Dimension One Spas Sarena Bay manual Flashing Display and/or “Check Water Level”, Cooling

Page 33

Flashing Display and/or “Check Water Level”

Flashing Display and/or “Check Water Level”

Erroneous Temperature on the Display

Ice

2003 Sarena Bay™

Export Owner’s Manual

DO NOT ENTER THE WATER if you see “3 flashing LEDs” on the Top Side Control and/or the message, “CHECK WATER LEVEL -CLEAN

FILTER-IF PROBLEM CONTINUES, TURN OFF POWER AND RESTART THE SYSTEM-IF PROBLEM CONTINUES, CALL FOR SERVICE” in the Digital Display Window. Follow the instructions as stated.

Check the water temperature and if it is above 40° C (≅104° F) and DO NOT ENTER THE WATER.

DO NOT ENTER THE WATER if you see a temperature reading of 0°C (≅32° F) or 57.8° C (≅136° F) without first checking the actual water temperature with a separate thermometer. The system has detected a Temperature Probe Failure and the water may be too hot, or too cold, to safely use.

Contact your local Authorized Dimension One Spas Dealer, or authorized service center.

When “ICE CONDITION” and the water temperature are displayed on the Digital Display Window, the air temperature in the equipment can has gone below a factory-preset level, and the system has activated “Smart Winter Mode.” It will then automatically activate the pump(s) to circulate water.

This is a normal hot tub function. No corrective action is necessary. This feature protects the spa from freezing.

Feature

Cooling		When “COOLING” and the water temperature are displayed on the Digital
		Display Window, the water temperature has reached 1° C (≅2° F) above the
		set temperature. The circulation pump and ozone generator will turn off to
		allow the water to cool back to the set temperature. This is a normal hot tub
		function. No corrective action is necessary.

		The circulation pump and ozone generator will be on while
		either jet pump is on. They will remain on for 30 minutes after
		the pump(s) turn off regardless of the water temperature.
		Note


	The Dimension One Spas Scrolling Message Center Control has a battery back-up that will retain
	the time of day for 30 days – even without an active power source. Additionally, it will also keep
Feature	your custom programming commands for up to 40 years without power. This battery back-up will
	not provide power to heat or operate the hot tub.

27

Image 33

Contents Page 2003 Sarena Bay Export Owner’s Manual PERSONAL THERAPY CONTROL PATENT PENDING SWITCHES Table of ContentsHYDROSPORT AQUATIC FITNESS GEAR OPTIONAL Export Owner’s ManualADJUSTING THE FOUNTAIN USING THE TOP SIDE CONTROLS2003 Sarena Bay Export Owner’s ManualSPECIAL COLD WEATHER INSTRUCTIONS 2003 Sarena Bay Export Owner’s Manual IMPORTANT SAFETY INSTRUCTIONS Safety FirstREAD AND FOLLOW ALL INSTRUCTIONS CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS CAREFULLYTo Reduce the Risk of Injury Hyperthermia Don’t Do’s and Don’tsDON’T block or sit on the filter recess area DON’T allow horseplay or unsupervised use of your Sarena BayDimension One Spas 2611 Business Park Drive Vista, CA 760 Warning SignsPersonal Therapy Control Patent Pending Switches Sarena Bay FeaturesDynamic LED Underwater Lighting FountainInnovative Seating - For Revolutionary Design FeaturesBio-Wall / Bench Seat BioForm ReclinersPivot feature “No-float” angles Upright position Multiple Lounges AccommodatePivot Seat Bench SeatSport Zone Seat Frontal Therapy Seatjets the front part of the upper and lowerAdditional Design Features Top Side ControlScrolling Message Center section Dynamic Massage Sequencer PTC SwitchesFountain Synchronous Spa LightsWeir Basket / Skimmer HydroSport / OptiMountsSoft Tile Pillow Jet System Selector Valve NeckFlex Jet PillowInfraRed Sensor Remotely Control The Sarena BayVision UltraPure Water Management SystemSmart Heat Load SharingD1 Remote Control Optional HydroSport Aquatic Fitness Gear OptionalSonic Immersion System SIS Optional Initial Startup Weir Skimmer/Filter 2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual Using The Top Side Controls OperationScrolling Message Center JETS 1&2 Button Jet Pump 3 ButtonFeature Water Feature Button Up / Down Buttons PROGRAM Button Light / Enter ButtonHeat Status Light Dimension One Spas ICON Logo→ Rinse Filters Clean FiltersScrolling Message Center Messages Change Water Change Vision Cartridge DO NOT ENTER THE WATER when “OVERHEAT” is displayed onSpa Check Up OverheatFlashing Display and/or “Check Water Level” Erroneous Temperature on the Display IceCooling Setting the Time Programming the Scrolling Message CenterSummer Mode Standby Mode Filter Cycle Duration Filter Cycle Start TimeNumber of Filter Cycles Pump Run TimeVision Cartridge Temperature Unit SelectionWaterfall Run Time Digital Display Window InvertControl Panel Reset Programming LockProgramming Unlock Control Panel Description Dynamic Massage SequencerLIGHT Button JETS ButtonBEGIN/PAUSE Button SPEED ButtonSEQUENCE Button Massage ZonesZone A Massage Zone DescriptionZone B Zone COperating the Dynamic Massage Sequencer Zone FAdjusting the Fountain Adjusting Water FlowJet System Selector Valve Adjustable and Interchangeable Jets Standard VCR Jets→ - DirectionalStandard VCR Jets→ - Rotator Mini VCR Jets→ - Directional Mini VCR Jets→ - Rotatora Mini VCR Jets→- Rotator Euro Jets - DirectionalRoutine Equipment Maintenance Filter CleaningDraining Your Equipment Light Bulb Replacement Surface CareUltralife→ Shell Special Cold Weather Instructions Dimension One “ EnviroTect” Skirts and Vinyl CoversCare for the Wood Spa Cabinet Items Required for WinterizingProcedure for Winterizing Spring Time Startup Warranty Service Information Glossary of Terms TermDefinition Pump Symptom Troubleshooting GuideProblem Heating SystemWater System Electrical System Cont2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual