Dimension One Spas manual Sarena Bay Export Owner’s Manual

Page 25
Manual background

2003 Sarena Bay™

Export Owner’s Manual

15.Push the Jet Pump 3 Button once to turn on pump 3. Let the system run for 10 to 15 seconds to prime the pump.

16.Then push the Jets Button on the Dynamic Massage Sequencer to the right of the Top Side Control to start pump 1. Let it run for 10 to 15 seconds to prime pump 1. Press the button again to shut the pump off.

17.Then push the Jets Button on the Dynamic Massage Sequencer to the left of the Top Side Control to start pump 2. Let it run for 10 to 15 seconds to prime pump 2. Press the button again to shut the pump off.

If there is no jet action, then the water level is too low or there is air trapped in the plumbing lines. To eliminate the trapped air, turn the pumps on and off several times to force the trapped air through the pumps. If there is still no jet action, and the bleeder valves were removed as previously described, turn off the pumps and loosen the top pump unions slightly to let any trapped air escape. Re-tighten the pump unions and turn the pumps on again. Turn the pumps on and off several times until jets function properly.

Ozone bubbles will continue to release from the skimmer recess Ultra Pure bleeder valve as long as the valve remains open. Once the pumps are primed, be sure that the bleeder is closed tightly.

Note

12.When the jets are in full operation, replace and close the bleeder valves and push the UP/Down Buttons until your desired water temperature (set temperature) is indicated on the Digital Display Window. The Digital Display Window will then display your set temperature for thirty seconds before changing to display the current water temperature.

While setting the temperature, the Digital Display Window will read out the temperature – up to 40°C (≅104° F). Water temperatures in excess of 40° C (≅104° F) should be used with extreme caution.

Warning

Note

Initial start-up, you can confirm that the heater is on by looking to see that the heat LED indicator located on the right side of the hot tub control panel is illuminated. A scrolling message will also appear on the lower line of the Digital Display Window reading SPA HEATING TO _ _ _° C (whatever the set temperature is) as well as an animated icon on the Digital Display Window. Once you have verified that the heater is functioning, you can reinstall the ventilated equipment access panel.

19

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Page 2003 Sarena Bay Export Owner’s Manual PERSONAL THERAPY CONTROL PATENT PENDING SWITCHES Table of ContentsHYDROSPORT AQUATIC FITNESS GEAR OPTIONAL Export Owner’s ManualADJUSTING THE FOUNTAIN USING THE TOP SIDE CONTROLS2003 Sarena Bay Export Owner’s ManualSPECIAL COLD WEATHER INSTRUCTIONS 2003 Sarena Bay Export Owner’s Manual IMPORTANT SAFETY INSTRUCTIONS Safety FirstREAD AND FOLLOW ALL INSTRUCTIONS CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS CAREFULLYTo Reduce the Risk of Injury Hyperthermia Don’t Do’s and Don’tsDON’T block or sit on the filter recess area DON’T allow horseplay or unsupervised use of your Sarena BayDimension One Spas 2611 Business Park Drive Vista, CA 760 Warning SignsPersonal Therapy Control Patent Pending Switches Sarena Bay FeaturesDynamic LED Underwater Lighting FountainInnovative Seating - For Revolutionary Design FeaturesBio-Wall / Bench Seat BioForm ReclinersPivot feature “No-float” angles Upright position Multiple Lounges AccommodatePivot Seat Bench SeatSport Zone Seat Frontal Therapy Seatjets the front part of the upper and lowerTop Side Control Additional Design FeaturesScrolling Message Center section Dynamic Massage Sequencer PTC SwitchesFountain Synchronous Spa LightsHydroSport / OptiMounts Weir Basket / SkimmerSoft Tile Pillow Jet System Selector Valve NeckFlex Jet PillowInfraRed Sensor Remotely Control The Sarena BayVision UltraPure Water Management SystemSmart Heat Load SharingHydroSport Aquatic Fitness Gear Optional D1 Remote Control OptionalSonic Immersion System SIS Optional Initial Startup Weir Skimmer/Filter 2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual Operation Using The Top Side ControlsScrolling Message Center Jet Pump 3 Button JETS 1&2 ButtonFeature Water Feature Button Up / Down Buttons PROGRAM Button Light / Enter ButtonRinse Filters Clean Filters Heat Status Light Dimension One Spas ICON Logo→Scrolling Message Center Messages Change Water Change Vision Cartridge DO NOT ENTER THE WATER when “OVERHEAT” is displayed onSpa Check Up OverheatErroneous Temperature on the Display Ice Flashing Display and/or “Check Water Level”Cooling Programming the Scrolling Message Center Setting the TimeSummer Mode Standby Mode Filter Cycle Duration Filter Cycle Start TimeNumber of Filter Cycles Pump Run TimeVision Cartridge Temperature Unit SelectionWaterfall Run Time Digital Display Window InvertProgramming Lock Control Panel ResetProgramming Unlock Control Panel Description Dynamic Massage SequencerLIGHT Button JETS ButtonBEGIN/PAUSE Button SPEED ButtonSEQUENCE Button Massage ZonesZone A Massage Zone DescriptionZone B Zone COperating the Dynamic Massage Sequencer Zone FAdjusting Water Flow Adjusting the FountainJet System Selector Valve Standard VCR Jets→ - Directional Adjustable and Interchangeable JetsStandard VCR Jets→ - Rotator Mini VCR Jets→ - Directional Mini VCR Jets→ - Rotatora Mini VCR Jets→- Rotator Euro Jets - DirectionalFilter Cleaning Routine Equipment MaintenanceDraining Your Equipment Surface Care Light Bulb ReplacementUltralife→ Shell Special Cold Weather Instructions Dimension One “ EnviroTect” Skirts and Vinyl CoversCare for the Wood Spa Cabinet Items Required for WinterizingProcedure for Winterizing Spring Time Startup Warranty Service Information Term Glossary of TermsDefinition Pump Symptom Troubleshooting GuideProblem Heating SystemWater System Electrical System Cont2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual
Top Page Image Contents