Dimension One Spas Sarena Bay manual Change Water Change Vision Cartridge, Spa Check Up, Overheat

Page 32

Change Water

2003 Sarena Bay™

Export Owner’s Manual

Change Water

Change Vision Cartridge

Every four months the top line of your Digital Display Window will read

“CHANGE WATER” and the message “TURN POWER OFF, DRAIN &

REFILL SPA...PUSH AND HOLD ICON BUTTON MORE THAN 3 SECONDS TO RESET THIS MESSAGE” will scroll from right to left on the bottom line of the display.

To reset this message, push and hold the Dimension One Spas ICON (logo)→ Button located at the right hand side of the control for 3 seconds.

When “CHANGE VISION CARTRIDGE” is displayed on the Digital Display Window, the system is telling you that it is time to replace it.

To reset this message, push and hold the Dimension One Spas ICON (logo)→ Button located at the right hand side of the control for 3 seconds.

If you purchased a Vision cartridge subsequent to the initial start up of your hot tub, please follow the programming instructions for VISION as outlined in the next Vision Cartridge section to set the six-month time frame.

Note

Spa Check Up	When “SPA CHECK UP” is displayed on the Digital Display Window, we
	recommend that you have your hot tub inspected by your dealer as a
	preventative maintenance measure.
	To reset this message, push and hold the Dimension One Spas
	ICON (logo)→ Button located at the right hand side of the
	control for 3 seconds.

	The system can dismiss and reset the maintenance messages by pushing and holding the
	Dimension One Spas ICON (logo)→, on the right end of the control, for 3 seconds. If you
	press the Dimension One Spas ICON (logo)→ for 5 seconds when there is no maintenance
Note	message, it will put the spa in the “Standby” mode.
Note
Overheat		DO NOT ENTER THE WATER when “OVERHEAT” is displayed on
		the control system Digital Display Window because the hot tub is in a high
		temperature condition. If such a condition exists, check the water
		temperature with a certified thermometer and if it is above 40° C (≅104° F),
		remove the hot tub cover and allow the water to cool. If the problem recurs,
		turn off all power to the hot tub and contact your local Authorized
		Dimension One Spas Dealer, or authorized service center.

		The overheat condition could be caused by excessive filtration.
		See the Troubleshooting Guide section for more information.
		Note

26

Image 32

Contents Page 2003 Sarena Bay Export Owner’s Manual Table of Contents PERSONAL THERAPY CONTROL PATENT PENDING SWITCHESHYDROSPORT AQUATIC FITNESS GEAR OPTIONAL Export Owner’s ManualUSING THE TOP SIDE CONTROLS ADJUSTING THE FOUNTAIN2003 Sarena Bay Export Owner’s ManualSPECIAL COLD WEATHER INSTRUCTIONS 2003 Sarena Bay Export Owner’s Manual Safety First IMPORTANT SAFETY INSTRUCTIONSREAD AND FOLLOW ALL INSTRUCTIONS CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS CAREFULLYTo Reduce the Risk of Injury Hyperthermia Do’s and Don’ts Don’tDON’T block or sit on the filter recess area DON’T allow horseplay or unsupervised use of your Sarena BayWarning Signs Dimension One Spas 2611 Business Park Drive Vista, CA 760Sarena Bay Features Personal Therapy Control Patent Pending SwitchesDynamic LED Underwater Lighting FountainRevolutionary Design Features Innovative Seating - ForBioForm Recliners Bio-Wall / Bench SeatPivot feature “No-float” angles Upright position Multiple Lounges AccommodateBench Seat Pivot SeatFrontal Therapy Seat Sport Zone Seatjets the front part of the upper and lowerScrolling Message Center section Additional Design FeaturesTop Side Control PTC Switches Dynamic Massage SequencerFountain Synchronous Spa LightsSoft Tile Pillow Weir Basket / SkimmerHydroSport / OptiMounts NeckFlex Jet Pillow Jet System Selector ValveInfraRed Sensor Remotely Control The Sarena BayUltraPure Water Management System VisionSmart Heat Load SharingSonic Immersion System SIS Optional D1 Remote Control OptionalHydroSport Aquatic Fitness Gear Optional Initial Startup Weir Skimmer/Filter 2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual Scrolling Message Center Using The Top Side ControlsOperation Feature JETS 1&2 ButtonJet Pump 3 Button Water Feature Button Up / Down Buttons Light / Enter Button PROGRAM ButtonScrolling Message Center Messages Heat Status Light Dimension One Spas ICON Logo→Rinse Filters Clean Filters DO NOT ENTER THE WATER when “OVERHEAT” is displayed on Change Water Change Vision CartridgeSpa Check Up OverheatCooling Flashing Display and/or “Check Water Level”Erroneous Temperature on the Display Ice Summer Mode Standby Mode Setting the TimeProgramming the Scrolling Message Center Filter Cycle Start Time Filter Cycle DurationNumber of Filter Cycles Pump Run TimeTemperature Unit Selection Vision CartridgeWaterfall Run Time Digital Display Window InvertProgramming Unlock Control Panel ResetProgramming Lock Dynamic Massage Sequencer Control Panel DescriptionLIGHT Button JETS ButtonSPEED Button BEGIN/PAUSE ButtonSEQUENCE Button Massage ZonesMassage Zone Description Zone AZone B Zone CZone F Operating the Dynamic Massage SequencerJet System Selector Valve Adjusting the FountainAdjusting Water Flow Standard VCR Jets→ - Rotator Adjustable and Interchangeable JetsStandard VCR Jets→ - Directional Mini VCR Jets→ - Rotator Mini VCR Jets→ - Directionala Mini VCR Jets→- Rotator Euro Jets - DirectionalDraining Your Equipment Routine Equipment MaintenanceFilter Cleaning Ultralife→ Shell Light Bulb ReplacementSurface Care Dimension One “ EnviroTect” Skirts and Vinyl Covers Special Cold Weather InstructionsCare for the Wood Spa Cabinet Items Required for WinterizingProcedure for Winterizing Spring Time Startup Warranty Service Information Definition Glossary of TermsTerm Pump Troubleshooting Guide SymptomProblem Heating SystemElectrical System Cont Water System2003 Sarena Bay Export Owner’s Manual 2003 Sarena Bay Export Owner’s Manual