Marantz SR9600 manual Loading Batteries, REMOTE-CONTROLLABLE Range

ENGLISH	REMOTE CONTROLLER
	RC3200B
	NAMES AND FUNCTIONS
	12
	11
	10
	9
		1
	8
	7	VOLOKCH2

FH(Mute) button

Press this button to mute the sound temporarily.

G VOL (Volume) up and down buttons

Press these buttons to raise and lower the SR9600’s volume level.

HOK and cursor (Up/Down/Left/Right )

buttons

Press these buttons to navigate through the OSD menu system.

(Refer to “ON SCREEN DISPLAY MENU SYSTEM” on page 30)

IPage up/down buttons

Press these buttons to scroll up or down the contents of LCD touch screen.

JBacklight ˆbutton

Press this button to turn on the backlight of the LCD touch screen.

LOADING BATTERIES

When you use RC3200B for the first time, you have to install the batteries.

The RC3200B requires 3 AA batteries (3 x 1.5 V) to function.

Note:

•The included batteries are for verifying functionality of the remote control unit. When replacing the batteries, either rechargeable or non-rechargeable batteries may be used.

1.Remove the back cover.

2. Insert the new batteries (AA type) with correct and polarity.

CAUTIONS ON BATTERIES

•	Use “AA” (R6P) batteries in this remote control
	unit.
• If the remote control unit does not operate from
	close to the main unit, replace the batteries with
	new ones, even if less then a year has passed.
•	The included battery is only for verifying
	operation. Replace it with a new battery as soon
	as possible.
• When inserting the batteries, be careful to do so
	in the proper direction, following the marks in the
	remote control unit’s battery compartment.
	- To prevent damage or battery fluid leakage:
	- Do not use a new battery with an old one.
	- Do not use two different types of batteries.
	- Do not short-circuit, disassemble, heat or
	dispose of batteries in flames.
•	Remove the batteries when not planning to use
	the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
	fluid from the inside of the battery compartment,
	then insert new batteries.
•	When disposing of used batteries, please
	comply with governmental regulations or

6	S	3
Ex	M
5		4

ASelect buttons for navigation bar

These buttons control the navigation bar in LCD touch screen. Each function may also be provided with an alphanumeric indicator visible in the navigation bar of LCD touch screen.

B CH (Channel) up and down buttons

Press these buttons to select the SR9600 tuner presets or TV channels.

CS (Status) button

Press this button to see the SR9600 status on the LCD touch screen.

DM (Menu) button

Press this button to enter the OSD menu system.

EEx (Exit) button

Press this button to exit the OSD menu system.

K Serial port

Connect the RC3200B with your computer using an RS232C cable for future upgrades.

L LCD touch screen

The LCD touch screen is divided into different sections:

wed Jun 01	4:40pm	In this area, you can	3. Close until it clicks.
1/8 A/V Amp
Source Select		see the device you are
		operating.
		Operate your device
		with these soft buttons.

Notes:

• Do not mix alkaline and manganese batteries.

• Do not mix old and new batteries.

environmental public instruction’s rules that

apply in your country or area.

REMOTE-CONTROLLABLE RANGE

The distance between the transmitter/receiver of the remote control unit and the infrared sensor of the SR9600 should be less than about 16.4 ft (5 meters).

If the transmitter/receiver is pointed away from the infrared sensor or if there is an obstacle between them, remote control may not be possible.

60°

	.
	Approxft	m)
	(5
	.4
Remote control unit	16
(RC3200B)

10