Marantz SR9600 manual CH Input Setup, Mode, Dig, Comp

Press the OK/ENTER button.

Select each mode setting and input terminal with the or cursor buttons.

Press the OK/ENTER button.

Repeat steps 2-5 until all items are set.

1-1 FUNC INPUT SETUP (ASSIGNABLE DIGITAL INPUT)

The 8 and F (Front) digital inputs can be assigned to a desired source.

HDMI and COMPONENT inputs can be assigned to the preferred source.

Use this menu to select which digital input jacks are to be assigned to which input source.

1. Select “FUNC INPUT SETUP” from the

1.INPUT SETUP menu with theorcursor

buttons and press the OK/ENTER button.

		F U N C I N P U T S E T U P 1
	F U N C : M O D E				D I G		HDMI	COMP
	D V D :			A U T O	2		1	1
	L D		:	A N A	3		-	-
	T V		: D I G . 1		1		-	-
	D S S : H D M I 2				5		2	2
	V C R 1		: i . 1		-		-	3
	V C R 2 : A N A				4		-	4
	A U X 1 : A U T O				F		-	-
	R E T U R N					N E X T E X I T
2. Select a setting with the						,	,	, and cursor

buttons, and assign a mode and input jack (DIG, HDMI, COMP).

MODE

AUTO:

Select “AUTO”, for automatic detection of the digital input signal condition.

If there is no digital signal, but there is an analog signal present, the analog signal will be played. "AUTO" is the initial setting of all input sources.

DIG. X:

Select “DIG. X”, when only a digital signal will be used.

ANA:

Select “ANA” for input sources for which no digital input jacks are used.

HDMI:

Select “HDMI1” or “HDMI2”.

i.LINK:

Select a number that can be set to i.LINK.

“i.LINK” appears only when an i.LINK device has been assigned as an input source as explained in “i.LINK SETUP”. (See page 34)

DIG

8 and F(Front) digital inputs can be assigned to a desired source.

Assign the number of a digital input jack to the device.

HDMI

Assign the number of an HDMI input jack to the device.

COMP

Assign the number of a component video input jack to the device.

3.

4.

5.

6.

7. After you complete this portion of the setup, move the cursor to “NEXT” with the , , andcursor buttons and then press the OK/ ENTER button to go to the next page.

F U N C I N P U T S E T U P 2

F U N C : M O D E	D I G		HDMI	COMP
T A P E : A U T O		-	＊�	＊�
C D - R : D I G . 7		7	＊�	＊�
C D : A N A	6		＊�	＊�
A U X 2 : A U T O	-		＊�	＊�
R E T U R N B A C K				E X I T

8. Repeat steps 2-5 until all items are set.

After you complete this portion of the setup, move the cursor to “RETURN” with , , and cursor buttons and press the OK/ ENTER button.

To return to the Func Input Setup 1 menu from the Func Input Setup 2 menu, move the cursor to "BACK" with the , , and cursor buttons and press the OK/ENTER button.

1-2 7.1 CH INPUT SETUP

This menu is for adjusting the speaker levels for 7.1-channel input sources.

Here you will adjust the volume for each channel so that they are all heard by the listener at the same level.

1. Select “7.1 CH INPUT SETUP” from the

1.INPUT SETUP menu with theorcursor buttons and press the OK/ENTER button.

7 . 1 C H I N P U T S E T U P 1

I N P U T M O D E	:	5 . 1 C H
V I D E O - I N	:	L A S T
R E T U R N	N E X T E X I T

2. Select “INPUT MODE” with theorcursor buttons.

3. Select “7.1 CH” or “5.1 CH” with theand cursor buttons.

4. Select “VIDEO IN” with the or cursor buttons.

5. Using the or cursor buttons, select the video input source to be played through the MONITOR OUT jack.

The input source is switched by pressing the orcursor buttons as follows;

LAST ↔ DVD ↔ LD ↔ TV ↔ DSS ↔ VCR1

↔VCR2 ↔ AUX1 ↔ V-OFF ↔ LAST ↔...

Notes:

•When “LAST” is selected, the source is set to the source selected before the 7.1 ch input menu was activated.

•When “V-OFF” is selected, no signal is emitted from MONITOR OUT jack.

6.After you complete this portion of the setup,

move the cursor to “NEXT” with the , , and cursor buttons and press the OK/ ENTER button to go to the next page.

7 . 1 C H I N P U T S E T U P 2

F R O N T L		:		0 . 0 d B
C E N T E R		:	+	0 . 5 d B
F R O N T R		:	+ 1 0 . 0 d B
S U R R . R		:	+ 6 . 5 d B
S U R R . B R		:	- 1 0 . 0 d B
S U R R . B L		:	- 1 0 . 0 d B
S U R R . L		:	+ 6 . 5 d B
S U B W		:	+ 1 2 . 0 d B
R E T U R N	B A C K			E X I T

7.	Select desired channel with the	or	cursor
				ENGLISH
8.	buttons.
	Using the or cursor buttons, adjust the
	volume level of each channel.
Move the cursor to “RETURN” with the		,	, and
cursor buttons, and press the OK/ENTER button
to go to the 1.INPUT SETUP menu.

To return to the 7.1 Ch Input Setup 1 menu from the

7.1Ch Input Setup 2 menu, move the cursor to “BACK” with the , ,andcursor buttons and press the OK/ENTER button.

Note:

•The volume level can be set between -12 dB and +12 dB in 0.5 dB increments on all channels except the subwoofer (SUB W), which can be set from -18 dB to +12 dB in 0.5 dB increments.

33