Dimension One Spas Sarena Bay Scrolling Message Center Messages, Rinse Filters Clean Filters

Page 31
Heat Status Light

Heat Status Light

Dimension One Spas ICON (Logo)

2003 Sarena Bay

Export Owner’s Manual

The Heat Status Light will turn on when there is a call for heat and the heater engages. This is a normal function. The right side of the Digital Display Window will continue to read the current temperature while the bottom left corner will scroll the message “HEATING TO _ _ _° C” until the hot tub reaches the set temperature. An animated thermometer will also be displayed in the upper center of the Digital Display Window to confirm heater activity.

If the water reaches 1° C (2° F) above the set temperature, the message

COOLING TO _ _ _ - CIRC PUMP & O3 OFF” will be displayed in the bottom left hand side of the Digital Display Window and a cooling cycle will start.

The time of day can be viewed by pushing the Dimension One Spas ICON- logo on the far right of the control panel. If no other button is pushed within 5 seconds, the display will revert to the hot tub water temperature reading. The pre-set factory default is Fahrenheit.

Pressing the logo for 5 seconds will place the spa in the “Standby” mode and allow the spa to be cleaned without turning off the power.

Scrolling Message Center Messages

Because of the advanced programming features of your scrolling Digital Display Window, your hot tub will prompt you when you need to perform routine maintenance. For example:

Rinse Filters

Clean Filters

Every other month, the top line of your Digital Display Window will read,

RINSE FILTERS” and the message “REMOVE FILTERS & RINSE WITH

HOSE... PUSH AND HOLD ICON BUTTON MORE THAN 3 SECONDS TO RESET THIS MESSAGE” will scroll from right to left on the bottom line of the display.

To reset this message, push and hold the Dimension One Spas ICON (logo)located at the right hand side of the control for 3 seconds.

On alternating months, the top line of your Digital Display Window will read, “DIRTY FILTER” and the message “REMOVE FILTERS & CLEAN IN

SOLUTION... PUSH AND HOLD ICON BUTTON MORE THAN 3 SECONDS TO RESET THIS MESSAGE” will scroll from right to left on the bottom line of the display.

To reset this message, push and hold the Dimension One Spas ICON (logo)Button located at the right hand side of the control for 3 seconds.

25

Image 31
Contents Page 2003 Sarena Bay Export Owner’s Manual Export Owner’s Manual Table of ContentsPERSONAL THERAPY CONTROL PATENT PENDING SWITCHES HYDROSPORT AQUATIC FITNESS GEAR OPTIONALExport Owner’s Manual USING THE TOP SIDE CONTROLSADJUSTING THE FOUNTAIN 2003 Sarena BaySPECIAL COLD WEATHER INSTRUCTIONS 2003 Sarena Bay Export Owner’s Manual READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY Safety FirstIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS CAREFULLYTo Reduce the Risk of Injury Hyperthermia DON’T allow horseplay or unsupervised use of your Sarena Bay Do’s and Don’tsDon’t DON’T block or sit on the filter recess areaDimension One Spas 2611 Business Park Drive Vista, CA 760 Warning SignsFountain Sarena Bay FeaturesPersonal Therapy Control Patent Pending Switches Dynamic LED Underwater LightingInnovative Seating - For Revolutionary Design Features“No-float” angles Upright position Multiple Lounges Accommodate BioForm ReclinersBio-Wall / Bench Seat Pivot featurePivot Seat Bench Seatthe front part of the upper and lower Frontal Therapy SeatSport Zone Seat jetsTop Side Control Additional Design FeaturesScrolling Message Center section Synchronous Spa Lights PTC SwitchesDynamic Massage Sequencer FountainHydroSport / OptiMounts Weir Basket / SkimmerSoft Tile Pillow Remotely Control The Sarena Bay NeckFlex Jet PillowJet System Selector Valve InfraRed SensorLoad Sharing UltraPure Water Management SystemVision Smart HeatHydroSport Aquatic Fitness Gear Optional D1 Remote Control OptionalSonic Immersion System SIS Optional Initial Startup Weir Skimmer/Filter 2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual Operation Using The Top Side ControlsScrolling Message Center Jet Pump 3 Button JETS 1&2 ButtonFeature Water Feature Button Up / Down Buttons PROGRAM Button Light / Enter ButtonRinse Filters Clean Filters Heat Status Light Dimension One Spas ICON Logo→Scrolling Message Center Messages Overheat DO NOT ENTER THE WATER when “OVERHEAT” is displayed onChange Water Change Vision Cartridge Spa Check UpErroneous Temperature on the Display Ice Flashing Display and/or “Check Water Level”Cooling Programming the Scrolling Message Center Setting the TimeSummer Mode Standby Mode Pump Run Time Filter Cycle Start TimeFilter Cycle Duration Number of Filter CyclesDigital Display Window Invert Temperature Unit SelectionVision Cartridge Waterfall Run TimeProgramming Lock Control Panel ResetProgramming Unlock JETS Button Dynamic Massage SequencerControl Panel Description LIGHT ButtonMassage Zones SPEED ButtonBEGIN/PAUSE Button SEQUENCE ButtonZone C Massage Zone DescriptionZone A Zone BOperating the Dynamic Massage Sequencer Zone FAdjusting Water Flow Adjusting the FountainJet System Selector Valve Standard VCR Jets→ - Directional Adjustable and Interchangeable JetsStandard VCR Jets→ - Rotator Euro Jets - Directional Mini VCR Jets→ - RotatorMini VCR Jets→ - Directional a Mini VCR Jets→- RotatorFilter Cleaning Routine Equipment MaintenanceDraining Your Equipment Surface Care Light Bulb ReplacementUltralife→ Shell Items Required for Winterizing Dimension One “ EnviroTect” Skirts and Vinyl CoversSpecial Cold Weather Instructions Care for the Wood Spa CabinetProcedure for Winterizing Spring Time Startup Warranty Service Information Term Glossary of TermsDefinition Pump Heating System Troubleshooting GuideSymptom ProblemWater System Electrical System Cont2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual