Honeywell hw400, L, HW3000 service manual Consumer Maintenance Schedule

Page 26

CONSUMER MAINTENANCE SCHEDULE

FUEL RECOMMENDATIONS

Before each use, check the fuel tank gage. If the fuel level is low, refill the tank with recommended fuel. NEVER OVERFILL.

DANGER

Fuel and fuel vapors are extremely flammable and explosive under certain conditions.

•Refuel generator only outdoors, in a well-ventilated area.

•NEVER fill fuel tank while engine is running. Turn gen- erator OFF and allow to cool before filling with fuel.

•NEVER smoke or allow flames or sparks near genera- tor or where gasoline is stored.

•NEVER overfill fuel tank (no fuel should be in filler neck). After refueling, tighten the fuel cap securely.

•Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite. If any fuel is spilled, the area must be dry before starting the engine.

•Avoid repeated or prolonged contact with skin or breathing of vapor.

General Fuel Information

Check the fuel gage located on the top of the generator near the fuel tank and refill the tank if fuel level is low. Refuel carefully to avoid spilling fuel. Do not fill above the shoulder of fuel strainer. Use unleaded gasoline with a pump octane rating of 87 or higher.

NEVER use stale or contaminated gasoline. Avoid getting dirt or water in the fuel tank. Always keep the fuel strainer in place while refueling.

Oxygenated Fuels

At certain times of the year, some U.S. locations may have only oxygenated fuel available. Oxygenated fuel is blended with alcohol or ether additives to increase octane quality, enhance combustion, and reduce exhaust emis- sions.

Some areas of the United States use oxygenated fuels to help meet clean air standards.

Before using an oxygenated fuel, ensure pump octane rat- ing is 87 or higher.

Some states (and provinces in Canada) require this infor- mation to be posted on the fuel pump. If you notice unde- sirable operating symptoms, switch to a conventional unleaded gasoline.

NOTICE

Oxygenated fuels can damage paint and plastic. Be careful not to spill fuel when filling fuel tank. Damage caused by spilled fuel is not covered under warranty.

TABLE 7-2.Oxygenated Fuel Types

 

Gasoline containing more

 

than 10% ethanol by volume

Ethanol

may cause starting or perfor-

mance problems. Gasoline

(ethyl or grain alcohol)

containing ethanol may be

 

 

marketed under the name

 

"Gasohol".

 

 

 

Gasoline containing metha-

 

nol must contain co-solvents

 

and corrosion inhibitors to

Methanol

protect fuel system. Gasoline

containing more than 5%

(methyl or wood

methanol by volume may

alcohol)

cause starting and/or perfor-

 

 

mance problems and may

 

damage metal, rubber and

 

plastic parts of fuel system.

 

 

MTBE

Gasoline containing up to

(methyl tertiary butyl

15% MTBE by volume can

ether)

be used.

 

 

NOTICE

To avoid damage to the engine, NEVER use stale or contam- inated gasoline or oil/gasoline mixture. Avoid getting dirt or water in the fuel tank.

Use fresh gasoline with a pump octane rating of 87 or higher.

NOTICE

Running the engine with persistent spark knock or pinging can cause engine damage. Warranty does not cover parts damaged by misuse.

7-2

www.honeywellgenerators.com

Honeywell Portable Electrical Generator Service Manual

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Read and Save These Instructions Page Contents This page Intentionally Left Blank Ards Important Safety InstructionsSafety Messages Safety Messages Electric Shock HazardsNorthshore Power Systems Consumer Limited Warranty WarrantiesWarranty Statement WarrantiesQuestions Northshore Power Systems Replacement Parts Limited Warranty Specifications and Wiring Diagrams SpecificationsBolt and Fastener Torque Information Bolt and Fastener Torque InformationWiring Diagrams Wiring DiagramsHW4000 & HW4000L HW5500 & HW5500L HW5500E & HW5500EL HW6200 & HW6200L HW7000E, HW7000EL, HW7500E, & HW7500EL Components This page Intentionally Left Blank Transporting Generator Preparing for ServiceRequired Tools This page Intentionally Left Blank Service Repair Time Analysis & Flat Rate Schedule OperationService Repair Time Analysis MiscMaintenance Consumer Maintenance ScheduleConsumer Maintenance Schedule Ter more frequently AIR Filter MaintenanceAIR Filter Maintenance Squeeze out excess oil Coat the air filter with clean engine oilRemove foam air filters Spark Plug Service Cleaning Fuel Sediment CUPCleaning Fuel Sediment CUP Cleaning Spark Arrestor Screen Cleaning Spark Arrestor ScreenValve Lash Governor AdjustmentValve Lash Xtreme Battery ServiceBattery Service Yuasa 12N14-3ATroubleshooting Electrical Diagnostics HW3000/L Models Electrical Diagnostics HW3000/L ModelsAlternator Refer to Illustrations on Brush Assembly Electrical Diagnostics ALL Models Except HW3000/L Electrical Diagnostics ALL Models Except HW3000/L7000 Refer to Illustrations on AVR TAP Engine Diagnostics ALL Models Engine Diagnostics ALL ModelsNm 3 lb. ft Service and DisassemblyControl Panel Engine and Alternator See WHEEL, LEG, & Handle ASSEMBLY,Engine and Alternator Cylinder Head Bolts 48 Nm 35 lb. ftAlso known as Automatic Voltage Regulator or AVR AlternatorAlternator Fuel Tank System Fuel Tank SystemNm 1.5 lb. ft Evaporative Emissions Control SystemEvaporative Emissions Control System Muffler MufflerCarburetor CarburetorStarter Solenoid Terminal Nut 6 Nm 4 lb. ft Starting SystemStarting System Check for continuityRecoil Starter Install with recoil starter handle position as shownRecoil Starter Check for wear or damageFAN Cover Remove and install with the recoil starter assemblyInstall with the recoil starter handle position as shown FAN CoverWHEEL, LEG, & Handle Assembly WHEEL, LEG, & Handle Assembly HW3000/L ModelsWHEEL, LEG, & Handle Assembly ALL Models Except HW3000/L 25 Nm 18 lb. ftIndex Northshore Power Systems, LLC

hw400, HW3000, L specifications

Honeywell is renowned for its innovative solutions in various domains, including manufacturing, aerospace, and building technologies. Among its many offerings, the Honeywell L, HW3000, and HW400 series stand out for their advanced features, technologies, and characteristics, tailored to meet the evolving demands of industries worldwide.

The Honeywell L Series is recognized for its versatility and reliability in process control applications. Designed to accommodate a range of industrial needs, these controllers provide enhanced flexibility with modifiable configurations that suit diverse operating conditions. With advanced user interfaces, intuitive programming options, and robust execution capabilities, they optimize performance while simplifying system maintenance.

The HW3000 series takes innovation a notch higher, featuring cutting-edge process automation technologies. It leverages advanced algorithms and communication protocols, facilitating seamless integration with existing systems and enhancing overall efficiency. This series is designed for high-performance operations, offering real-time data monitoring and control. The HW3000's modular architecture allows for easy upgrades and scalability, making it ideal for businesses planning for growth.

On the other hand, the Honeywell HW400 series is engineered for precision and reliability. It is equipped with state-of-the-art sensors and control mechanisms that ensure optimal performance in demanding environments. The HW400 model emphasizes sustainability, incorporating energy-efficient technologies that align with global initiatives for greener operations. Users benefit from advanced diagnostics and predictive maintenance capabilities, which minimize downtime and enhance productivity.

All three series—L, HW3000, and HW400—share a commitment to security and data integrity. Honeywell incorporates cybersecurity measures to protect sensitive information and facilitate secure communications. Moreover, they embrace a user-friendly design philosophy, ensuring that operators can easily interface with the systems, regardless of their technical background.

In summary, Honeywell's L, HW3000, and HW400 series highlight the company’s dedication to innovation, efficiency, and reliability. With advanced technologies and robust features, these products cater to a wide range of industrial applications, making them essential tools for businesses aiming to optimize their operations. Whether for process control, automation, or precision management, Honeywell continues to provide solutions that drive success in the modern industrial landscape.
Top Page Image Contents