Recording the video from one source and the audio from another
You can add the sound from one source to the video of another source to make your own video recordings.
Below is an example of recording the sound from a compact disc player connected to CD IN and the video from a video camera connected to VCR1 to video cassette recorder connected to the VCR2/
1. Switch the video input source to VCR1 by
tapping the VCR1 on page 1/8 on the remote control unit.
1. | wed Jun 01 | 4:40pm |
1/8 A/V Amp |
| |
| Source Select |
7.1 CH INPUT | Adjust the speaker output levels so that you | ||||
can hear the same sound level from each | |||||
The SR9600 is equipped for future expansion | |||||
speaker at the listening position. For the front | |||||
through support for SACD multichannel or DVD- | left, front right, center, surround left, surround | ||||
Audio players. | |||||
right and surround back speakers, the output | |||||
When this is selected, the input signals connected | |||||
levels can be adjusted between | |||||
to the L (front left), R (front right), C (center), SL | |||||
The subwoofer can be adjusted between | |||||
(surround left), SR (surround right), SBL (surround | |||||
back left) and SBR (surround back right) channels | and +12 dB. |
|
|
| |
of the 7.1 CH. In jacks are output directly to the | These adjustments result will be stored to the | ||||
front (left and right), center, surround (left and | 7.1 CH. Input memory. |
|
|
| |
right) and surround back speaker systems as well | 3. Adjust the main volume with the VOLUME | ||||
as the | control knob on the front panel or the VOL / | ||||
surround circuitry. | |||||
buttons on the remote. |
|
|
| ||
In addition, the signal input to the SW (subwoofer) |
|
|
| ||
3. |
|
|
| ||
jack is output to the PRE OUT SW (subwoofer) jack. |
|
|
| ||
The video input source for 7.1 channel input is set |
|
|
|
| |
on the 7.1 CH INPUT SETUP menu. (See page 33) |
|
|
|
| |
This permits simultaneous viewing with video |
|
|
|
| |
sources. | 3. |
|
|
| |
| VOL | OK | CH |
SPEAKER A/B |
| ENGLISH |
|
| |
| wed Jun 01 4:40pm |
|
| 7/8 A/V Amp |
|
| Speaker A/B |
|
The SR9600 allows you to select speaker system A and speaker system B for the front L/R channels. You can select these systems by pressing the SPEAKERS A/B button on the front panel or by tapping
1.
2.
1. Press the 7.1 CH INPUT button on the front | H | S |
panel or tap the 7.1 input on (page 1/8) on the | Ex | M |
|
|
remote control unit to switch to 7.1 channel input.
on the remote control unit.
AUX2 INPUT
2. Switch the audio input source to CD by
tapping the CD on page 1/8 on the remote control unit.
3. “CD” is now selected as the audio input
source and “VCR1” as the video input source.
Notes:
•If you change the input source during recording, you will record the signals from the newly selected input source.
•You cannot record surround effects.
•Digital input signals are only output to the digital outputs. There is no conversion from digital to analog.
When connecting CD players and other digital components, do not connect only the digital terminals, but the analog ones as well.
1. | wed Jun 01 | 4:40pm |
| |
| 1/8 | A/V Amp |
|
|
|
| Source Select |
| |
|
|
| 1. | To cancel the 7.1 CH. Input setting, press the 7.1 |
|
|
| CH INPUT button on the front panel or tap the 7.1 | |
|
|
|
| |
|
|
|
| input off on the remote control unit. |
|
|
|
| Notes: |
|
|
|
| • When the 7.1 CH. Input mode is activated, you |
|
|
|
| may not select a surround mode, as the external |
|
|
|
| decoder determines processing. |
|
|
|
| • In addition, there is no signal sent to the record |
|
|
|
| outputs when the 7.1 CH. Input mode is activated. |
|
|
|
|
|
| • The SR9600 has two input modes: 5.1 channel |
2. If it is necessary to adjust the output level of | and 7.1 channel. Set the input mode on the 7.1 CH | |||||
INPUT SETUP menu. (See page 33) | ||||||
each channel, tap the CH Sel and Ch Level | 5.1 Channel Input mode: | |||||
(PAGE6/8) on the remote control unit. | Surround processing such as for THX music is | |||||
|
|
|
|
|
| performed for 5.1 channel input, excluding |
|
|
|
|
|
| |
|
| wed Jun 01 | 4:40pm |
|
| |
|
|
| surround back left and right channels. | |||
|
|
|
|
|
| |
|
| 6/8 A/V Amp |
|
|
| 7.1 Channel Input mode: |
|
| Tone Adjust |
| |||
|
|
|
|
|
| Surround processing is not performed for 7.1 |
|
|
|
|
|
| channel analog input. |
2.
If you don’t need to connect 7.1 channel input terminals for multichannel decoding, the L (front left) and R (front right) input terminals can be used for AUX2 input.
In this case, you can connect additional audio sources to AUX2.
1. To select AUX2, turn the INPUT SELECTOR
knob on the front panel.
Tap the A/V Amp on the remote control unit
and press the page up button until page 1/8 is
displayed. Tap the AUX2 on the remote control unit.
1. | wed Jun 01 | 4:40pm |
1/8 A/V Amp |
| |
| Source Select |
1.
57