	Oil Level Plug
23603	Oil Drain Plug

8

Hrs

Divider Box

Type of Lubrication: 80-90W EP

Quantity = As required

NOTE: Do not overfill! Cutter should be level when checking oil. If, for any reason, all oil has been removed from gearbox, refill to level plug and allow air to bleed up from lower cavity, then recheck.

23582

IMPORTANT: Your cutter is shipped with the gearbox vent plug with dipstick packaged in the Operator’s Manual bag and should have been installed in the gearbox by your Land Pride dealer. Please see your Land Pride dealer if the vent plug with dipstick was not included.

8

Hrs

Gearbox

IMPORTANT: Do not overfill! Level cutter and wait for gearbox oil to cool before checking. An unlevel cutter or a gearbox with hot oil will not show correct oil level on the dipstick.

Make sure wings are down. Unscrew top vent plug in gearbox to remove dipstick. Wipe excess oil from dipstick and screw it back into the plug hole. Remove dipstick again and check oil level mark on dipstick. If low, fill through top plug hole in gearbox with EP90 oil until oil reaches full mark on dipstick. Reinstall vent plug with dipstick and tighten.

Take your gearbox to a Land Pride dealer if it requires service.

Type of Lubrication: EP90 Oil

Quantity = Fill until oil reaches full mark on dipstick.

		8
		Hrs
	Intermediate Driveline Joints
	Type of Lubrication: Multi-purpose Grease
	23563
9/04/08	RCB6010 & RCB6015 (540 RPM) and RCMB6010 & RCMB6015 (1000 RPM) Rotary Cutters	318-263M	31

Image 33

Contents Rotary Cutters Table of Contents Safety at All Times Use a Safety Chain Use Safety Lights and DevicesPractice Safe Maintenance Transport Machinery SafelyPrepare for Emergencies Tire SafetyWear Protective Equipment Avoid High Pressure Fluids Hazard818-045C 818-130C818-240C 818-552C 818-540C 818-543CDo not Operate 818-276C 818-840C 818-830C818-561C 818-564C 818-556C838-094C 838-588C818-230C 818-229CApplication Owner Assistance Using This ManualDealer Assembly & Preparations Pre-Assembly Checklist Tractor RequirementsBefore You Start Hitch Assembly Wing Axle AssemblyHydraulic Plumbing Tractor Hook-up to Swivel Clevis Hitch Hitch TypesSwivel Clevis Hitch Bar-Tite Clevis HitchTractor Hook-up to Bar-Tite Clevis Hitch Bar-Tite Clevis Hitch Assembly to Tractor TongueDriveline Hook-up Tractor Hookup to Bar-Tite Clevis HitchHydraulic Hook-up Refer to -7onPTO Driveline Shortening Unhooking From the Cutter Cutter Set-up For Transporting Pre-start ChecklistRefer to -1& Figure Transport Bar, Locked PositionCutter Set-up For Field Operation Transporting The CutterOperating Speed & Turning Angle Refer to -1& -2onOptional Manual Wing Lift Winch General Operating InstructionsManual Wing Lift Winch Table of Contents Cutting Height Adjustment Center and Wing Section LevelingRefer to -1, -2& Figure Cutter Blade Maintenance General Maintenance InformationRefer to -2 on Blade RotationDrivelines With Slip Clutches Land Pride Cutter Blade PartsType a Clutches Clutch Run-In Refer to -5 & Table Below Clutch Disassembly, Inspection & AssemblyPlate Assembly Type B Clutch Assembly Type B Clutches Clutch Run-InType B Clutch Run-In Type C Clutches Clutch Run-In Plate DisassemblyStep Refer to -8 View aLand Pride Skid Shoe Replacement Parts Skid Shoe Maintenance Plate AssemblyPlace hub and friction discs into the housing Install end half clamps if availableWeight Box Skid Shoe Tractor MaintenanceStorage Wing Skid ShoeLubrication Points Adjustable TurnbuckleHrs Axle Hub BearingWing Hinges Main HitchDouble Swivel Clevis Hitch Type of Lubrication Multi-purpose GreaseGearbox Divider BoxIntermediate Driveline Joints Type of Lubrication 80-90W EP Quantity = As requiredConventional Driveline Joints & Shields Conventional Driveline Profile TubesZerk located through slot in plastic outer tubes Drivelines with internal profile tube grease pointConstant Velocity Input Driveline Joints & Shields Constant Velocity Input Driveline Profile TubesZerk located through slot in tubes Drivelines with internal tube grease pointWing Driveline Joints & Shields Wing Driveline Profile TubesRCB6010 RCB6015 RCB6010 & RCB6015 SeriesFeatures Benefits RCB6010 & RCB6015 Bid Specification Rotary CuttersDriveline yoke Problem Solution Oil seal leakingOr shock cross failing Driveline shaftTire Inflation Chart Torque Values ChartAdditional Torque Values Tire Size InflationOverall Unit and Drivelines One year Parts and Labor Gearbox WarrantyCorporate Ofﬁce P.O. Box Salina, Kansas 67402-5060 USA