!1 Speaker outputs (SURROUND BACK/
MULTI SPEAKER/SPEAKER C)
Two terminals are provided for the front left, and right speakers for multiroom or surround back. The terminals can be used to connect a third set of speakers by setting the SPEAKER C switch to ON. (See page 27)
!2 Speaker output
Seven terminals are provided for the front (A) left, front (A) right, front (B) left, front (B) right, front center, surround left and surround right speakers.
!3 AC INLET
Plug the supplied power cord into this AC INLET and then into the power outlet on the wall.
The SR9600 can be powered by 120 V AC only.
!4 AC OUTLETS
Connect the AC power cables of components such as DVD and CD players to these outlets. “SWITCHED” and “UNSWITCHED” outlets are provided.
The one marked “SWITCHED” provides power only when the SR9600 is turned on and is useful for components which you use every time you play your system.
The one marked “UNSWITCHED” is always live as long as the SR9600 is plugged into a live outlet. A component connected here may be left on permanently, or may be switched off with via its own power switch.
Caution:
•In order to avoid potential issues, anything plugged into these outlets should be powered up before the SR9600 is turned on.
•The capacity of this AC outlet is 120 W. Do not connect devices that consume electricity more than the capacity of these AC outlets. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.
!5 FM antenna 1, 2 (75 ohms)
Connect an external FM antenna with a coaxial cable, or a cable network FM source.
AM antenna and ground 1, 2
Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”. The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna until you hear the best reception.
!6 MONITOR OUT
These are the monitor outputs. Each one includes both composite video and
!7 COMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component video connectors, be sure to connect them to these connectors on the SR9600. The SR9600 has 4 component video input connectors to obtain the color information (Y, CB/PB, CR/PR) directly from the recorded DVD signal or other video component and 2 component video output connectors to output it directly into the matrix decoder of the display device.
By sending the pure DVD component video signal directly, the DVD signal forgoes the extra processing that normally would degrade the image. The result is vastly increased image quality, with incredibly
!8 MULTIROOM REMOTE IN/OUT
IN: Connect to a multiroom remote control device, available from your Marantz dealer.
OUT: Connect to a Marantz component equipped with remote control
!9 REMOTE CONT. IN/OUT
Connect to a Marantz component equipped with remote control
@0 IR RECEIVER IN
Connect to an external IR receiver.
@1 FLASHER IN (Flasher input terminal)
These terminals are for controlling the unit from each room using a keypad, etc.
@2 EMITTER OUT
The signals input to the IR RECEIVER IN terminals are output to this terminal. External devices can be controlled by connecting them to this terminal.
@3 DC TRIGGER output
Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc.) Use the OSD menu system to determine the conditions in which these jacks will be active. (See page 45)
Note:
•This output voltage is for status control only. It is not sufficient for drive capability.
@4 RS232C
The RS232C port is used in conjunction with an external controller to control the operation of the SR9600 using an external device.
The RS232C port may also be used in the future to update the operating software of the SR9600 so that it will be able to support new digital audio formats and other feature as they are introduced.
@5 HDMI INPUT/OUTPUT
This unit has 2 HDMI inputs and 1 HDMI output. The input function can be selected from the OSD menu system. (See page 24)
ENGLISH
9